Ishtiaq Hassan Wani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ishtiaq Hassan Wani has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Klaus Leifer
Ångström Laboratory, Department of Materials Science and Engineering, Uppsala University, 75121 Uppsala, Sweden
6 shared publications - Hu Li
Shandong University
4 shared publications Aqib Hayat
Applied Materials Science
3 shared publications- Syed Hassan Mujtaba Jafri
Department of Electrical Engineering, Mirpur University of Science and Technology (MUST), Mirpur 10250, Pakistan
3 shared publications Yuanyuan Han
Angstrom Laboratory, Uppsala University, Sweden
3 shared publications- Andreas Orthaber
Synthetic Molecular Chemistry, Department of Chemistry Ångström Laboratory, Uppsala University, BOX 523, 75120 Uppsala, Sweden
2 shared publications
Latest Publications
- Open Access
- 18 March 2019
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 11 (14) , 6571-6575
A sub 20 nm metal-conjugated molecule junction acting as a nitrogen dioxide sensor
A 20 nm gas sensor based on short chain organic molecules detects 55 ppb concentration of NO2.
- 18 March 2019
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 11 (14) , 6571-6575
Open AccessA sub 20 nm metal-conjugated molecule junction acting as a nitrogen dioxide sensor
A 20 nm gas sensor based on short chain organic molecules detects 55 ppb concentration of NO2.
- Open Access
- 23 November 2017
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 922 (1) , 012023
Enhanced gas sensing performance of graphene/ZnS-CdS hetero-nanowires gas sensor synthesized by Langmuir-Blodgett self-assembly method
Graphene is a promising material in the field of solid-state gas sensors due to the unique two-dimensional structure. Here, we have shown by fabricating graphene/ZnS-CdS heteronanowire structure, the gas sensor sensitivity has a two-fold increase to 20% under 15 ppm gaseous concentration compared to a 10% response in pristine graphene. Spectroscopy and microscopy analysis indicate that the semi-conducting ZnS-CdS hetero-nanowires are 2 nm wide and densely packed on top of graphene. By combining UV illumination, the device approaches a fast response/recovery and high gas sensitivity, thus has a potential to be used in a detection of wide range of gases.
- 23 November 2017
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 922 (1) , 012023
Open AccessEnhanced gas sensing performance of graphene/ZnS-CdS hetero-nanowires gas sensor synthesized by Langmuir-Blodgett self-assembly method
Graphene is a promising material in the field of solid-state gas sensors due to the unique two-dimensional structure. Here, we have shown by fabricating graphene/ZnS-CdS heteronanowire structure, the gas sensor sensitivity has a two-fold increase to 20% under 15 ppm gaseous concentration compared to a 10% response in pristine graphene. Spectroscopy and microscopy analysis indicate that the semi-conducting ZnS-CdS hetero-nanowires are 2 nm wide and densely packed on top of graphene. By combining UV illumination, the device approaches a fast response/recovery and high gas sensitivity, thus has a potential to be used in a detection of wide range of gases.
- 1 September 2017
- Published by Elsevier in Powder Technology
- Vol. 319, 163-171
A general strategy for template-free and low-cost synthesis of inorganic hollow spheres
- 1 September 2017
- Published by Elsevier in Powder Technology
- Vol. 319, 163-171
A general strategy for template-free and low-cost synthesis of inorganic hollow spheres
- 22 May 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Medicine
- Vol. 28 (7) , 99
Template-free synthesis of phosphate-based spheres via modified supersaturated phosphate buffer solutions
Modified supersaturated phosphate buffer solutions were used to synthesize phosphate-based spheres, including calcium phosphate (CaP), strontium phosphate (SrP) and barium phosphate (BaP). A series of ions concentrations in the modified phosphate buffer solutions were investigated in order to study their effects in precipitates morphologies. During synthesis, it was found that magnesium was the key factor in sphere formation. The morphologies of calcium phosphate, strontium phosphate and barium phosphate precipitates varied as the concentration of magnesium ions varied. When sufficient magnesium was provided, the precipitates appeared spherical, and the diameter was in range of 0.5–2 μm. The morphologies, compositions and structure of spheres were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and N2 adsorption analysis. Moreover, the application of magnesium substituted calcium phosphate spheres in dentin tubules occlusion was investigated.
- 22 May 2017
- Published by Springer Nature in Journal of Materials Science: Materials in Medicine
- Vol. 28 (7) , 99
Template-free synthesis of phosphate-based spheres via modified supersaturated phosphate buffer solutions
Modified supersaturated phosphate buffer solutions were used to synthesize phosphate-based spheres, including calcium phosphate (CaP), strontium phosphate (SrP) and barium phosphate (BaP). A series of ions concentrations in the modified phosphate buffer solutions were investigated in order to study their effects in precipitates morphologies. During synthesis, it was found that magnesium was the key factor in sphere formation. The morphologies of calcium phosphate, strontium phosphate and barium phosphate precipitates varied as the concentration of magnesium ions varied. When sufficient magnesium was provided, the precipitates appeared spherical, and the diameter was in range of 0.5–2 μm. The morphologies, compositions and structure of spheres were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and N2 adsorption analysis. Moreover, the application of magnesium substituted calcium phosphate spheres in dentin tubules occlusion was investigated.
- 2 February 2017
- Published by Royal Society of Chemistry (RSC) in Molecular Systems Design & Engineering
- Vol. 2 (2) , 133-139
Designing sterically demanding thiolate coated AuNPs for electrical characterization of BPDT in a NP–molecule–nanoelectrode platform
Molecular electronics with single or few molecules requires a stable metal–molecule nanojunction platform. Herein, we report the design and synthesis of gold nanoparticles coated with sterically demanding thiol ligands that are essential to fabricate a versatile and stable nanoelectrode–molecule–nanoparticle platform suitable for electrical characterization of small organic molecules. By combining ω-tetraphenylmethane ether functionalized alkyl thioacetate and alkyl thiols, we prepared highly stable gold nanoparticles in a one-phase reaction providing simple and efficient purification. This robust preparation gives highly pure nanoparticles in very high yields (up to 90%) with long-time shelf stability. The synthesis in this work has superior reproducibility compared to previous synthesis processes that are currently being used for such molecular electronics platforms. Electron microscopy confirms the formation of uniform and small nanoparticles in the range of 5 to 7 nm. These nanoparticles with different ligand surface coverages were placed in a 20 nm nanoelectrode setup using dielectrophoretic forces. This setup was utilized to characterize the conductivity of the molecular wire 4,4′-biphenyldithiol introduced via ligand place-exchange under ambient conditions.
- 2 February 2017
- Published by Royal Society of Chemistry (RSC) in Molecular Systems Design & Engineering
- Vol. 2 (2) , 133-139
Designing sterically demanding thiolate coated AuNPs for electrical characterization of BPDT in a NP–molecule–nanoelectrode platform
Molecular electronics with single or few molecules requires a stable metal–molecule nanojunction platform. Herein, we report the design and synthesis of gold nanoparticles coated with sterically demanding thiol ligands that are essential to fabricate a versatile and stable nanoelectrode–molecule–nanoparticle platform suitable for electrical characterization of small organic molecules. By combining ω-tetraphenylmethane ether functionalized alkyl thioacetate and alkyl thiols, we prepared highly stable gold nanoparticles in a one-phase reaction providing simple and efficient purification. This robust preparation gives highly pure nanoparticles in very high yields (up to 90%) with long-time shelf stability. The synthesis in this work has superior reproducibility compared to previous synthesis processes that are currently being used for such molecular electronics platforms. Electron microscopy confirms the formation of uniform and small nanoparticles in the range of 5 to 7 nm. These nanoparticles with different ligand surface coverages were placed in a 20 nm nanoelectrode setup using dielectrophoretic forces. This setup was utilized to characterize the conductivity of the molecular wire 4,4′-biphenyldithiol introduced via ligand place-exchange under ambient conditions.
- Open Access
- 20 December 2016
- Published by Wiley
- p. 435-436
Focused ion beam based highly resistive and reproducible sub‐5nm nanogaps in thin gold wire
- 20 December 2016
- Published by Wiley
- p. 435-436
Open AccessFocused ion beam based highly resistive and reproducible sub‐5nm nanogaps in thin gold wire
- 7 September 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (10) , 103108
Fabrication of reproducible sub-5 nm nanogaps by a focused ion beam and observation of Fowler-Nordheim tunneling
Creating a stable high resistance sub-5 nm nanogap in between conductive electrodes is one of the major challenges in the device fabrication of nano-objects. Gap-sizes of 20 nm and above can be fabricated reproducibly by the precise focusing of the ion beam and careful milling of the metallic lines. Here, by tuning ion dosages starting from 4.6 × 1010 ions/cm and above, reproducible nanogaps with sub-5 nm sizes are milled with focused ion beam. The resistance as a function of gap dimension shows an exponential behavior, and Fowler-Nordheim tunneling effect was observed in nanoelectrodes with sub-5 nm nanogaps. The application of Simmon's model to the milled nanogaps and the electrical analysis indicates that the minimum nanogap size approaches to 2.3 nm.
- 7 September 2015
- Published by AIP Publishing in Applied Physics Letters
- Vol. 107 (10) , 103108
Fabrication of reproducible sub-5 nm nanogaps by a focused ion beam and observation of Fowler-Nordheim tunneling
Creating a stable high resistance sub-5 nm nanogap in between conductive electrodes is one of the major challenges in the device fabrication of nano-objects. Gap-sizes of 20 nm and above can be fabricated reproducibly by the precise focusing of the ion beam and careful milling of the metallic lines. Here, by tuning ion dosages starting from 4.6 × 1010 ions/cm and above, reproducible nanogaps with sub-5 nm sizes are milled with focused ion beam. The resistance as a function of gap dimension shows an exponential behavior, and Fowler-Nordheim tunneling effect was observed in nanoelectrodes with sub-5 nm nanogaps. The application of Simmon's model to the milled nanogaps and the electrical analysis indicates that the minimum nanogap size approaches to 2.3 nm.