Rickard Österlöf
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rickard Österlöf has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Henrik Wentzel
3 shared publications- Jenny Jerrelind
Department of Engineering Mechanics, KTH Royal Institute of Technology, Stockholm, Sweden
3 shared publications - Jukka Hyttinen
Scania CV AB, Södertälje, Sweden
3 shared publications - Lars Drugge
Department of Engineering Mechanics, KTH Royal Institute of Technology, Stockholm, Sweden
3 shared publications Leif Kari
2 shared publicationsDaniel Wollscheid
1 shared publication
Latest Publications
- Open Access
Investigating the Influence of Heat-Insulated Wheelhouses on Truck Tyre Temperature and Rolling Resistance
Due to legislations introduced to prevent global warming, vehicle manufacturers must find new ways to reduce CO2 emissions. This paper explores a way to reduce rolling resistance by heat-insulating and covering a truck’s wheelhouse. Truck tyre rolling resistance was measured at +5 °C ambient temperature for consecutive speed steps in a climate wind chamber with and without heat insulation. The study showed that by encapsulating and insulating the wheelhouse, already generated strain-induced heat could be kept in the tyre, consequently leading to reduced rolling resistance. The tyre shoulder temperature was monitored during the experiments along with the tyre pressure. When the wheelhouses were encapsulated, a significant reduction in rolling resistance and an increase in tyre pressure and temperature were measured at all evaluated speed levels.
Open AccessInvestigating the Influence of Heat-Insulated Wheelhouses on Truck Tyre Temperature and Rolling Resistance
Due to legislations introduced to prevent global warming, vehicle manufacturers must find new ways to reduce CO2 emissions. This paper explores a way to reduce rolling resistance by heat-insulating and covering a truck’s wheelhouse. Truck tyre rolling resistance was measured at +5 °C ambient temperature for consecutive speed steps in a climate wind chamber with and without heat insulation. The study showed that by encapsulating and insulating the wheelhouse, already generated strain-induced heat could be kept in the tyre, consequently leading to reduced rolling resistance. The tyre shoulder temperature was monitored during the experiments along with the tyre pressure. When the wheelhouses were encapsulated, a significant reduction in rolling resistance and an increase in tyre pressure and temperature were measured at all evaluated speed levels.
- Open Access
- 27 February 2024
- Published by Springer Nature in Experimental Mechanics
- Vol. 64 (4) , 455-466
Development and Analysis of an On-Road Torque Measurement Device for Trucks
Background: Rolling resistance and aerodynamic losses cause a significant part of a truck’s energy consumption. Therefore there is an interest from both vehicle manufacturers and regulators to measure these losses to understand, quantify and reduce the energy consumption of vehicles. On-road measurements are particularly interesting because it enables testing in various ambient conditions and road surfaces with vehicles in service. Objective: Common driving loss measurement devices require unique instrumented measurement wheels, which hinders effective measurements of multiple tyre sets or measurements of vehicles in service. For this purpose, the objective is to develop a novel load-sensing device for measuring braking or driving torque. Methods: The strength of the measurement device is calculated using finite element methods, and the output signal is simulated using virtual strain gauge simulations. In addition to the signal simulation, the device is calibrated using a torsional test rig. Results: The simulation results confirm that the device fulfils the strength requirements and is able to resolve low torque levels. The output signal is simulated for the novel cascaded multi-Wheatstone bridge using the strains extracted from the finite element analysis. The simulations and measurements show that the measurement signal is linear and not sensitive to other load directions. The device is tested on a truck, and the effort of mounting the device is comparable to a regular tyre change. Conclusions: A novel driving loss measurement device design is presented with an innovative positioning of strain gauges decoupling the parasitic loads from the driving loss measurements. The design allows on-road testing using conventional wheels without requiring special measurement wheels or instrumentation of drive shafts, enabling more affordable and accurate measurements.
- 27 February 2024
- Published by Springer Nature in Experimental Mechanics
- Vol. 64 (4) , 455-466
Open AccessDevelopment and Analysis of an On-Road Torque Measurement Device for Trucks
Background: Rolling resistance and aerodynamic losses cause a significant part of a truck’s energy consumption. Therefore there is an interest from both vehicle manufacturers and regulators to measure these losses to understand, quantify and reduce the energy consumption of vehicles. On-road measurements are particularly interesting because it enables testing in various ambient conditions and road surfaces with vehicles in service. Objective: Common driving loss measurement devices require unique instrumented measurement wheels, which hinders effective measurements of multiple tyre sets or measurements of vehicles in service. For this purpose, the objective is to develop a novel load-sensing device for measuring braking or driving torque. Methods: The strength of the measurement device is calculated using finite element methods, and the output signal is simulated using virtual strain gauge simulations. In addition to the signal simulation, the device is calibrated using a torsional test rig. Results: The simulation results confirm that the device fulfils the strength requirements and is able to resolve low torque levels. The output signal is simulated for the novel cascaded multi-Wheatstone bridge using the strains extracted from the finite element analysis. The simulations and measurements show that the measurement signal is linear and not sensitive to other load directions. The device is tested on a truck, and the effort of mounting the device is comparable to a regular tyre change. Conclusions: A novel driving loss measurement device design is presented with an innovative positioning of strain gauges decoupling the parasitic loads from the driving loss measurements. The design allows on-road testing using conventional wheels without requiring special measurement wheels or instrumentation of drive shafts, enabling more affordable and accurate measurements.
- 6 August 2022
- Published by Springer Nature
- p. 1005-1014
Simulation of a Truck Tyre Using a Viscoplastic Constitutive Rubber Model
- 6 August 2022
- Published by Springer Nature
- p. 1005-1014
Simulation of a Truck Tyre Using a Viscoplastic Constitutive Rubber Model
- 1 December 2016
- Published by Elsevier in International Journal of Plasticity
- Vol. 87, 1-14
A finite strain viscoplastic constitutive model for rubber with reinforcing fillers
- 1 December 2016
- Published by Elsevier in International Journal of Plasticity
- Vol. 87, 1-14
A finite strain viscoplastic constitutive model for rubber with reinforcing fillers
- 1 February 2015
- Published by Elsevier in Polymer Testing
- Vol. 41, 44-54
An efficient method for obtaining the hyperelastic properties of filled elastomers in finite strain applications
- 1 February 2015
- Published by Elsevier in Polymer Testing
- Vol. 41, 44-54
An efficient method for obtaining the hyperelastic properties of filled elastomers in finite strain applications
- 1 October 2014
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 51 (19-20) , 3431-3438
Constitutive modelling of the amplitude and frequency dependency of filled elastomers utilizing a modified Boundary Surface Model
- 1 October 2014
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 51 (19-20) , 3431-3438
Constitutive modelling of the amplitude and frequency dependency of filled elastomers utilizing a modified Boundary Surface Model