Alexandr Laposa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alexandr Laposa has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Jiri Kroutil
Department of Microelectronics, Czech Technical University in Prague, Technicka 2,166 27 Prague, Czech Republic
12 shared publications - Marina Davydova
Czech Technical University in Prague
6 shared publications - Jan Voves
Faculty of Electrical Engineering, Czech Technical University in Prague, Prague, Czech Republic, EU
5 shared publications - Josef Nahlik
Department of Microelectronics, Czech Technical University in Prague, Technicka 2,166 27 Prague, Czech Republic
5 shared publications Miroslav Husak
Department of Microelectronics, Czech Technical University in Prague, Technicka 2,166 27 Prague, Czech Republic
5 shared publicationsPavel Kulha
Department of Microelectronics, Czech Technical University, Prague, Czech Republic
5 shared publications
Latest Publications
- Open Access
- 1 January 2024
- Published by AMA Service GmbH
- p. 393-394
PT5.211 - NO2 Gas Sensor with Inkjet-Printed Zinc Oxide and Boron-Doped Diamond Layer
In this paper, we present a gas sensor with a sensing layer composed of Zinc Oxide (ZnO) and Boron-Doped Diamond (BDD) nanoparticles, deposited via inkjet printing technology. The sensor operates at room temperature and uses UV illumination to enhance its sensitivity and stabilize its responses. We investigated the gas-sensing capabilities of the ZnO-BDD layer for detecting low concentrations (ppm level) of NO2 in synthetic air.
- 1 January 2024
- Published by AMA Service GmbH
- p. 393-394
Open AccessPT5.211 - NO2 Gas Sensor with Inkjet-Printed Zinc Oxide and Boron-Doped Diamond Layer
In this paper, we present a gas sensor with a sensing layer composed of Zinc Oxide (ZnO) and Boron-Doped Diamond (BDD) nanoparticles, deposited via inkjet printing technology. The sensor operates at room temperature and uses UV illumination to enhance its sensitivity and stabilize its responses. We investigated the gas-sensing capabilities of the ZnO-BDD layer for detecting low concentrations (ppm level) of NO2 in synthetic air.
- Open Access
Gas Sensor with Different Morphology of PANI Layer
This work presents the design of a polymer-film-based sensor for gas detection. Different types of polyaniline are used as active layers. The advantages of resistive sensors with PANI layers are easy preparation and low production cost. At room temperature, polymer films have a high sensitivity to gas concentrations. The developed sensor works on the idea of electrical resistance shifting with gas concentration. Three different polymerization solutions are employed to synthesize the polyaniline (PANI) active layers (aqueous solution, sulfuric acid solution, and acetic acid solution). Active layers are evaluated in a controlled environment for their ability to detect ammonia, carbon monoxide, nitrogen monoxide, acetone, toluene, and relative humidity in synthetic air. PANI layers polymerized in acetic acid solutions exhibit good sensitivity toward ammonia.
Open AccessGas Sensor with Different Morphology of PANI Layer
This work presents the design of a polymer-film-based sensor for gas detection. Different types of polyaniline are used as active layers. The advantages of resistive sensors with PANI layers are easy preparation and low production cost. At room temperature, polymer films have a high sensitivity to gas concentrations. The developed sensor works on the idea of electrical resistance shifting with gas concentration. Three different polymerization solutions are employed to synthesize the polyaniline (PANI) active layers (aqueous solution, sulfuric acid solution, and acetic acid solution). Active layers are evaluated in a controlled environment for their ability to detect ammonia, carbon monoxide, nitrogen monoxide, acetone, toluene, and relative humidity in synthetic air. PANI layers polymerized in acetic acid solutions exhibit good sensitivity toward ammonia.
- Open Access
- 27 April 2022
- Published by Beilstein Institut in Beilstein Journal of Nanotechnology
- Vol. 13 (1) , 411-423
A chemiresistive sensor array based on polyaniline nanocomposites and machine learning classification
The selective detection of ammonia (NH3), nitrogen dioxide (NO2), carbon oxides (CO2 and CO), acetone ((CH3)2CO), and toluene (C6H5CH3) is investigated by means of a gas sensor array based on polyaniline nanocomposites. The array composed by seven different conductive sensors with composite sensing layers are measured and analyzed using machine learning. Statistical tools, such as principal component analysis and linear discriminant analysis, are used as dimensionality reduction methods. Five different classification methods, namely k-nearest neighbors algorithm, support vector machine, random forest, decision tree classifier, and Gaussian process classification (GPC) are compared to evaluate the accuracy of target gas determination. We found the Gaussian process classification model trained on features extracted from the data by principal component analysis to be a highly accurate method reach to 99% of the classification of six different gases.
- 27 April 2022
- Published by Beilstein Institut in Beilstein Journal of Nanotechnology
- Vol. 13 (1) , 411-423
Open AccessA chemiresistive sensor array based on polyaniline nanocomposites and machine learning classification
The selective detection of ammonia (NH3), nitrogen dioxide (NO2), carbon oxides (CO2 and CO), acetone ((CH3)2CO), and toluene (C6H5CH3) is investigated by means of a gas sensor array based on polyaniline nanocomposites. The array composed by seven different conductive sensors with composite sensing layers are measured and analyzed using machine learning. Statistical tools, such as principal component analysis and linear discriminant analysis, are used as dimensionality reduction methods. Five different classification methods, namely k-nearest neighbors algorithm, support vector machine, random forest, decision tree classifier, and Gaussian process classification (GPC) are compared to evaluate the accuracy of target gas determination. We found the Gaussian process classification model trained on features extracted from the data by principal component analysis to be a highly accurate method reach to 99% of the classification of six different gases.
- 11 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (3) , 1158-1165
Inkjet Seeded CVD-Grown Hydrogenated Diamond Gas Sensor Under UV-LED Illumination
- 11 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 20 (3) , 1158-1165
Inkjet Seeded CVD-Grown Hydrogenated Diamond Gas Sensor Under UV-LED Illumination
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1250-1253
An Inkjet Printed ZNO Based Gas Senor on a Flexible High Temperature Substrate for No2 Sensing
In this work we demonstrate the realization of a simple and low cost NO 2 gas sensor on a flexible polymer substrate. The sensor was fabricated using inkjet printing and hydrothermal growth and consists of a printed interdigital structure on which a sensitive zinc oxide layer was grown. The chosen growing process does not require an additional seed layer, which allows to directly grow the zinc oxide layer on the substrate. Furthermore, the operating temperature was intrinsically achieved with an inkjet printed heater, which is located at the backside of the sensor.
- 1 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1250-1253
An Inkjet Printed ZNO Based Gas Senor on a Flexible High Temperature Substrate for No2 Sensing
In this work we demonstrate the realization of a simple and low cost NO 2 gas sensor on a flexible polymer substrate. The sensor was fabricated using inkjet printing and hydrothermal growth and consists of a printed interdigital structure on which a sensitive zinc oxide layer was grown. The chosen growing process does not require an additional seed layer, which allows to directly grow the zinc oxide layer on the substrate. Furthermore, the operating temperature was intrinsically achieved with an inkjet printed heater, which is located at the backside of the sensor.
- 21 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (14) , 5587-5593
A High Sensitivity UV Photodetector With Inkjet Printed ZnO/Nanodiamond Active Layers
The single- and double-layered photodetectors based on ZnO and/or detonation nanodiamond (DND) have been developed via a sequential inkjet printing on the interdigital electrode (IDE) platform using a diamond and zinc oxide precursor ink. The morphological structure of the deposited materials was visualized and analyzed by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The crystalline configuration and structural quality of ZnO and nanodiamond were investigated by X-ray Diffraction (XRD) and Raman spectroscopy. The response, response time and recovery time were measured for different UV wavelengths (365, 385, and 405 nm), light intensities, temperatures and bias voltages. ZnO/DND structure shows more than 10 times higher response and faster reactivity in comparison with a single-layered photodetector. Photoresponsivity of the double-layered photodetector (ZnO/DND) is 0.35 A·W-1 whereas bare ZnO is about 0.039 A·W-1. The interaction between UV light and ZnO/DND grains was investigated by two dimensional Silvaco TCAD simulation.
- 21 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (14) , 5587-5593
A High Sensitivity UV Photodetector With Inkjet Printed ZnO/Nanodiamond Active Layers
The single- and double-layered photodetectors based on ZnO and/or detonation nanodiamond (DND) have been developed via a sequential inkjet printing on the interdigital electrode (IDE) platform using a diamond and zinc oxide precursor ink. The morphological structure of the deposited materials was visualized and analyzed by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The crystalline configuration and structural quality of ZnO and nanodiamond were investigated by X-ray Diffraction (XRD) and Raman spectroscopy. The response, response time and recovery time were measured for different UV wavelengths (365, 385, and 405 nm), light intensities, temperatures and bias voltages. ZnO/DND structure shows more than 10 times higher response and faster reactivity in comparison with a single-layered photodetector. Photoresponsivity of the double-layered photodetector (ZnO/DND) is 0.35 A·W-1 whereas bare ZnO is about 0.039 A·W-1. The interaction between UV light and ZnO/DND grains was investigated by two dimensional Silvaco TCAD simulation.
- 2 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 18 (9) , 3759-3766
Performance Evaluation of Low-Cost Flexible Gas Sensor Array With Nanocomposite Polyaniline Films
The aim of this paper is to present the design of a sensor array based on a single substrate with various composite polymer films as active layers for gas detection. A low power, four element flexible sensor platform with heater and temperature sensor was designed. The advantages of resistive sensors are easy fabrication, simple operation, and low production cost. Composite polymer films exhibit good sensitivity to low gas concentrations at room temperatures. The principle of the designed sensor array is a change of electrical resistance in dependence of gas concentration. Polyaniline (PANI), PANI/carbon nanotubes, PANI/SnO 2 , and PANI/TiO 2 composites were used as active layers. Gas sensing properties of active layers for NH 3 , CO 2 , NO 2 , O 2 , acetone, toluene, and relative humidity were studied. PANI composites, unlike pristine PANI, exhibit good reversibility and lower temperature dependence.
- 2 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 18 (9) , 3759-3766
Performance Evaluation of Low-Cost Flexible Gas Sensor Array With Nanocomposite Polyaniline Films
The aim of this paper is to present the design of a sensor array based on a single substrate with various composite polymer films as active layers for gas detection. A low power, four element flexible sensor platform with heater and temperature sensor was designed. The advantages of resistive sensors are easy fabrication, simple operation, and low production cost. Composite polymer films exhibit good sensitivity to low gas concentrations at room temperatures. The principle of the designed sensor array is a change of electrical resistance in dependence of gas concentration. Polyaniline (PANI), PANI/carbon nanotubes, PANI/SnO 2 , and PANI/TiO 2 composites were used as active layers. Gas sensing properties of active layers for NH 3 , CO 2 , NO 2 , O 2 , acetone, toluene, and relative humidity were studied. PANI composites, unlike pristine PANI, exhibit good reversibility and lower temperature dependence.
- Open Access
- 1 March 2018
- Published by Walter de Gruyter GmbH in Journal of Electrical Engineering
- Vol. 69 (2) , 177-182
Screen printed and laminated electrodes for low-cost capacitive level measurement systems
The fabrication procedure and characterization of low-cost electrodes for capacitive level sensors realized on a flexible substrate are presented in this paper. The aim was to prepare conductive electrodes by printing of silver and PEDOT:PSS pastes on coated PET foil. Individual interdigital capacitors and a system with embedded microcontroller readout were designed for a comparative study. Individual capacitors in the form of interdigital electrodes (IDT) were designed with different finger width/spacing dimensions from 300/300 μm to 800/800 μm, a finger length 10 mm and 15 mm and an overall length of 100 mm. A demonstrator device featuring an integrated microcontroller, sensing and reference capacitive sensors and a resistive temperature sensor was realized to proof a practical utilization. The microcontroller is used to calculate capacitances of IDT electrodes in terms of charging time proportional to the fluid level. The design with reference capacitor can be directly applied to different fluids with a wide range of conductivities and dielectric constants without recalibration. The printed structures were thermally laminated with covering PET foil. The sensitivity of the fabricated devices was characterized in liquids with different relative permittivity and conductivity (water and oil). The highest measured sensitivity was 0.7 pF/mm and 0.08 pF/mm for water and oil respectively, with resolution down to 0.1 mm.
- 1 March 2018
- Published by Walter de Gruyter GmbH in Journal of Electrical Engineering
- Vol. 69 (2) , 177-182
Open AccessScreen printed and laminated electrodes for low-cost capacitive level measurement systems
The fabrication procedure and characterization of low-cost electrodes for capacitive level sensors realized on a flexible substrate are presented in this paper. The aim was to prepare conductive electrodes by printing of silver and PEDOT:PSS pastes on coated PET foil. Individual interdigital capacitors and a system with embedded microcontroller readout were designed for a comparative study. Individual capacitors in the form of interdigital electrodes (IDT) were designed with different finger width/spacing dimensions from 300/300 μm to 800/800 μm, a finger length 10 mm and 15 mm and an overall length of 100 mm. A demonstrator device featuring an integrated microcontroller, sensing and reference capacitive sensors and a resistive temperature sensor was realized to proof a practical utilization. The microcontroller is used to calculate capacitances of IDT electrodes in terms of charging time proportional to the fluid level. The design with reference capacitor can be directly applied to different fluids with a wide range of conductivities and dielectric constants without recalibration. The printed structures were thermally laminated with covering PET foil. The sensitivity of the fabricated devices was characterized in liquids with different relative permittivity and conductivity (water and oil). The highest measured sensitivity was 0.7 pF/mm and 0.08 pF/mm for water and oil respectively, with resolution down to 0.1 mm.
- Open Access
- 3 January 2018
- Published by Beilstein Institut in Beilstein Journal of Nanotechnology
- Vol. 9 (1) , 22-29
Gas-sensing behaviour of ZnO/diamond nanostructures
Microstructured single- and double-layered sensor devices based on p-type hydrogen-terminated nanocrystalline diamond (NCD) films and/or n-type ZnO nanorods (NRs) have been obtained via a facile microwave-plasma-enhanced chemical vapour deposition process or a hydrothermal growth procedure. The morphology and crystal structure of the synthesized materials was analysed with scanning electron microscopy, X-ray diffraction measurements and Raman spectroscopy. The gas sensing properties of the sensors based on i) NCD films, ii) ZnO nanorods, and iii) hybrid ZnO NRs/NCD structures were evaluated with respect to oxidizing (i.e., NO2, CO2) and reducing (i.e., NH3) gases at 150 °C. The hybrid ZnO NRs/NCD sensor showed a remarkably enhanced NO2 response compared to the ZnO NRs sensor. Further, inspired by this special hybrid structure, the simulation of interaction between the gas molecules (NO2 and CO2) and hybrid ZnO NRs/NCD sensor was studied using DFT calculations.
- 3 January 2018
- Published by Beilstein Institut in Beilstein Journal of Nanotechnology
- Vol. 9 (1) , 22-29
Open AccessGas-sensing behaviour of ZnO/diamond nanostructures
Microstructured single- and double-layered sensor devices based on p-type hydrogen-terminated nanocrystalline diamond (NCD) films and/or n-type ZnO nanorods (NRs) have been obtained via a facile microwave-plasma-enhanced chemical vapour deposition process or a hydrothermal growth procedure. The morphology and crystal structure of the synthesized materials was analysed with scanning electron microscopy, X-ray diffraction measurements and Raman spectroscopy. The gas sensing properties of the sensors based on i) NCD films, ii) ZnO nanorods, and iii) hybrid ZnO NRs/NCD structures were evaluated with respect to oxidizing (i.e., NO2, CO2) and reducing (i.e., NH3) gases at 150 °C. The hybrid ZnO NRs/NCD sensor showed a remarkably enhanced NO2 response compared to the ZnO NRs sensor. Further, inspired by this special hybrid structure, the simulation of interaction between the gas molecules (NO2 and CO2) and hybrid ZnO NRs/NCD sensor was studied using DFT calculations.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 117-120
Acoustic method for respiratory monitoring
This paper describes a method of the respiration monitoring based on the sensing of acoustic signals in trachea. Further, the article describes method for signal processing of the acoustic signals. The respiration belongs among basic vital functions and the knowledge of their parameters and quality is necessary in medicine. The research is leading to the methods, which are inconvenienced patients. Monitoring of respiration is important for monitoring respiration towards observation quality sleeping or The Sudden Infant Death Syndrome (SIDS).
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 117-120
Acoustic method for respiratory monitoring
This paper describes a method of the respiration monitoring based on the sensing of acoustic signals in trachea. Further, the article describes method for signal processing of the acoustic signals. The respiration belongs among basic vital functions and the knowledge of their parameters and quality is necessary in medicine. The research is leading to the methods, which are inconvenienced patients. Monitoring of respiration is important for monitoring respiration towards observation quality sleeping or The Sudden Infant Death Syndrome (SIDS).