Werner Prost
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Werner Prost has a total of 371 co-authors. Here are the top co-authors by number of shared publications:
F.-J. Tegude
University Duisburg-Essen Solid-State Electronics Department and CENIDE Lotharstraße 55, D-47057 Duisburg, Germany
28 shared publicationsF.J. Tegude
23 shared publicationsF. Scheffer
18 shared publicationsQ. Liu
Dept. of Solid State Electron., Duisburg Univ., Germany
18 shared publications- Franz-Josef Tegude
Solid State Electronics Department, Gerhard-Mercator-University GH Duisburg, Kommandantenstrasse 60, D-47057 Duisburg, Germany
16 shared publications U. Auer
16 shared publications
Latest Publications
- Open Access
- 12 November 2024
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (4)
Scanning Transmission Electron Microscopy Analysis of the Si(111)–AlN–GaN Nanowire Interface Grown by Polarity‐ and Site‐Controlled Growth Method
In GaN‐on‐Si nanowire integration schemes, where the nanowires are contacted through the substrate, the interfaces between silicon substrate, AlN buffer layer, and GaN nanowire are of high interest. Herein, analysis by scanning transmission electron microscopy (STEM) of GaN nanowires grown on Si(111) by metal–organic vapor phase epitaxy using a polarity‐ and site‐controlled growth method is presented. This method is based on prestructuring the substrate, ex situ oxidation of the surface, and in situ oxide layer desorption. First, an AlN layer is grown to prevent melt‐back etching. Samples are prepared for STEM by focused ion beam cutting. STEM measurements in three different regions reveal that the AlN buffer material is polycrystalline. The degree of polycrystallinity is found to depend on the observed region: the highest degree exists at the field area between nanowires and the lowest at the sidewall of the Si‐pillars. On the sidewall, the ‐direction of the AlN grain is tilted by 30.1° with regard to the Si{111} sidewall plane, leading to reduced lattice mismatch at this location. The growth of GaN is competing with diffusion of Ga atoms through grain boundaries. The dominant mechanism is dependent on the region, leading to site‐controlled growth of nanowires.
- 12 November 2024
- Published by Wiley in Physica Status Solidi (a)
- Vol. 222 (4)
Open AccessScanning Transmission Electron Microscopy Analysis of the Si(111)–AlN–GaN Nanowire Interface Grown by Polarity‐ and Site‐Controlled Growth Method
In GaN‐on‐Si nanowire integration schemes, where the nanowires are contacted through the substrate, the interfaces between silicon substrate, AlN buffer layer, and GaN nanowire are of high interest. Herein, analysis by scanning transmission electron microscopy (STEM) of GaN nanowires grown on Si(111) by metal–organic vapor phase epitaxy using a polarity‐ and site‐controlled growth method is presented. This method is based on prestructuring the substrate, ex situ oxidation of the surface, and in situ oxide layer desorption. First, an AlN layer is grown to prevent melt‐back etching. Samples are prepared for STEM by focused ion beam cutting. STEM measurements in three different regions reveal that the AlN buffer material is polycrystalline. The degree of polycrystallinity is found to depend on the observed region: the highest degree exists at the field area between nanowires and the lowest at the sidewall of the Si‐pillars. On the sidewall, the ‐direction of the AlN grain is tilted by 30.1° with regard to the Si{111} sidewall plane, leading to reduced lattice mismatch at this location. The growth of GaN is competing with diffusion of Ga atoms through grain boundaries. The dominant mechanism is dependent on the region, leading to site‐controlled growth of nanowires.
- Open Access
- 3 November 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 221 (13)
Experimental and Theoretical Investigation of Collector Spacer and Doping Profile on Triple‐Barrier Resonant Tunneling Diodes
Upcoming THz applications require compact, robust, and efficient sources with high output‐power. Among electronic devices, resonant tunneling diodes are a promising candidate for THz operation. Triple‐barrier resonant tunneling diodes provide a high degree of design and operation freedom. Zero‐bias detection and THz emission are possible with the same device due to the asymmetric structure and IV curve. However, more investigations in the layer stack design are required. An investigation is presented into the effect of collector spacer thickness and doping profile in the subcollector contact region. The aim is to simultaneously optimize the RF output‐power and cut‐off frequency in triple‐barrier structures. A series of devices with different collector spacers and two distinct doping profiles are fabricated. A trade‐off between collector spacer thickness and doping profile for either higher output power or cut‐off frequency is observed. In addition, the simulation results are presented from a nonequilibrium Green's function solver implemented in Python. Herein, a need for accurate determination of the extent of the nonequilibrium region to achieve simulation results matching the IV measurements is observed.
- 3 November 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 221 (13)
Open AccessExperimental and Theoretical Investigation of Collector Spacer and Doping Profile on Triple‐Barrier Resonant Tunneling Diodes
Upcoming THz applications require compact, robust, and efficient sources with high output‐power. Among electronic devices, resonant tunneling diodes are a promising candidate for THz operation. Triple‐barrier resonant tunneling diodes provide a high degree of design and operation freedom. Zero‐bias detection and THz emission are possible with the same device due to the asymmetric structure and IV curve. However, more investigations in the layer stack design are required. An investigation is presented into the effect of collector spacer thickness and doping profile in the subcollector contact region. The aim is to simultaneously optimize the RF output‐power and cut‐off frequency in triple‐barrier structures. A series of devices with different collector spacers and two distinct doping profiles are fabricated. A trade‐off between collector spacer thickness and doping profile for either higher output power or cut‐off frequency is observed. In addition, the simulation results are presented from a nonequilibrium Green's function solver implemented in Python. Herein, a need for accurate determination of the extent of the nonequilibrium region to achieve simulation results matching the IV measurements is observed.
- Open Access
- 26 July 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (4)
Local optical analysis of InGaN/GaN nanorod LED structures grown on Si(111)
Site- and polarity-controlled core–shell InGaN/GaN nanorod LED structures were grown by metal organic vapor phase epitaxy on Si(111). Scanning transmission electron microscope images reveal uniform multiple quantum wells on polarization-free sidewalls. Spatially resolved photoluminescence mapping on a single nanorod demonstrates that the emission at 3.0 eV stems from the polarization-free m-plane, which is supported by a fast recombination lifetime of ∼490 ps at low temperatures. Quasi-resonant laser excitation demonstrates predominant radiative recombination at low excitation densities, whereas at high excitation densities, the efficiency is lowered by Auger recombination and/or carrier leakage.
- 26 July 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134 (4)
Open AccessLocal optical analysis of InGaN/GaN nanorod LED structures grown on Si(111)
Site- and polarity-controlled core–shell InGaN/GaN nanorod LED structures were grown by metal organic vapor phase epitaxy on Si(111). Scanning transmission electron microscope images reveal uniform multiple quantum wells on polarization-free sidewalls. Spatially resolved photoluminescence mapping on a single nanorod demonstrates that the emission at 3.0 eV stems from the polarization-free m-plane, which is supported by a fast recombination lifetime of ∼490 ps at low temperatures. Quasi-resonant laser excitation demonstrates predominant radiative recombination at low excitation densities, whereas at high excitation densities, the efficiency is lowered by Auger recombination and/or carrier leakage.
- Open Access
- 18 September 2020
- Published by Springer Nature in Nature Communications
- Vol. 11 (1) , 1-7
Hot electrons in a nanowire hard X-ray detector
Nanowire chip-based electrical and optical devices such as biochemical sensors, physical detectors, or light emitters combine outstanding functionality with a small footprint, reducing expensive material and energy consumption. The core functionality of many nanowire-based devices is embedded in their p-n junctions. To fully unleash their potential, such nanowire-based devices require – besides a high performance – stability and reliability. Here, we report on an axial p-n junction GaAs nanowire X-ray detector that enables ultra-high spatial resolution (~200 nm) compared to micron scale conventional ones. In-operando X-ray analytical techniques based on a focused synchrotron X-ray nanobeam allow probing the internal electrical field and observing hot electron effects at the nanoscale. Finally, we study device stability and find a selective hot electron induced oxidization in the n-doped segment of the p-n junction. Our findings demonstrate capabilities and limitations of p-n junction nanowires, providing insight for further improvement and eventual integration into on-chip devices.
- 18 September 2020
- Published by Springer Nature in Nature Communications
- Vol. 11 (1) , 1-7
Open AccessHot electrons in a nanowire hard X-ray detector
Nanowire chip-based electrical and optical devices such as biochemical sensors, physical detectors, or light emitters combine outstanding functionality with a small footprint, reducing expensive material and energy consumption. The core functionality of many nanowire-based devices is embedded in their p-n junctions. To fully unleash their potential, such nanowire-based devices require – besides a high performance – stability and reliability. Here, we report on an axial p-n junction GaAs nanowire X-ray detector that enables ultra-high spatial resolution (~200 nm) compared to micron scale conventional ones. In-operando X-ray analytical techniques based on a focused synchrotron X-ray nanobeam allow probing the internal electrical field and observing hot electron effects at the nanoscale. Finally, we study device stability and find a selective hot electron induced oxidization in the n-doped segment of the p-n junction. Our findings demonstrate capabilities and limitations of p-n junction nanowires, providing insight for further improvement and eventual integration into on-chip devices.
- Open Access
- 27 August 2020
- Published by Wiley in Physica Status Solidi (b)
- Vol. 258 (2)
Tunneling‐Related Leakage Currents in Coaxial GaAs/InGaP Nanowire Heterojunction Bipolar Transistors
Herein, a detailed analysis of leakage mechanisms in epitaxially grown nanowire heterojunction bipolar transistors (NW‐HBTs) is presented. Coaxial npn‐GaAs/InGaP core–multishell nanowires are grown via gold‐catalyzed metalorganic vapor phase epitaxy, processed to three terminal devices and electrically characterized. The key for successful NW‐HBT device functionality is the identification of tunneling as the dominant leakage mechanism in highly doped nanowire pn‐junctions. The suppression of forward tunneling currents by adjustment of the tunneling barrier width reduces the junction leakage current density into the nA cm−2 regime, which is further verified by tunneling‐related electroluminescence measurements. In addition, the suppressed tunneling accordingly increases the number of electrons that are injected from the n‐emitter into the p‐base. The latter effect influences the performance of pn‐junction based devices and is found to enable bipolar transistor functionality. Measured common emitter Gummel plots of the NW‐HBT exhibit a current gain of up to 9 and the transistor function is additionally verified by current‐controlled output characteristics.
- 27 August 2020
- Published by Wiley in Physica Status Solidi (b)
- Vol. 258 (2)
Open AccessTunneling‐Related Leakage Currents in Coaxial GaAs/InGaP Nanowire Heterojunction Bipolar Transistors
Herein, a detailed analysis of leakage mechanisms in epitaxially grown nanowire heterojunction bipolar transistors (NW‐HBTs) is presented. Coaxial npn‐GaAs/InGaP core–multishell nanowires are grown via gold‐catalyzed metalorganic vapor phase epitaxy, processed to three terminal devices and electrically characterized. The key for successful NW‐HBT device functionality is the identification of tunneling as the dominant leakage mechanism in highly doped nanowire pn‐junctions. The suppression of forward tunneling currents by adjustment of the tunneling barrier width reduces the junction leakage current density into the nA cm−2 regime, which is further verified by tunneling‐related electroluminescence measurements. In addition, the suppressed tunneling accordingly increases the number of electrons that are injected from the n‐emitter into the p‐base. The latter effect influences the performance of pn‐junction based devices and is found to enable bipolar transistor functionality. Measured common emitter Gummel plots of the NW‐HBT exhibit a current gain of up to 9 and the transistor function is additionally verified by current‐controlled output characteristics.
- 6 August 2020
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 22 (33) , 5522-5532
A systematic study of Ga- and N-polar GaN nanowire–shell growth by metal organic vapor phase epitaxy
Metal organic vapor-phase epitaxy of GaN shells on N- and Ga-polar nanowires on AlN/Si(111) templates has been studied in detail. A polarity-dependent epitaxial optimization of nitride-based core–shell structures is necessary to attain the desired shell shape. On N-polar wires, a maximal shell length has been achieved using N2, only, as a carrier gas, while the length decreases by substitution of N2 with H2. A strong impact of the NW growth template polarity has been observed, which has to be considered to attain the desired shell shape. On Ga-polar wires under pure N2, an exclusive coverage of the wire tip occurs. Shell growth and an increasing shell length are obtained by injecting increased H2 flows. The semi-polar {101} and polar (000) planes have been identified as the facets that limit the vertical shell length growth evolution on the N- and Ga-polar core–shell structures, respectively. Meanwhile, the m-planar lateral growth mode is found to be identical for both types of polarities. The data are used to set up a growth model that includes the facet-dependent termination, carrier-gas dependent H-passivation, Ga-adatom length and Ga-adlayer formation, and the thereby adjusted three-dimensional growth and shell shape for both polarities. The attained insights and the developed technology allow the epitaxy of homogeneous complex crystal architectures, mandatory for optimized nitride core–shell NW-based devices.
- 6 August 2020
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 22 (33) , 5522-5532
A systematic study of Ga- and N-polar GaN nanowire–shell growth by metal organic vapor phase epitaxy
Metal organic vapor-phase epitaxy of GaN shells on N- and Ga-polar nanowires on AlN/Si(111) templates has been studied in detail. A polarity-dependent epitaxial optimization of nitride-based core–shell structures is necessary to attain the desired shell shape. On N-polar wires, a maximal shell length has been achieved using N2, only, as a carrier gas, while the length decreases by substitution of N2 with H2. A strong impact of the NW growth template polarity has been observed, which has to be considered to attain the desired shell shape. On Ga-polar wires under pure N2, an exclusive coverage of the wire tip occurs. Shell growth and an increasing shell length are obtained by injecting increased H2 flows. The semi-polar {101} and polar (000) planes have been identified as the facets that limit the vertical shell length growth evolution on the N- and Ga-polar core–shell structures, respectively. Meanwhile, the m-planar lateral growth mode is found to be identical for both types of polarities. The data are used to set up a growth model that includes the facet-dependent termination, carrier-gas dependent H-passivation, Ga-adatom length and Ga-adlayer formation, and the thereby adjusted three-dimensional growth and shell shape for both polarities. The attained insights and the developed technology allow the epitaxy of homogeneous complex crystal architectures, mandatory for optimized nitride core–shell NW-based devices.
- 30 January 2020
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 22 (7) , 1239-1250
Spatially controlled VLS epitaxy of gallium arsenide nanowires on gallium nitride layers
We present Au catalyzed p-GaAs nanowire growth on n-GaN layers as a possible method to grow an arsenide on a nitride compound semiconductor by metal organic vapor phase epitaxy. The GaAs growth position, the nanowire density and the nanowire growth direction are controlled by a combination of vapor–liquid–solid growth and selective area epitaxy. Thus, a spatially controlled nanowire growth is attained, which is mandatory for device fabrication. The growth position is defined by lithographically positioned Au discs on n-GaN. By adapting the growth conditions (QTBAs, presaturation) the nanowire density is optimized. Lateral and vertical anisotropic nanowire growth is attained through VLS growth in structured SiOx openings. Critical technological parameters for successful control of the growth direction are the positioning of the Au catalyst in relation to the SiOx mask, the size of the eutectic in relation to the opening dimensions, and the SiOx thickness. These results lead to distinct pn-junction positions and adjustable nanowire growth dimensions and directions.
- 30 January 2020
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 22 (7) , 1239-1250
Spatially controlled VLS epitaxy of gallium arsenide nanowires on gallium nitride layers
We present Au catalyzed p-GaAs nanowire growth on n-GaN layers as a possible method to grow an arsenide on a nitride compound semiconductor by metal organic vapor phase epitaxy. The GaAs growth position, the nanowire density and the nanowire growth direction are controlled by a combination of vapor–liquid–solid growth and selective area epitaxy. Thus, a spatially controlled nanowire growth is attained, which is mandatory for device fabrication. The growth position is defined by lithographically positioned Au discs on n-GaN. By adapting the growth conditions (QTBAs, presaturation) the nanowire density is optimized. Lateral and vertical anisotropic nanowire growth is attained through VLS growth in structured SiOx openings. Critical technological parameters for successful control of the growth direction are the positioning of the Au catalyst in relation to the SiOx mask, the size of the eutectic in relation to the opening dimensions, and the SiOx thickness. These results lead to distinct pn-junction positions and adjustable nanowire growth dimensions and directions.
- Open Access
- 27 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 10 (2) , 221-224
Subharmonic Injection Locking for Phase and Frequency Control of RTD-Based THz Oscillator
Phase and frequency control of Resonant Tunneling Diode (RTD)-based terahertz oscillators are major challenges in realizing coherent signal sources for arrayed applications, such as spatial power combining, beam steering or MIMO systems. In this paper, we demonstrate frequency locking and control of a RTD oscillating at f0 ~ 550 GHz, via radiative injection of a weak sinusoidal sub-harmonic signal at f0/2. Precise frequency control, within the locking range of around 2 GHz, is demonstrated. A peak output power enhancement of 14 dB in the whole locking range, compared to the free running oscillator, is achieved. Furthermore, occurrence of phase locking is identified by the spectral linewidth reduction, quantifiable in the FWHM parameter. A signal linewidth of 490 Hz was achieved in locked operation.
- 27 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 10 (2) , 221-224
Open AccessSubharmonic Injection Locking for Phase and Frequency Control of RTD-Based THz Oscillator
Phase and frequency control of Resonant Tunneling Diode (RTD)-based terahertz oscillators are major challenges in realizing coherent signal sources for arrayed applications, such as spatial power combining, beam steering or MIMO systems. In this paper, we demonstrate frequency locking and control of a RTD oscillating at f0 ~ 550 GHz, via radiative injection of a weak sinusoidal sub-harmonic signal at f0/2. Precise frequency control, within the locking range of around 2 GHz, is demonstrated. A peak output power enhancement of 14 dB in the whole locking range, compared to the free running oscillator, is achieved. Furthermore, occurrence of phase locking is identified by the spectral linewidth reduction, quantifiable in the FWHM parameter. A signal linewidth of 490 Hz was achieved in locked operation.
- 12 November 2019
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 21 (48) , 7476-7488
Mask-less MOVPE of arrayed n-GaN nanowires on site- and polarity-controlled AlN/Si templates
We present a novel approach to attain Ga-polar n-GaN nanowires on n-Si(111)/AlN templates, by site- and polarity-controlled metal organic vapor phase epitaxy. A three-stage process is developed to (i) form equally-sized Ga-polar GaN islands, (ii) change the growth direction towards the vertical direction and finally, to (iii) obtain continuous nanowire epitaxy. Homogeneous islands are achieved by minimizing parasitic nucleation and adjusting the adatom diffusion length to the used nanoimprint pattern. The influence of the carrier gas composition on the polarity is studied, achieving pure Ga-polarity by mostly using nitrogen carrier gas. Enhancing the Si/Ga-ratio leads to an amplification of the vertical growth, but also to a reduced number of NWs. 100% growth is attained by a height dependent V/III-ratio adjustment. The results are supported by a qualitative model, explaining how suppression of multi-pod, parasitic and inhomogeneous crystallization can be realized by trading off in situ SiNx passivation and localized GaN growth.
- 12 November 2019
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 21 (48) , 7476-7488
Mask-less MOVPE of arrayed n-GaN nanowires on site- and polarity-controlled AlN/Si templates
We present a novel approach to attain Ga-polar n-GaN nanowires on n-Si(111)/AlN templates, by site- and polarity-controlled metal organic vapor phase epitaxy. A three-stage process is developed to (i) form equally-sized Ga-polar GaN islands, (ii) change the growth direction towards the vertical direction and finally, to (iii) obtain continuous nanowire epitaxy. Homogeneous islands are achieved by minimizing parasitic nucleation and adjusting the adatom diffusion length to the used nanoimprint pattern. The influence of the carrier gas composition on the polarity is studied, achieving pure Ga-polarity by mostly using nitrogen carrier gas. Enhancing the Si/Ga-ratio leads to an amplification of the vertical growth, but also to a reduced number of NWs. 100% growth is attained by a height dependent V/III-ratio adjustment. The results are supported by a qualitative model, explaining how suppression of multi-pod, parasitic and inhomogeneous crystallization can be realized by trading off in situ SiNx passivation and localized GaN growth.
- 14 March 2019
- Published by Wiley in Physica Status Solidi (b)
- Vol. 256 (4)
Process Development for Wet‐Chemical Surface Functionalization of Gallium Arsenide Based Nanowires
The chemisorption of various functionalizing agents on (100) and (111)B gallium arsenide and (100) indium phosphide substrates is studied to elaborate a wet‐chemical surface coating protocol for gallium arsenide based nanowires. Application of (non‐)fluorinated alkanethiols under different parameters shows great success resulting in a decreased polarity of the surface (confirmed by a significant increase of the water contact angle) and no occurrence of etching effects. The successful functionalization is determined by X‐ray photoelectron spectroscopy measurements. After optimization of concentration, additives and solvents, the process parameters are transferred to both, p‐ and n‐doped GaAs‐based nanowire structures. The influence of surface functionalization on the electrical behavior of the nanowires is determined by current–voltage characteristics. Based on the experimental data, a bonding mechanism for the alkanethiol onto the semiconductor material is proposed and a model for describing surface depletion before and after functionalization is developed.
- 14 March 2019
- Published by Wiley in Physica Status Solidi (b)
- Vol. 256 (4)
Process Development for Wet‐Chemical Surface Functionalization of Gallium Arsenide Based Nanowires
The chemisorption of various functionalizing agents on (100) and (111)B gallium arsenide and (100) indium phosphide substrates is studied to elaborate a wet‐chemical surface coating protocol for gallium arsenide based nanowires. Application of (non‐)fluorinated alkanethiols under different parameters shows great success resulting in a decreased polarity of the surface (confirmed by a significant increase of the water contact angle) and no occurrence of etching effects. The successful functionalization is determined by X‐ray photoelectron spectroscopy measurements. After optimization of concentration, additives and solvents, the process parameters are transferred to both, p‐ and n‐doped GaAs‐based nanowire structures. The influence of surface functionalization on the electrical behavior of the nanowires is determined by current–voltage characteristics. Based on the experimental data, a bonding mechanism for the alkanethiol onto the semiconductor material is proposed and a model for describing surface depletion before and after functionalization is developed.