Cynthia Linaya Radiman

Phase inversion is used to prepare poly(vinylidene fluoride) (PVDF) microfiltration membranes by combining it with the hydrophilic polymer additive cellulose acetate (CA). For the filtration of methylene blue (MB) and acid yellow 17 (AY17), the effects of coagulant bath temperature (CBT) on the separation performance and antifouling properties are thoroughly investigated. SEM analysis shows that the membrane at higher CBT has a larger pore diameter than at lower CBT, resulting in differences in membrane surface hydrophilicity. It is found that the increase in surface hydrophilicity causes the permeability of PVDF/CA membranes to be higher at higher CBT than at lower CBT. Rejection values above 90% indicate that the membranes are more effective for MB separation at both lower and higher CBT. Otherwise, lower CBT provides better AC rejection than higher CBT. The Flux Recovery Ratio, which is higher at higher CBT, remains in the 75–95% range at lower CBT. As a result, lower CBT is better for membrane fouling resistance than higher CBT. In addition, the fouling observed at lower CBT is similar to the fouling observed at higher CBT, but lower CBT has a higher percentage of reversible fouling than higher CBT. The membranes with more reversible fouling are therefore easier to clean using the backwashing process. As a result, PVDF/CA membranes manufactured at lower CBT have better separation performance and antifouling characteristics than those manufactured at higher CBT.

Membrane technology has become an efficient technique in water treatment because of its high efficiency, low energy consumption, cost-effectiveness, and low env Membrane technology has become an efficient technique in water treatment because of its high efficiency, low energy consumption, cost-effectiveness, and low env

Kajian struktur dan degradasi termal pada membran hibrida poliviniliden fluorida (PVDF)/lempung bentonit (BNT) telah dilakukan. Penelitian ini bertujuan mengetahui pengaruh penambahan BNT terhadap pembentukan fasa PVDF dan sifat termalnya. Membran hibrida PVDF/lempung BNT dibuat dengan metode inversi fasa. Membran yang dihasilkan dikarakterisasi dengan attenuated total reflectance fourier transform infrared (ATR-FTIR), x-ray diffraction (XRD), dan differential scanning calorimetry (DSC). Hasil penelitian menunjukkan membran PVDF/BNT memiliki struktur polimorf PVDF fasa α dan β yang terkonfirmasi dari data FTIR dan XRD. Data DSC menunjukkan penurunan nilai titik leleh (Tm) dengan penambahan BNT, dan dengan rentang suhu pelelehan yang lebih kecil. Kristalisasi PVDF terjadi secara isothermal dan adanya BNT menghasilkan titik kristalisasi (Tc) pada suhu yang lebih tinggi dibandingkan membran PVDF murni. Analisis termal dengan DSC memberikan informasi komprehensif pelelehan dan kristalisasi dari polimorf PVDF pada matriks membran.Effect of Bentonite toward Polymorph Phase Formation and Thermal Properties of Polyvinylidene Fluoride/Bentonite Hybrid Membranes. The study of the structure and thermal properties of PVDF/bentonite (BNT) hybrid membranes has been carried out. This study aims to determine the effect of BNT addition on the phase formation and thermal properties of the PVDF. In this study, PVDF/BNT hybrid membranes were prepared through the phase inversion method. The resulting membrane was characterized by Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR), x-ray diffraction (XRD), and differential scanning calorimetry (DSC). The results showed that the PVDF/BNT membrane has a PVDF polymorph structure with α and β phases confirmed by FTIR and XRD data. The DSC data showed that the addition of BNT decrease of the melting point (Tm) and with a smaller melting temperature range. PVDF polymorph crystallization occurs isothermally and the presence of BNT produces a crystallization point (Tc) at a higher temperature than pristine PVDF membrane. Thermal analysis with DSC provides comprehensive information on melting and crystallization of PVDF polymorphs in the membrane matrix.

Direct Methanol Fuel Cells (DMFCs) is one of the most promising alternative energy resources to meet human energy needs. DMFCs is fuel cells that use polymer membranes as the electrolytes to transfer the protons from anode to cathode. The characteristics of those two types of membranes in ion exchange capacity (IEC) and degree of swelling (swelling) have shown a very important role of water in the proton transfer. However, the mechanism of interaction between the repeating units of the polymer with water molecules has not been studied in depth. Computational methods can be used to study such interactions as well as the transfer of protons. To examine the transfer of protons in the membrane, studies of computing via electronic structure calculations, geometry optimization, interaction inter/intra molecular, as well as the hydration process and transfer of protons in the sulfonated nata-de-coco membranes (NDCS) has been conducted in this work. All calculations were performed using DFT with B3LYP functional and basis set 6-311G(d). The repeating units of the membranes were optimized (n=1,2,...,5), to obtain the structure with minimum energy. The optimized structure was then interacted with one water molecule in the same position to study the effect of chain length on its interaction strength with water molecules. The thermodynamic and proton dissociation parameters was calculated by adding n water molecules (n=1,2, …,10) to determine the hydration process and the proton transfer on the membranes. The calculations showed that for interactions with water, the polymer structure in NDCS can be represented/modeled by two repeating units. Therefore, the hydration process and transfer of protons in the membranes were studied by adding n water molecules gradually into the two repeating units. The results showed that the proton dissociation process in NDCS membrane started with the addition of two molecules of water. The presence of water molecules promoted the proton dissociation in the -SO3H groups to form SO3- and H3O+ ions, which further formed Zundel ions and Eigen ions. The energy profile of proton transfer showed that the barrier energy was 58.13 kcal/mol for NDCS-5(H2O). Its thermodynamic parameters, the calculation showed that the interaction energy (ΔE), the enthalpy change (ΔH) and the Gibbs free energy (ΔG) to its interaction with n water molecules (n=1,2,…,10) in NDCS are getting more negative. This indicated that the interaction with water molecule is stronger. So, based on these results, it can be concluded that the computational calculations using DFT method at B3LYP functional and 6-311G(d) basis set can be used to describe the process of hydration and proton transfer in the interactions in the polymer electrolyte membrane (NDCS membrane)

This study aims to study the conformation, the hydrogen bond network, and the stabilities of all the possible intermolecular interactions in phosphorylated nata de coco membrane with water (NDCF-(H2O)n, n = 1-5). Analysis of natural bond orbital (NBO) was performed to measure the relative strength of the hydrogen bonding interactions, charge transfer, particularly the interactions of n-σ * O-H and to take into account the effect on the stabilities of the molecular structure. All calculation were performed using density functional theory (DFT) method, at B3LYP functional level of theory and 6-311 G** basis set. The charge transfer between the lone pair of a proton acceptor to the anti-bonding orbital of the proton donor provides the substantial to the stabilization of the hydrogen bonds. Interaction between NDCF and (H2O)5 was strongest with the stabilization energy of 37.73 kcal/mol, that indicate the ease of donating lone pair electrons. The contributions of each hydrogen bond to the stability of the complex have been analyzed.