Jesper Lansink Rotgerink
Jesper Lansink Rotgerink has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Frank Leferink
University of Twente
3 shared publications - Harmen Schippers
Royal Netherlands Aerospace Centre
2 shared publications - Alberto Gascón Bravo
University of Granada
1 shared publication - Alejandro Muñoz Manterola
University of Granada
1 shared publication - Luis Diaz Angulo
University of Granada
1 shared publication - Niek Moonen
Faculty of Electrical Engineering, Mathematics and Computer Science, University of Twente, Enschede, The Netherlands
1 shared publication
Latest Publications
- Open Access
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 68 (5) , 1226-1233
Numerical Computation of Unshielded Multiwires In-Cell Parameters for Coupling Between FDTD and MTL Methods Using Multipolar Expansions
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 68 (5) , 1226-1233
Open AccessNumerical Computation of Unshielded Multiwires In-Cell Parameters for Coupling Between FDTD and MTL Methods Using Multipolar Expansions
- Open Access
- 19 August 2021
- Published by University Library/University of Twente
Crosstalk Analysis in Aerospace Environments
- 19 August 2021
- Published by University Library/University of Twente
Open AccessCrosstalk Analysis in Aerospace Environments
- 10 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 63 (4) , 1231-1239
Multiconductor Transmission Line Modeling of Crosstalk Between Cables in the Presence of Composite Ground Planes
Modern transportation systems, such as aircraft, are increasingly replacing metal body parts for composite materials, such as carbon-fiber reinforced plastics. Despite the multiple advantages in terms of weight, size, and fuel consumption, this trend is posing a challenge for protection of cables against electromagnetic interference. Early risk assessment and optimization of cable design in modern aircraft require reliable methods that can quickly and accurately estimate crosstalk behavior in the presence of lossy ground planes. This article presents two novel methods to incorporate such lossy ground planes into the crosstalk modeling of cable bundles. The first method considers the ground plane as a discrete collection of cylindrical conductors. In the second method a ground impedance matrix is derived for lossy ground planes with a finite thickness. Results of both methods are compared to full-wave simulations and measurements, yielding excellent results in terms of accuracy and computation times. The discretized ground plane method is also applied to the case of wire pairs that are enclosed by two ground planes, both aluminum and carbon–fiber reinforced plastic, as a first step towards investigation of wiring that is embedded in thermoplastic material. Once more simulations and measurements are in good agreement.
- 10 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 63 (4) , 1231-1239
Multiconductor Transmission Line Modeling of Crosstalk Between Cables in the Presence of Composite Ground Planes
Modern transportation systems, such as aircraft, are increasingly replacing metal body parts for composite materials, such as carbon-fiber reinforced plastics. Despite the multiple advantages in terms of weight, size, and fuel consumption, this trend is posing a challenge for protection of cables against electromagnetic interference. Early risk assessment and optimization of cable design in modern aircraft require reliable methods that can quickly and accurately estimate crosstalk behavior in the presence of lossy ground planes. This article presents two novel methods to incorporate such lossy ground planes into the crosstalk modeling of cable bundles. The first method considers the ground plane as a discrete collection of cylindrical conductors. In the second method a ground impedance matrix is derived for lossy ground planes with a finite thickness. Results of both methods are compared to full-wave simulations and measurements, yielding excellent results in terms of accuracy and computation times. The discretized ground plane method is also applied to the case of wire pairs that are enclosed by two ground planes, both aluminum and carbon–fiber reinforced plastic, as a first step towards investigation of wiring that is embedded in thermoplastic material. Once more simulations and measurements are in good agreement.
- 18 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 61 (5) , 1612-1620
Low-Frequency Analysis of Multiconductor Transmission Lines for Crosstalk Design Rules
For early risk assessment in the design of cabling in an aircraft, as well as cable bundle optimization, efficient crosstalk estimations, and dependency of crosstalk with respect to designable parameters are required. A low-frequency technique for analyzing crosstalk in multiconductor transmission lines is presented. The result of this analysis is a closed-form expression for crosstalk in a specific cabling configuration. The technique has been validated via measurements and is used in two examples comprising two wire pairs close to a ground plane and in free space. Low-frequency closed-form expressions for near-end crosstalk are derived for both situations, which directly relate any designable parameter to crosstalk levels. Moreover, these expressions clearly show differences between the cases with and without a ground plane. Specifically, with the ground plane, the decrease in crosstalk when doubling the separation distance is 24 dB for pairs close to the ground, while it is 12 dB in free space. The closed-form expressions are utilized to create an overview of sensitivities of crosstalk to all designable parameters for both configurations. Finally, the low-frequency approximations of the chain parameters are applied to more complex nonuniform transmission lines, yielding more than 20 times faster computations when compared with complete MTL simulations.
- 18 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 61 (5) , 1612-1620
Low-Frequency Analysis of Multiconductor Transmission Lines for Crosstalk Design Rules
For early risk assessment in the design of cabling in an aircraft, as well as cable bundle optimization, efficient crosstalk estimations, and dependency of crosstalk with respect to designable parameters are required. A low-frequency technique for analyzing crosstalk in multiconductor transmission lines is presented. The result of this analysis is a closed-form expression for crosstalk in a specific cabling configuration. The technique has been validated via measurements and is used in two examples comprising two wire pairs close to a ground plane and in free space. Low-frequency closed-form expressions for near-end crosstalk are derived for both situations, which directly relate any designable parameter to crosstalk levels. Moreover, these expressions clearly show differences between the cases with and without a ground plane. Specifically, with the ground plane, the decrease in crosstalk when doubling the separation distance is 24 dB for pairs close to the ground, while it is 12 dB in free space. The closed-form expressions are utilized to create an overview of sensitivities of crosstalk to all designable parameters for both configurations. Finally, the low-frequency approximations of the chain parameters are applied to more complex nonuniform transmission lines, yielding more than 20 times faster computations when compared with complete MTL simulations.
- Open Access
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1103-1108
Automated equivalent circuit extraction of impedance curves using a Gauss-Newton algorithm
In this study, an algorithm has been implemented to automate the extraction of passive component values from impedance curves. The method has been applied to a Common Mode (CM) filter. The novelty of this paper lies in the possibility to fit any equivalent circuit to any impedance curve with a relative efficient algorithm. This allows for back-annotation of fields into equivalent circuit simulators.
- 1 May 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1103-1108
Open AccessAutomated equivalent circuit extraction of impedance curves using a Gauss-Newton algorithm
In this study, an algorithm has been implemented to automate the extraction of passive component values from impedance curves. The method has been applied to a Common Mode (CM) filter. The novelty of this paper lies in the possibility to fit any equivalent circuit to any impedance curve with a relative efficient algorithm. This allows for back-annotation of fields into equivalent circuit simulators.