Naresh Kumar Thipparapu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Naresh Kumar Thipparapu has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Yu Wang
Optoelectronics Research Centre (ORC), University of Southampton, Southampton, U.K.
13 shared publications - Andrey A. Umnikov
G.G. Devyatykh Institute of Chemistry of High-Purity Substances of the Russian Academy of Sciences
12 shared publications - David John Richardson
School of Biological Sciences, University of East Anglia, Norwich Research Park, Norwich NR4 7TJ, United Kingdom
12 shared publications - Jayanta Kumar Sahu
Optoelectronics Research Centre, University of Southampton, Highfield, Southampton, SO17 1BJ, UK
12 shared publications - Periklis Petropoulos
Optoelectronics Research Centre, University of Southampton, Southampton, UK
10 shared publications - Kyle R. H. Bottrill
Optoelectronics Research Centre, University of Southampton, Southampton, U.K.
8 shared publications
Latest Publications
- Open Access
- 18 August 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (18) , 32189-32203
Experimental demonstration of single-span 100-km O-band 4×50-Gb/s CWDM direct-detection transmission
We report on what is to the best of our knowledge the longest 50-Gb/s/λ O-band wavelength-division multiplexed (WDM) transmission. A pair of in-house built bismuth-doped fiber amplifiers (BDFAs) and the use of Kramers-Kronig detection-assisted single-sideband transmission are adopted to overcome the fiber loss and chromatic dispersion, respectively, in a reach-extended O-band coarse WDM (CWDM) system with a channel spacing of ∼10 nm. Through experiments on an amplified 4×50-Gb/s/λ direct-detection system based on booster and pre-amp BDFAs, we show the superior performance of single-sideband transmission in terms of both optical signal-to-noise ratio sensitivity and uniformity in performance amongst CWDM channels relative to double-sideband transmission after both 75-km and 100-km lengths of single-mode fiber. As a result, up to 100-km reach with comparable performance at all 50-Gb/s channels was achieved without the need for in-line optical amplification.
- 18 August 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (18) , 32189-32203
Open AccessExperimental demonstration of single-span 100-km O-band 4×50-Gb/s CWDM direct-detection transmission
We report on what is to the best of our knowledge the longest 50-Gb/s/λ O-band wavelength-division multiplexed (WDM) transmission. A pair of in-house built bismuth-doped fiber amplifiers (BDFAs) and the use of Kramers-Kronig detection-assisted single-sideband transmission are adopted to overcome the fiber loss and chromatic dispersion, respectively, in a reach-extended O-band coarse WDM (CWDM) system with a channel spacing of ∼10 nm. Through experiments on an amplified 4×50-Gb/s/λ direct-detection system based on booster and pre-amp BDFAs, we show the superior performance of single-sideband transmission in terms of both optical signal-to-noise ratio sensitivity and uniformity in performance amongst CWDM channels relative to double-sideband transmission after both 75-km and 100-km lengths of single-mode fiber. As a result, up to 100-km reach with comparable performance at all 50-Gb/s channels was achieved without the need for in-line optical amplification.
- 3 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 28 (4) , 1-10
ML-Assisted Equalization for 50-Gb/s/λ O-Band CWDM Transmission Over 100-km SMF
We propose and demonstrate a bidirectional Vanilla recurrent neural network (Vanilla-RNN) based equalization scheme for O-band coarse wavelength division multiplexed (CWDM) transmission. Based on a 4 × 50-Gb/s intensity modulation and direct detection (IM/DD) system, we demonstrate the significantly better bit error rate (BER) performance of the Vanilla-RNN scheme over the conventional decision feedback equalizer (DFE) for both Nyquist on-off keying (OOK) and Nyquist 4-ary pulse amplitude modulation (PAM4) formats. It is shown that the Vanilla-RNN equalizer is capable of compensating for both linear and nonlinear impairments induced by the transceiver and the single-mode fiber (SMF). As a result, up to 100-km and 75-km SMF transmission can be achieved for OOK and PAM4 transmission, respectively. Furthermore, through the comparison with other equalization schemes, including the linear equalizer, 3 rd -order Volterra equalizer, and Volterra+DFE, it is demonstrated that the Vanilla-RNN equalizer achieves the best BER performance. In the meantime, it also exhibits lower implementation complexity when compared to Volterra-based schemes. Our results show that the Vanilla-RNN scheme is a viable solution for realizing simple and effective equalization. This work serves as an exploration and offers useful insights for future implementations of reach-extended O-band CWDM IM/DD systems.
- 3 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Quantum Electronics
- Vol. 28 (4) , 1-10
ML-Assisted Equalization for 50-Gb/s/λ O-Band CWDM Transmission Over 100-km SMF
We propose and demonstrate a bidirectional Vanilla recurrent neural network (Vanilla-RNN) based equalization scheme for O-band coarse wavelength division multiplexed (CWDM) transmission. Based on a 4 × 50-Gb/s intensity modulation and direct detection (IM/DD) system, we demonstrate the significantly better bit error rate (BER) performance of the Vanilla-RNN scheme over the conventional decision feedback equalizer (DFE) for both Nyquist on-off keying (OOK) and Nyquist 4-ary pulse amplitude modulation (PAM4) formats. It is shown that the Vanilla-RNN equalizer is capable of compensating for both linear and nonlinear impairments induced by the transceiver and the single-mode fiber (SMF). As a result, up to 100-km and 75-km SMF transmission can be achieved for OOK and PAM4 transmission, respectively. Furthermore, through the comparison with other equalization schemes, including the linear equalizer, 3 rd -order Volterra equalizer, and Volterra+DFE, it is demonstrated that the Vanilla-RNN equalizer achieves the best BER performance. In the meantime, it also exhibits lower implementation complexity when compared to Volterra-based schemes. Our results show that the Vanilla-RNN scheme is a viable solution for realizing simple and effective equalization. This work serves as an exploration and offers useful insights for future implementations of reach-extended O-band CWDM IM/DD systems.
- 27 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (13) , 711-714
Widely Tunable Actively Mode-Locked Bi-Doped Fiber Laser Operating in the O-Band
Here, we propose an all-fiber actively mode-locked Bismuth (Bi)-doped fiber laser based on the use of an acousto-optic modulator. The mode-locked Bi-doped fiber laser produces 13ns pulses with a repetition rate of 1.683MHz at 1340nm. Higher harmonic mode-locking is achieved simply by changing the operating frequency of the acousto-optic modulator. The output power of the laser is 7mW and this is further amplified to 101mW using an external Bi-doped fiber amplifier. A peak power of 4.6W with a pulse energy of 60nJ is achieved after the master oscillator power amplifier. The stability of the laser is studied using an RF spectrum analyzer and an SNR of more than 60dB at the fundamental frequency of 1.683MHz was recorded. Furthermore, wavelength tuning of the Bi-doped fiber laser is explored and demonstrated from 1300 to 1370nm.
- 27 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (13) , 711-714
Widely Tunable Actively Mode-Locked Bi-Doped Fiber Laser Operating in the O-Band
Here, we propose an all-fiber actively mode-locked Bismuth (Bi)-doped fiber laser based on the use of an acousto-optic modulator. The mode-locked Bi-doped fiber laser produces 13ns pulses with a repetition rate of 1.683MHz at 1340nm. Higher harmonic mode-locking is achieved simply by changing the operating frequency of the acousto-optic modulator. The output power of the laser is 7mW and this is further amplified to 101mW using an external Bi-doped fiber amplifier. A peak power of 4.6W with a pulse energy of 60nJ is achieved after the master oscillator power amplifier. The stability of the laser is studied using an RF spectrum analyzer and an SNR of more than 60dB at the fundamental frequency of 1.683MHz was recorded. Furthermore, wavelength tuning of the Bi-doped fiber laser is explored and demonstrated from 1300 to 1370nm.
- 17 May 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (15) , 4383-4390
Numerical and experimental study on the impact of chromatic dispersion on O-band direct-detection transmission
The recent emergence of efficient O-band amplification technologies has enabled the consideration of O-band transmission beyond short reach. Despite the O-band being a low chromatic dispersion (CD) window, the impact of CD will become increasingly significant when extending the reach of direct-detection (DD) systems. In this work, we first numerically investigate the 3-dB bandwidth of single-mode fibers (SMF) and the CD-restricted transmission reach in intensity-modulation DD systems, confirming the significant difference between low- and high-dispersion O-band wavelengths. We then carry out experimental transmission studies over SMF for distances of up to 70 km at two different wavelengths, the low-dispersion 1320 nm and the more dispersive 1360 nm, enabled by the use of an O-band bismuth-doped fiber amplifier as a preamplifier at the receiver. We compare three 50-Gb/s optical DD formats, namely, Nyquist on-off keying (OOK), Nyquist 4-ary pulse amplitude modulation (PAM4) and Kramers–Kronig detection-assisted single-sideband quadrature phase shift keying (KK-QPSK) half-cycle subcarrier modulation. Our results show that at both wavelengths, OOK and QPSK exhibit better bit error rate performance than PAM4. When transmitting over 70-km of SMF at the less dispersive wavelength of 1320 nm, 50-Gb/s OOK modulation offers more than 1.5-dB optical power sensitivity improvement at the photodiode (PD) compared to 50-Gb/s QPSK. Conversely, at 1360 nm, the required optical power to the PD can be reduced by more than 3 dB by using QPSK instead of OOK.
- 17 May 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (15) , 4383-4390
Numerical and experimental study on the impact of chromatic dispersion on O-band direct-detection transmission
The recent emergence of efficient O-band amplification technologies has enabled the consideration of O-band transmission beyond short reach. Despite the O-band being a low chromatic dispersion (CD) window, the impact of CD will become increasingly significant when extending the reach of direct-detection (DD) systems. In this work, we first numerically investigate the 3-dB bandwidth of single-mode fibers (SMF) and the CD-restricted transmission reach in intensity-modulation DD systems, confirming the significant difference between low- and high-dispersion O-band wavelengths. We then carry out experimental transmission studies over SMF for distances of up to 70 km at two different wavelengths, the low-dispersion 1320 nm and the more dispersive 1360 nm, enabled by the use of an O-band bismuth-doped fiber amplifier as a preamplifier at the receiver. We compare three 50-Gb/s optical DD formats, namely, Nyquist on-off keying (OOK), Nyquist 4-ary pulse amplitude modulation (PAM4) and Kramers–Kronig detection-assisted single-sideband quadrature phase shift keying (KK-QPSK) half-cycle subcarrier modulation. Our results show that at both wavelengths, OOK and QPSK exhibit better bit error rate performance than PAM4. When transmitting over 70-km of SMF at the less dispersive wavelength of 1320 nm, 50-Gb/s OOK modulation offers more than 1.5-dB optical power sensitivity improvement at the photodiode (PD) compared to 50-Gb/s QPSK. Conversely, at 1360 nm, the required optical power to the PD can be reduced by more than 3 dB by using QPSK instead of OOK.
- Open Access
- 4 May 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (10) , 15345-15355
Experimental characterization of an o-band bismuth-doped fiber amplifier
The recent emergence of bismuth-doped fiber amplifiers (BDFAs) offers the potential to transmit high-speed WDM signals over long distances in the O-band spectral region, thereby greatly enhancing the scope of systems utilizing these wavelengths. In this paper, we present a comprehensive experimental study on several basic characteristics of an O-band BDFA based on a phosphosilicate optical fiber, including the frequency-dependent noise figure, gain tilt (static and dynamic), transient response, and polarization dependent gain. We discuss our findings and their implications on the use of BDFA technology in high bit-rate multichannel systems.
- 4 May 2021
- Published by Optica Publishing Group in Optics Express
- Vol. 29 (10) , 15345-15355
Open AccessExperimental characterization of an o-band bismuth-doped fiber amplifier
The recent emergence of bismuth-doped fiber amplifiers (BDFAs) offers the potential to transmit high-speed WDM signals over long distances in the O-band spectral region, thereby greatly enhancing the scope of systems utilizing these wavelengths. In this paper, we present a comprehensive experimental study on several basic characteristics of an O-band BDFA based on a phosphosilicate optical fiber, including the frequency-dependent noise figure, gain tilt (static and dynamic), transient response, and polarization dependent gain. We discuss our findings and their implications on the use of BDFA technology in high bit-rate multichannel systems.
- Open Access
- 1 January 2021
- Published by Optica Publishing Group
- p. W1B.2
Experimental Demonstration of 50-Gb/s/Z O-band CWDM Direct-Detection Transmission over 100-km SMF
We demonstrate the first single-sideband 50-Gb/sA coarse WDM direct-detection transmission in the O-band. It is shown that the Kramers-Kronig-detection assisted single-sideband transmission exhibits significant OSNR sensitivity improvements over double-sideband transmission, enabling up to 100-km reach.
- 1 January 2021
- Published by Optica Publishing Group
- p. W1B.2
Open AccessExperimental Demonstration of 50-Gb/s/Z O-band CWDM Direct-Detection Transmission over 100-km SMF
We demonstrate the first single-sideband 50-Gb/sA coarse WDM direct-detection transmission in the O-band. It is shown that the Kramers-Kronig-detection assisted single-sideband transmission exhibits significant OSNR sensitivity improvements over double-sideband transmission, enabling up to 100-km reach.
- 1 January 2021
- Published by Optica Publishing Group
- p. STh1F.3
Performance-enhanced Amplified O-band WDM Transmission using Machine Learning based Equalization
We investigate the performance of a machine learning-based equalization in an amplified 4×50-Gb/s O-band WDM system. The results show that the scheme offers significant receiver sensitivity improvements over decision-feedback equalization, especially at more dispersive wavelengths.
- 1 January 2021
- Published by Optica Publishing Group
- p. STh1F.3
Performance-enhanced Amplified O-band WDM Transmission using Machine Learning based Equalization
We investigate the performance of a machine learning-based equalization in an amplified 4×50-Gb/s O-band WDM system. The results show that the scheme offers significant receiver sensitivity improvements over decision-feedback equalization, especially at more dispersive wavelengths.
- 24 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (3) , 795-800
Ultra-Broadband Bismuth-Doped Fiber Amplifier Covering a 115-nm Bandwidth in the O and E Bands
In this article, we experimentally demonstrate an all-fiber optical amplifier using Bi-doped phosphosilicate fiber (BPSF) operating in both the O-band and the E-band, providing >20 dB gain from 1345 to 1460 nm for an input signal power of −23 dBm. A maximum gain of 31 dB with a noise figure (NF) of 4.8 dB was achieved at 1420 nm for −23 dBm input signal, whereas for an input signal power of −10 dBm it was 26 dB with a NF of 5.3 dB. The in-band OSNR of the proposed Bi-doped fiber amplifier (BDFA) was >22 dB from 1345 to 1460 nm for a −23 dBm input signal. The gain coefficient was found to be 0.04 dB/mW for a −23 dBm input signal. Also, the temperature dependent gain and NF performance of the BDFA within −40 to +60 °C were characterized. The temperature-dependent-gain (TDG) coefficient for a −23 dBm input signal was found to be −0.015 dB/°C at a signal wavelength of 1420 nm where the BDFA gain is maximum, while for an input signal power of −10 dBm it was −0.01 dB/°C at 1420 nm. The TDG coefficient of the proposed BDFA from 1350–1460 nm was in the range from −0.079 to −0.008 dB/°C. The BDFA gain and NF performance were also measured and compared using BPSFs with different unsaturable loss (UL) characteristics.
- 24 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 39 (3) , 795-800
Ultra-Broadband Bismuth-Doped Fiber Amplifier Covering a 115-nm Bandwidth in the O and E Bands
In this article, we experimentally demonstrate an all-fiber optical amplifier using Bi-doped phosphosilicate fiber (BPSF) operating in both the O-band and the E-band, providing >20 dB gain from 1345 to 1460 nm for an input signal power of −23 dBm. A maximum gain of 31 dB with a noise figure (NF) of 4.8 dB was achieved at 1420 nm for −23 dBm input signal, whereas for an input signal power of −10 dBm it was 26 dB with a NF of 5.3 dB. The in-band OSNR of the proposed Bi-doped fiber amplifier (BDFA) was >22 dB from 1345 to 1460 nm for a −23 dBm input signal. The gain coefficient was found to be 0.04 dB/mW for a −23 dBm input signal. Also, the temperature dependent gain and NF performance of the BDFA within −40 to +60 °C were characterized. The temperature-dependent-gain (TDG) coefficient for a −23 dBm input signal was found to be −0.015 dB/°C at a signal wavelength of 1420 nm where the BDFA gain is maximum, while for an input signal power of −10 dBm it was −0.01 dB/°C at 1420 nm. The TDG coefficient of the proposed BDFA from 1350–1460 nm was in the range from −0.079 to −0.008 dB/°C. The BDFA gain and NF performance were also measured and compared using BPSFs with different unsaturable loss (UL) characteristics.
- 9 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (22) , 1443-1446
Tunable CW Bi-Doped Fiber Laser System From 1320 to 1370 nm Using a Fiber Bragg Grating
Here we present a fully fiberized Bi-doped ring laser incorporating a fiber Bragg grating (FBG) operating at a wavelength of 1340nm, which provides 172mW of continuous-wave output power with a slope efficiency of 35%. In addition, we demonstrate a wavelength-tunable version of the laser, which can be tuned from 1320nm to 1370nm by employing a home-made mechanically tunable FBG. Within the whole 50nm tuning band the laser maintains the output power of more than 100mW and the slope efficiency of more than 25%. A maximum output power of 165mW is achieved over the wavelength range of 1330-1340nm. The linewidth of tunable laser is 0.04nm.
- 9 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 32 (22) , 1443-1446
Tunable CW Bi-Doped Fiber Laser System From 1320 to 1370 nm Using a Fiber Bragg Grating
Here we present a fully fiberized Bi-doped ring laser incorporating a fiber Bragg grating (FBG) operating at a wavelength of 1340nm, which provides 172mW of continuous-wave output power with a slope efficiency of 35%. In addition, we demonstrate a wavelength-tunable version of the laser, which can be tuned from 1320nm to 1370nm by employing a home-made mechanically tunable FBG. Within the whole 50nm tuning band the laser maintains the output power of more than 100mW and the slope efficiency of more than 25%. A maximum output power of 165mW is achieved over the wavelength range of 1330-1340nm. The linewidth of tunable laser is 0.04nm.
- 17 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (10) , 2849-2857
Multi-Band Direct-Detection Transmission Over an Ultrawide Bandwidth Hollow-Core NANF
In this paper, we report high-speed multi-band direct-detection (DD) transmission over a hollow-core nested antiresonant nodeless fiber (NANF). Thanks to the ultrawide bandwidth of the NANF, we demonstrate dual-band transmission across the O- and C-bands over a ~1-km length of a hollow-core fiber for the first time. Eight wavelength-division multiplexed (WDM) channels were transmitted using 100-Gb/s/λ Nyquist 4-ary pulse-amplitude modulation (PAM4) signals, which to the best of our knowledge, is the highest aggregate capacity ever transmitted in a DD hollow-core fiber-based transmission system. Optical pre-amplification was adopted for signal reception in both bands, achieved using an in-house built bismuth-doped optical fibre amplifier (BDFA) and a commercial erbium-doped fiber amplifier (EDFA) in the O- and C-band, respectively. We further demonstrate beyond 100-Gb/s/λ adaptively-loaded discrete multitone (DMT) transmission over the S+C+L-bands using the same NANF, without the use of optical amplification. Our experiments show that apart from fiber loss, the use of the NANF did not introduce any additional transmission penalties. The demonstrated results validate the ultrawide bandwidth and excellent modal purity of the fabricated NANF, which allow beyond 100-Gb/s/λ penalty-free transmission over multiple bands, highlighting the potential of this fiber technology for high-speed short- to intermediate-reach applications.
- 17 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 38 (10) , 2849-2857
Multi-Band Direct-Detection Transmission Over an Ultrawide Bandwidth Hollow-Core NANF
In this paper, we report high-speed multi-band direct-detection (DD) transmission over a hollow-core nested antiresonant nodeless fiber (NANF). Thanks to the ultrawide bandwidth of the NANF, we demonstrate dual-band transmission across the O- and C-bands over a ~1-km length of a hollow-core fiber for the first time. Eight wavelength-division multiplexed (WDM) channels were transmitted using 100-Gb/s/λ Nyquist 4-ary pulse-amplitude modulation (PAM4) signals, which to the best of our knowledge, is the highest aggregate capacity ever transmitted in a DD hollow-core fiber-based transmission system. Optical pre-amplification was adopted for signal reception in both bands, achieved using an in-house built bismuth-doped optical fibre amplifier (BDFA) and a commercial erbium-doped fiber amplifier (EDFA) in the O- and C-band, respectively. We further demonstrate beyond 100-Gb/s/λ adaptively-loaded discrete multitone (DMT) transmission over the S+C+L-bands using the same NANF, without the use of optical amplification. Our experiments show that apart from fiber loss, the use of the NANF did not introduce any additional transmission penalties. The demonstrated results validate the ultrawide bandwidth and excellent modal purity of the fabricated NANF, which allow beyond 100-Gb/s/λ penalty-free transmission over multiple bands, highlighting the potential of this fiber technology for high-speed short- to intermediate-reach applications.