Babak Shotorban
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Babak Shotorban has a total of 83 co-authors. Here are the top co-authors by number of shared publications:
- Shankar Mahalingam
Department of Mechanical and Aerospace Engineering, The University of Alabama in Huntsville, Huntsville, Alabama, USA
15 shared publications F. Mashayek
7 shared publicationsS. Balachandar
Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, Florida 32611, USA
5 shared publicationsFarzad Mashayek
University of Illinois at Chicago, Mechanical & Industrial Engineering Department , Chicago, IL, 60607, USA ; Postdoctoral Research Associate, Center for Simulation of Advanced Rockets , University of Illinois at Urbana-Champaign , Urbana, IL, 61801, USA
4 shared publicationsAditya Mankame
3 shared publicationsAmbarish Dahale
ADepartment of Mechanical and Aerospace Engineering, University of Alabama in Huntsville, AL 35899, USA
3 shared publications
Latest Publications
- 4 August 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 271
Equilibrium moisture evaporation model for a particle: A lumped-mass formulation
- 4 August 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 271
Equilibrium moisture evaporation model for a particle: A lumped-mass formulation
- Open Access
- 20 April 2026
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 35 (4)
Physics-based modeling of fire spread in small-scale fuel beds using multiple-reaction pyrolysis kinetics
Background: Physics-based models often use single-step reaction schemes for thermal pyrolysis. However, more detailed schemes may be needed to accurately represent fuels such as pine needles that are composed of multiple chemical components. To this end, a multi-reaction kinetic scheme accounting for lipids, digestives, hemicellulose, etc. content was evaluated. Aims: Validate the scheme against previous thermogravimetric analysis (TGA) experiments and assess its impact in physics-based modeling. Methods: Analytical and numerical solutions were obtained for the scheme under TGA conditions. It was implemented in Fire Dynamics Simulator (FDS) to physically model previous ignition and fire spread experiments in two setups including small scale fuel beds. Key results: Analytical and numerical mass loss rates matched perfectly and agreed with TGA data. In the first fuel bed setup, simulated ignition time, mass loss and mass loss rates aligned well with experiments. In the second setup, simulations in general overestimated temperatures and heat fluxes but performed better than those using a single-step scheme. Conclusions: The multi-reaction scheme reproduced TGA data accurately and improved the physics-based modeling predictions for ignition and fire spread in small-scale fuel beds. Implications: Multiple-reaction pyrolysis schemes may be needed to improve the physical modeling of various fire scenarios.
- 20 April 2026
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 35 (4)
Open AccessPhysics-based modeling of fire spread in small-scale fuel beds using multiple-reaction pyrolysis kinetics
Background: Physics-based models often use single-step reaction schemes for thermal pyrolysis. However, more detailed schemes may be needed to accurately represent fuels such as pine needles that are composed of multiple chemical components. To this end, a multi-reaction kinetic scheme accounting for lipids, digestives, hemicellulose, etc. content was evaluated. Aims: Validate the scheme against previous thermogravimetric analysis (TGA) experiments and assess its impact in physics-based modeling. Methods: Analytical and numerical solutions were obtained for the scheme under TGA conditions. It was implemented in Fire Dynamics Simulator (FDS) to physically model previous ignition and fire spread experiments in two setups including small scale fuel beds. Key results: Analytical and numerical mass loss rates matched perfectly and agreed with TGA data. In the first fuel bed setup, simulated ignition time, mass loss and mass loss rates aligned well with experiments. In the second setup, simulations in general overestimated temperatures and heat fluxes but performed better than those using a single-step scheme. Conclusions: The multi-reaction scheme reproduced TGA data accurately and improved the physics-based modeling predictions for ignition and fire spread in small-scale fuel beds. Implications: Multiple-reaction pyrolysis schemes may be needed to improve the physical modeling of various fire scenarios.
- 19 March 2026
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 196
Multi-reaction kinetic modeling of foliage pyrolysis in wildland fires
- 19 March 2026
- Published by Elsevier in Journal of Analytical and Applied Pyrolysis
- Vol. 196
Multi-reaction kinetic modeling of foliage pyrolysis in wildland fires
- 6 May 2025
- Published by Elsevier in Fire Safety Journal
- Vol. 155
Modeling of the gravitational deposition of firebrands subject to a turbulent jet flow
- 6 May 2025
- Published by Elsevier in Fire Safety Journal
- Vol. 155
Modeling of the gravitational deposition of firebrands subject to a turbulent jet flow
- Open Access
- 27 August 2024
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 33 (9)
Comparing gas composition from fast pyrolysis of live foliage measured in bench-scale and fire-scale experiments
Background: Fire models have used pyrolysis data from oxidising and non-oxidising environments for flaming combustion. In wildland fires pyrolysis, flaming and smouldering combustion typically occur in an oxidising environment (the atmosphere). Aims: Using compositional data analysis methods, determine if the composition of pyrolysis gases measured in non-oxidising and ambient (oxidising) atmospheric conditions were similar. Methods: Permanent gases and tars were measured in a fuel-rich (non-oxidising) environment in a flat flame burner (FFB). Permanent and light hydrocarbon gases were measured for the same fuels heated by a fire flame in ambient atmospheric conditions (oxidising environment). Log-ratio balances of the measured gases common to both environments (CO, CO2, CH4, H2, C6H6O (phenol), and other gases) were examined by principal components analysis (PCA), canonical discriminant analysis (CDA) and permutational multivariate analysis of variance (PERMANOVA). Key results: Mean composition changed between the non-oxidising and ambient atmosphere samples. PCA showed that flat flame burner (FFB) samples were tightly clustered and distinct from the ambient atmosphere samples. CDA found that the difference between environments was defined by the CO-CO2 log-ratio balance. PERMANOVA and pairwise comparisons found FFB samples differed from the ambient atmosphere samples which did not differ from each other. Conclusion: Relative composition of these pyrolysis gases differed between the oxidising and non-oxidising environments. This comparison was one of the first comparisons made between bench-scale and field scale pyrolysis measurements using compositional data analysis. Implications: These results indicate the need for more fundamental research on the early time-dependent pyrolysis of vegetation in the presence of oxygen.
- 27 August 2024
- Published by CSIRO Publishing in International Journal of Wildland Fire
- Vol. 33 (9)
Open AccessComparing gas composition from fast pyrolysis of live foliage measured in bench-scale and fire-scale experiments
Background: Fire models have used pyrolysis data from oxidising and non-oxidising environments for flaming combustion. In wildland fires pyrolysis, flaming and smouldering combustion typically occur in an oxidising environment (the atmosphere). Aims: Using compositional data analysis methods, determine if the composition of pyrolysis gases measured in non-oxidising and ambient (oxidising) atmospheric conditions were similar. Methods: Permanent gases and tars were measured in a fuel-rich (non-oxidising) environment in a flat flame burner (FFB). Permanent and light hydrocarbon gases were measured for the same fuels heated by a fire flame in ambient atmospheric conditions (oxidising environment). Log-ratio balances of the measured gases common to both environments (CO, CO2, CH4, H2, C6H6O (phenol), and other gases) were examined by principal components analysis (PCA), canonical discriminant analysis (CDA) and permutational multivariate analysis of variance (PERMANOVA). Key results: Mean composition changed between the non-oxidising and ambient atmosphere samples. PCA showed that flat flame burner (FFB) samples were tightly clustered and distinct from the ambient atmosphere samples. CDA found that the difference between environments was defined by the CO-CO2 log-ratio balance. PERMANOVA and pairwise comparisons found FFB samples differed from the ambient atmosphere samples which did not differ from each other. Conclusion: Relative composition of these pyrolysis gases differed between the oxidising and non-oxidising environments. This comparison was one of the first comparisons made between bench-scale and field scale pyrolysis measurements using compositional data analysis. Implications: These results indicate the need for more fundamental research on the early time-dependent pyrolysis of vegetation in the presence of oxygen.
- 20 July 2023
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 168
Firebrand deposition on cubic structures in tandem and parallel arrangements
- 20 July 2023
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 168
Firebrand deposition on cubic structures in tandem and parallel arrangements
- 18 October 2022
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 196 (14) , 2356-2379
Influence of Pyrolysis Gas Composition and Reaction Kinetics on Leaf-Scale Fires
The impact of pyrolysis gas composition and the underlying reaction kinetics on the burning characteristics of a leaf was computationally investigated. The computational configuration resembled a previous experimental setup where vertically oriented manzanita (Arctostaphylos glandulosa) leaves were burned. Different compositions and reaction kinetics for the pyrolysis gas released during the leaf thermal decomposition were examined. The most detailed composition included , , , and , which was suggested by the previous experimental study of pyrolysis products of different plant species. The least involved compositions only included either or . In all considered compositions, in addition to pyrolysis gas, the release of the heavy gas, i.e. tar, was accounted for. Tar breakdown was represented by a single-step reaction with the light gases above and soot as the products where the stoichiometric coefficients were determined by an optimization technique for consistency with the measurements for the tar molecule. The burning simulation results agreed best with the previous experimental data when a mixture of , , was used. The least agreement was noted when pyrolysis gas was represented by only . Inclusion of tar breakdown reaction appreciably increased the overall heat release due to combustion of its products above the leaf.- 18 October 2022
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 196 (14) , 2356-2379
Influence of Pyrolysis Gas Composition and Reaction Kinetics on Leaf-Scale Fires
The impact of pyrolysis gas composition and the underlying reaction kinetics on the burning characteristics of a leaf was computationally investigated. The computational configuration resembled a previous experimental setup where vertically oriented manzanita (Arctostaphylos glandulosa) leaves were burned. Different compositions and reaction kinetics for the pyrolysis gas released during the leaf thermal decomposition were examined. The most detailed composition included , , , and , which was suggested by the previous experimental study of pyrolysis products of different plant species. The least involved compositions only included either or . In all considered compositions, in addition to pyrolysis gas, the release of the heavy gas, i.e. tar, was accounted for. Tar breakdown was represented by a single-step reaction with the light gases above and soot as the products where the stoichiometric coefficients were determined by an optimization technique for consistency with the measurements for the tar molecule. The burning simulation results agreed best with the previous experimental data when a mixture of , , was used. The least agreement was noted when pyrolysis gas was represented by only . Inclusion of tar breakdown reaction appreciably increased the overall heat release due to combustion of its products above the leaf.- 28 July 2021
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Aero Optical Effects over a Cylindrical Turret
View Video Presentation: https://doi.org/10.2514/6.2021-3125.vid In this paper the numerical methods are presented for simulating the aero-optical distortions over a flat-windowed cylindrical turret (FWCT). This work involves two key techniques: large eddy simulation (LES) to accurately compute the local density fluctuations in the turbulent flow that are directly linked to the aero-optical distortion and advection upstream splitting method (AUSM), ie a high-resolution scheme to sufficiently capture the refractive index fields in high Reynolds number flow simulations. The high fidelity computational methods to predict the aero-optical distortions by the flow boundary layer are verified with a benchmark case, ie FWCT, the spatial evolution of refractive index fluctuations and aero-optical distortions over FWCT are quantified, the degradation phenomenon of the optical beam during its propagation through the boundary layer is characterized, the link between these two parameters is understood, the image quality due to aero-optical aberration is evaluated.
- 28 July 2021
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Aero Optical Effects over a Cylindrical Turret
View Video Presentation: https://doi.org/10.2514/6.2021-3125.vid In this paper the numerical methods are presented for simulating the aero-optical distortions over a flat-windowed cylindrical turret (FWCT). This work involves two key techniques: large eddy simulation (LES) to accurately compute the local density fluctuations in the turbulent flow that are directly linked to the aero-optical distortion and advection upstream splitting method (AUSM), ie a high-resolution scheme to sufficiently capture the refractive index fields in high Reynolds number flow simulations. The high fidelity computational methods to predict the aero-optical distortions by the flow boundary layer are verified with a benchmark case, ie FWCT, the spatial evolution of refractive index fluctuations and aero-optical distortions over FWCT are quantified, the degradation phenomenon of the optical beam during its propagation through the boundary layer is characterized, the link between these two parameters is understood, the image quality due to aero-optical aberration is evaluated.
- Open Access
- 10 June 2021
- Published by Frontiers Media SA in Frontiers in Mechanical Engineering
- Vol. 7
Deposition Characteristics of Firebrands on and Around Rectangular Cubic Structures
The focus of the present work is on the deposition of firebrands in a flow over a rectangular cubic block representative of a structure in wildland-urban interface (WUI). The study was carried out by physics based modeling where the wind flow turbulence was dealt with by large eddy simulation (LES) and firebrands were treated by Lagrangian tracking. The Lagrangian equations coupled with the flow solver, accounted for both translational and rotational motions as well as thermochemical degradation of firebrands, assumed to be cylindrical. The dimensions of the structure were varied from 3 to 9 m in the simulations for a parametric study. The simulations were carried out by tracking many firebrands randomly released with a uniform distribution from a horizontal plane 35 m above the ground into the computational domain. The coordinates of the deposited firebrands were used to calculate their normalized number density (number of landed firebrands per unit surface area) to quantify their deposition pattern. On the leewardside of the block, an area, referred to as the safe zone, was identified right behind the structure where firebrands never deposit. The size of the safe zone in the direction perpendicular to the wind was nearly identical to the width of the structure. The length of the safe zone in the wind direction was proportional to the height of the structure. The leeward face of the blocks was never hit by a firebrand. The windward face was hit by many more firebrands than the lateral faces but much less than the top face. The distribution of the number density of the deposited firebrands on the top face was found to be correlated with the flow separation and reattachment on this face.
- 10 June 2021
- Published by Frontiers Media SA in Frontiers in Mechanical Engineering
- Vol. 7
Open AccessDeposition Characteristics of Firebrands on and Around Rectangular Cubic Structures
The focus of the present work is on the deposition of firebrands in a flow over a rectangular cubic block representative of a structure in wildland-urban interface (WUI). The study was carried out by physics based modeling where the wind flow turbulence was dealt with by large eddy simulation (LES) and firebrands were treated by Lagrangian tracking. The Lagrangian equations coupled with the flow solver, accounted for both translational and rotational motions as well as thermochemical degradation of firebrands, assumed to be cylindrical. The dimensions of the structure were varied from 3 to 9 m in the simulations for a parametric study. The simulations were carried out by tracking many firebrands randomly released with a uniform distribution from a horizontal plane 35 m above the ground into the computational domain. The coordinates of the deposited firebrands were used to calculate their normalized number density (number of landed firebrands per unit surface area) to quantify their deposition pattern. On the leewardside of the block, an area, referred to as the safe zone, was identified right behind the structure where firebrands never deposit. The size of the safe zone in the direction perpendicular to the wind was nearly identical to the width of the structure. The length of the safe zone in the wind direction was proportional to the height of the structure. The leeward face of the blocks was never hit by a firebrand. The windward face was hit by many more firebrands than the lateral faces but much less than the top face. The distribution of the number density of the deposited firebrands on the top face was found to be correlated with the flow separation and reattachment on this face.
- 1 March 2021
- Published by AIP Publishing in Physics of Plasmas
- Vol. 28 (3) , 033705
Effects of collision-enhanced charging on dust crystal
Numerical simulations of monolayer dust crystals in a radio frequency (RF) complex plasma were performed to examine the crystal structure and quantify the effects of including the collision-enhanced ion current in the charging model. A gaseous electronics conference (GEC) cell similar to a previous experimental work was modeled for a range of RF voltages, using a continuum description for the plasma and a particle description for dust grains. The time history of each dust grain was monitored. The dust charge was computed using both the orbital motion limited and the collision-enhanced charging (CEC) model applicable to the sheath region. The dust model accounted for the electric force, ion drag force, neutral drag force, gravity, and the ion wake. The CEC model produced a lower charge and lower electric force which agreed better with the experimental data. Then dust crystals composed of 40–100 grains were modeled and the levitation height and inter-particle spacing of the resulting crystals was examined. Including the collision-enhanced current reduced the inter-particle spacing but only had a minor effect on the levitation height.
- 1 March 2021
- Published by AIP Publishing in Physics of Plasmas
- Vol. 28 (3) , 033705
Effects of collision-enhanced charging on dust crystal
Numerical simulations of monolayer dust crystals in a radio frequency (RF) complex plasma were performed to examine the crystal structure and quantify the effects of including the collision-enhanced ion current in the charging model. A gaseous electronics conference (GEC) cell similar to a previous experimental work was modeled for a range of RF voltages, using a continuum description for the plasma and a particle description for dust grains. The time history of each dust grain was monitored. The dust charge was computed using both the orbital motion limited and the collision-enhanced charging (CEC) model applicable to the sheath region. The dust model accounted for the electric force, ion drag force, neutral drag force, gravity, and the ion wake. The CEC model produced a lower charge and lower electric force which agreed better with the experimental data. Then dust crystals composed of 40–100 grains were modeled and the levitation height and inter-particle spacing of the resulting crystals was examined. Including the collision-enhanced current reduced the inter-particle spacing but only had a minor effect on the levitation height.