Tatiana Galinska
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tatiana Galinska has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Dmytro Kochkarev
National University of Water and Environment Engineering
14 shared publications - Taliat Azizov
Sumy National Agrarian University
12 shared publications - Dmytro Ovsii
National University "Yuri Kondratyuk Poltava Polytechnic
7 shared publications - Anna Azizova
National University “Yurii Kondratyuk Poltava Polytechnic
4 shared publications - Mukhlis Hajiyev
Azerbaijan University of Architecture and Construction
4 shared publications - Oleksandra Ovsii
National University «Yuri Kondratyuk Poltava Polytechnic
4 shared publications
Latest Publications
- Open Access
- 1 June 2026
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1638 (1)
Estimation of modal contributions in impulse load calculations
The article presents an analytical generalisation of the classical impulse method for calculating the dynamic response of mechanical systems to explosive and shock loads. The main focus is on accounting for the influence of the impulse duration-to-natural-period ratio, thereby extending the applicability of the impulse approach to medium-duration loads. Based on the exact solution of the equation of motion of a single-mass system without damping using the Duhamel integral for a descending triangular impulse, a generalised analytical formula for determining the maximum amplitude of displacements is obtained. A dimensionless dynamic correction coefficient is proposed that describes the interaction between the impulse’s temporal structure and the system’s natural oscillation mode. Limit transitions to the classical impulse and quasi-static modes are shown at the corresponding values of the matching parameter. The use of the invariant of total mechanical energy as a characteristic of the efficiency of excitation of natural vibration modes is separately justified. On this basis, a method for determining the required number of modes for multi-mass systems in the analysis of explosive loads is proposed, accounting for the zone of insignificant influence of the explosive-pulse spectrum. The results obtained can be used to simplify engineering calculations for structural elements under short-term dynamic loading and to develop modal analysis methods further.
- 1 June 2026
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1638 (1)
Open AccessEstimation of modal contributions in impulse load calculations
The article presents an analytical generalisation of the classical impulse method for calculating the dynamic response of mechanical systems to explosive and shock loads. The main focus is on accounting for the influence of the impulse duration-to-natural-period ratio, thereby extending the applicability of the impulse approach to medium-duration loads. Based on the exact solution of the equation of motion of a single-mass system without damping using the Duhamel integral for a descending triangular impulse, a generalised analytical formula for determining the maximum amplitude of displacements is obtained. A dimensionless dynamic correction coefficient is proposed that describes the interaction between the impulse’s temporal structure and the system’s natural oscillation mode. Limit transitions to the classical impulse and quasi-static modes are shown at the corresponding values of the matching parameter. The use of the invariant of total mechanical energy as a characteristic of the efficiency of excitation of natural vibration modes is separately justified. On this basis, a method for determining the required number of modes for multi-mass systems in the analysis of explosive loads is proposed, accounting for the zone of insignificant influence of the explosive-pulse spectrum. The results obtained can be used to simplify engineering calculations for structural elements under short-term dynamic loading and to develop modal analysis methods further.
- Open Access
- 1 May 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3251 (1)
Analytical determination of the deformability of reinforced concrete structures under torsion based on an energy invariant
The present study is devoted to solving a fundamental problem of structural mechanics – namely, the determination of the deformability of reinforced concrete structures at the serviceability stage while accounting for physical nonlinearity and crack formation. The relevance of the research is driven by the need to move from empirical stiffness evaluation methods toward analytical models based on the principles of energy balance and fracture mechanics. The paper proposes the concept of a complete energy invariant of shear deformation, which makes it possible to determine the effective torsional stiffness through harmonic averaging of the sectional stiffness at crack planes and in the regions between cracks. The key scientific novelty lies in deriving the crack spacing based on an energy criterion: a new crack forms when the accumulated excess strain energy of the reinforcement in the localization zone becomes equal to the fracture work of concrete. Special attention is given to the refined modeling of stress distribution in reinforcement. Unlike classical “pull-out” models, the authors employ the block symmetry law, which allows stresses to be described by a hyperbolic cosine function, taking into account both the adhesive component of bond and the deformation coefficient. This approach ensures an accurate representation of the behavior of cracked elements in the tension zone. At the theoretical level, the role of the dowel action of reinforcement is substantiated as a decisive factor governing torsional resistance after crack opening. An analytical expression for stiffness incorporating the dowel effect is derived, in which the reinforcing bar is modeled as a beam on an elastic foundation with due consideration of the concrete cover thickness. The integration of the dowel effect into the overall model significantly improves the accuracy of stiffness prediction. The practical significance of the study lies in the applicability of the proposed relationships to the design of high-rise buildings and long-span structures, where accurate determination of torsional stiffness is critical for reliable internal force assessment, structural stability, and deformation control.
- 1 May 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3251 (1)
Open AccessAnalytical determination of the deformability of reinforced concrete structures under torsion based on an energy invariant
The present study is devoted to solving a fundamental problem of structural mechanics – namely, the determination of the deformability of reinforced concrete structures at the serviceability stage while accounting for physical nonlinearity and crack formation. The relevance of the research is driven by the need to move from empirical stiffness evaluation methods toward analytical models based on the principles of energy balance and fracture mechanics. The paper proposes the concept of a complete energy invariant of shear deformation, which makes it possible to determine the effective torsional stiffness through harmonic averaging of the sectional stiffness at crack planes and in the regions between cracks. The key scientific novelty lies in deriving the crack spacing based on an energy criterion: a new crack forms when the accumulated excess strain energy of the reinforcement in the localization zone becomes equal to the fracture work of concrete. Special attention is given to the refined modeling of stress distribution in reinforcement. Unlike classical “pull-out” models, the authors employ the block symmetry law, which allows stresses to be described by a hyperbolic cosine function, taking into account both the adhesive component of bond and the deformation coefficient. This approach ensures an accurate representation of the behavior of cracked elements in the tension zone. At the theoretical level, the role of the dowel action of reinforcement is substantiated as a decisive factor governing torsional resistance after crack opening. An analytical expression for stiffness incorporating the dowel effect is derived, in which the reinforcing bar is modeled as a beam on an elastic foundation with due consideration of the concrete cover thickness. The integration of the dowel effect into the overall model significantly improves the accuracy of stiffness prediction. The practical significance of the study lies in the applicability of the proposed relationships to the design of high-rise buildings and long-span structures, where accurate determination of torsional stiffness is critical for reliable internal force assessment, structural stability, and deformation control.
- 15 July 2025
- Published by Springer Nature
- p. 260-271
Experience in the Use of Solid Industrial Waste in Geotechnics
- 15 July 2025
- Published by Springer Nature
- p. 260-271
Experience in the Use of Solid Industrial Waste in Geotechnics
- 15 July 2025
- Published by Springer Nature
- p. 77-85
The Formation of Criteria for Evaluation of the Technical Condition Damaged of Corroded Sections of I-Beams
- 15 July 2025
- Published by Springer Nature
- p. 77-85
The Formation of Criteria for Evaluation of the Technical Condition Damaged of Corroded Sections of I-Beams
- 15 July 2025
- Published by Springer Nature
- p. 142-151
Basic Positions of Models of Adhesion Between Concrete and Reinforcement Based on Average Tangential Stresses
- 15 July 2025
- Published by Springer Nature
- p. 142-151
Basic Positions of Models of Adhesion Between Concrete and Reinforcement Based on Average Tangential Stresses
- Open Access
- 18 December 2024
- Published by Yuri Kondratyuk Poltava Polytechnic in Збірник наукових праць Галузеве машинобудування будівництво/ Academic journal Industrial Machine Building Civil Engineering
- Vol. 2 (63) , 33-38
Strengthening of the cross-section of steel i-beams in the tension zone: a review of scientific research
The article reviews scientific research on methods and means of strengthening steel beam structural elements by increasing (building up) cross-sections using additional elements made of steel rolled profiles, plates, reinforcing bars and plates made of polymeric materials. The main conclusions and directions of further scientific research on effective methods and means of strengthening steel beam structural elements by increasing (building up) their cross-sections, which have the potential for widespread use in the repair and reconstruction of buildings and structures, are substantiated.
- 18 December 2024
- Published by Yuri Kondratyuk Poltava Polytechnic in Збірник наукових праць Галузеве машинобудування будівництво/ Academic journal Industrial Machine Building Civil Engineering
- Vol. 2 (63) , 33-38
Open AccessStrengthening of the cross-section of steel i-beams in the tension zone: a review of scientific research
The article reviews scientific research on methods and means of strengthening steel beam structural elements by increasing (building up) cross-sections using additional elements made of steel rolled profiles, plates, reinforcing bars and plates made of polymeric materials. The main conclusions and directions of further scientific research on effective methods and means of strengthening steel beam structural elements by increasing (building up) their cross-sections, which have the potential for widespread use in the repair and reconstruction of buildings and structures, are substantiated.
- 9 August 2024
- Published by Springer Nature
- p. 245-256
Calculation of Buildings and Structures for Air Blasts Using Explosion Accelerograms
- 9 August 2024
- Published by Springer Nature
- p. 245-256
Calculation of Buildings and Structures for Air Blasts Using Explosion Accelerograms
- 6 March 2024
- Published by Springer Nature
- p. 50-58
Calculation of Enclosures of Defence Structures Based on the Quasi-static Method
- 6 March 2024
- Published by Springer Nature
- p. 50-58
Calculation of Enclosures of Defence Structures Based on the Quasi-static Method