R. P. Vijayakumar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
R. P. Vijayakumar has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
Ashutosh Kr Chaudhary
Department of Chemical Engineering, Visvesvaraya National Institute of Technology, Nagpur, India
11 shared publicationsShubham P. Chitriv
Department of Chemical Engineering, Visvesvaraya National Institute of Technology, Nagpur, 440010, India
4 shared publications- Ganesh Bajad
Department of Chemical Engineering, Visvesvaraya National Institute of Technology, Nagpur, India
3 shared publications Kundrapu Chaitanya
Department of Chemical Engineering, Visvesvaraya National Institute of Technology, Nagpur, India
3 shared publicationsM. Ismail Shahib
3 shared publications- Parul Dwivedi
Department of Chemical Engineering, Harcourt Butler Technical University, Kanpur, India
3 shared publications
Latest Publications
- 22 September 2026
- Published by Wiley in Polymer Engineering & Science
Reprocessable Elastomeric Networks Produced via Trimesic Acid‐Induced β‐Hydroxy Ester Crosslinking of Epoxidized Natural Rubber With Tunable Mechanical Properties
Trimesic acid (TMA) has been employed as a trifunctional crosslinker to develop dynamic epoxidized natural rubber (ENR) networks through zinc‐acetate‐catalyzed formation of β‐hydroxy ester linkages. Unlike conventional sulfur‐vulcanized networks, which are commonly described using simplified tetrafunctional junction models and often neglect the finite length of sulfur bridges between crosslinking points, TMA introduces a distinct trifunctional network architecture. Systematic variation of TMA content reveals a strong influence on network structure and molecular dynamics, with a small change in crosslinker concentration producing a remarkable shift in T g of approximately 33°C, accompanied by significant changes in mechanical properties. The dynamic ester‐based network further enables efficient reprocessing with high retention of mechanical performance. These results demonstrate that crosslinker functionality and molecular architecture, rather than crosslink density alone, can critically govern the structure–property relationship of rubber networks, providing new experimental insight for developing theoretical descriptions of trifunctional elastomer networks.
- 22 September 2026
- Published by Wiley in Polymer Engineering & Science
Reprocessable Elastomeric Networks Produced via Trimesic Acid‐Induced β‐Hydroxy Ester Crosslinking of Epoxidized Natural Rubber With Tunable Mechanical Properties
Trimesic acid (TMA) has been employed as a trifunctional crosslinker to develop dynamic epoxidized natural rubber (ENR) networks through zinc‐acetate‐catalyzed formation of β‐hydroxy ester linkages. Unlike conventional sulfur‐vulcanized networks, which are commonly described using simplified tetrafunctional junction models and often neglect the finite length of sulfur bridges between crosslinking points, TMA introduces a distinct trifunctional network architecture. Systematic variation of TMA content reveals a strong influence on network structure and molecular dynamics, with a small change in crosslinker concentration producing a remarkable shift in T g of approximately 33°C, accompanied by significant changes in mechanical properties. The dynamic ester‐based network further enables efficient reprocessing with high retention of mechanical performance. These results demonstrate that crosslinker functionality and molecular architecture, rather than crosslink density alone, can critically govern the structure–property relationship of rubber networks, providing new experimental insight for developing theoretical descriptions of trifunctional elastomer networks.
- Open Access
- 26 May 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Resource Management
- Vol. 3 (7) , 2081-2096
Technical and Life Cycle Assessment of Carbon Nanomaterial Production From Waste Toner Using Valorized Toner Ash and Magnetite Tailing Supports
- 26 May 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Resource Management
- Vol. 3 (7) , 2081-2096
Open AccessTechnical and Life Cycle Assessment of Carbon Nanomaterial Production From Waste Toner Using Valorized Toner Ash and Magnetite Tailing Supports
- 17 December 2025
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 17 (10) , 5413-5428
Waste to Wealth: Upcycling Waste Toner Powder to Magnetic Multiwalled Carbon Nanotube Composites for Energy Storage Applications
- 17 December 2025
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 17 (10) , 5413-5428
Waste to Wealth: Upcycling Waste Toner Powder to Magnetic Multiwalled Carbon Nanotube Composites for Energy Storage Applications
- 31 May 2025
- Published by Elsevier in Waste Management
- Vol. 204, 114911
A review on end-of-life waste toner powder: recovery, utilization and upcycling
- 31 May 2025
- Published by Elsevier in Waste Management
- Vol. 204, 114911
A review on end-of-life waste toner powder: recovery, utilization and upcycling
- 21 May 2025
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 27 (4) , 2454-2466
Hydrothermal conversion of end-of-life waste toner powder into magnetic carbon-iron nanocomposite for energy storage applications
- 21 May 2025
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 27 (4) , 2454-2466
Hydrothermal conversion of end-of-life waste toner powder into magnetic carbon-iron nanocomposite for energy storage applications
- 18 November 2024
- Published by Springer Nature in Cellulose
- Vol. 32 (1) , 569-585
A sustainable approach for the simultaneous removal of cationic and anionic dyes from waste water using multilayer MWCNT, UMCNO, and PVA coated cotton fabrics
- 18 November 2024
- Published by Springer Nature in Cellulose
- Vol. 32 (1) , 569-585
A sustainable approach for the simultaneous removal of cationic and anionic dyes from waste water using multilayer MWCNT, UMCNO, and PVA coated cotton fabrics
- 9 August 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (41)
Synthesis of PVA–MWCNTs–UMCNOs–starch crosslinked nanocomposite biodegradable films for the removal of methylene blue and Congo red dyes from wastewater
Plastic waste and wastewater are indeed significant environmental issues that have wide‐ranging impacts on ecosystems, human health, and the economy. This study outlines the synthesis of biodegradable polyvinyl alcohol (PVA)–starch polymeric films incorporating multiwalled carbon nanotubes (MWCNTs) derived from plastic waste and unzipped carbon nanotubes oxides (UMCNOs) as co‐filled nanomaterials. These films were formulated based on data generated using a mixture design method in Design Expert 13 software, resulting in the synthesis of 19 films utilizing five types of PVA–starch polymer solutions (Types A–E). The synthesized films underwent characterization to study their surface morphology via scanning electron microscope and Fourier transform infrared spectroscopy analysis. Subsequently, the films were individually subjected to vacuum filtration, through which cationic dyes such as methylene blue (MB) and anionic dye Congo red (CR) were passed in batches. The highest removal efficiency of 96.43% for MB dye was achieved, accompanied by an exceptionally high flux of 3146.78 LMH. Similarly, the maximum removal of 88.08% for CR was observed with a flux of 1512.66 LMH. The renewable active sites mechanism resulted in increased dye removal with every cycle. Results indicated efficient reusability, particularly when washed with ethanol–water solution.
- 9 August 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (41)
Synthesis of PVA–MWCNTs–UMCNOs–starch crosslinked nanocomposite biodegradable films for the removal of methylene blue and Congo red dyes from wastewater
Plastic waste and wastewater are indeed significant environmental issues that have wide‐ranging impacts on ecosystems, human health, and the economy. This study outlines the synthesis of biodegradable polyvinyl alcohol (PVA)–starch polymeric films incorporating multiwalled carbon nanotubes (MWCNTs) derived from plastic waste and unzipped carbon nanotubes oxides (UMCNOs) as co‐filled nanomaterials. These films were formulated based on data generated using a mixture design method in Design Expert 13 software, resulting in the synthesis of 19 films utilizing five types of PVA–starch polymer solutions (Types A–E). The synthesized films underwent characterization to study their surface morphology via scanning electron microscope and Fourier transform infrared spectroscopy analysis. Subsequently, the films were individually subjected to vacuum filtration, through which cationic dyes such as methylene blue (MB) and anionic dye Congo red (CR) were passed in batches. The highest removal efficiency of 96.43% for MB dye was achieved, accompanied by an exceptionally high flux of 3146.78 LMH. Similarly, the maximum removal of 88.08% for CR was observed with a flux of 1512.66 LMH. The renewable active sites mechanism resulted in increased dye removal with every cycle. Results indicated efficient reusability, particularly when washed with ethanol–water solution.
- 22 May 2024
- Published by Wiley in Chemical Engineering & Technology
- Vol. 47 (7) , 1031-1043
Influence of Unzipped Multiwalled Carbon Nanotube Oxides‐Epoxy Paint on the Corrosion Rate of Mild Steel in Marine Environment
In recent years, numerous innovative approaches have emerged to enhance the corrosion resistance of materials. This study investigates the effect of enhancing mild steel corrosion through the incorporation of unzipped multiwalled carbon nanotube oxides (UMCNO) into epoxy resin. Additionally, the effect of various operating parameters, such as temperature, UMCNO concentration, salt concentration, duration of exposure, and coating thickness, have also been considered in the study. The Box–Behnken method was used for experimental design and correlation of corrosion rate with various operating parameters, followed by analysis of variance of both five‐ and three‐parameter models. Notably, despite variations in temperature and salt concentration, the corrosion rate remained negligible, confirming its suitability in various marine conditions. Furthermore, it was observed that the corrosion rate of mild steel coated with epoxy decreased with the addition of UMCNO. A corrosion rate of 0.182 mpy was observed for epoxy resin incorporated with 0.5 % UMCNO over a 14‐day period, which is lower compared to other conditions. Electrochemical impedance spectroscopy and potentiodynamic polarization analysis showed higher corrosion‐resistant properties in epoxy coating incorporated with UMCNO. In addition, it was evident from the contact angle measurement that the corrosion rate of mild steel was highly dependent on the concentration of UMCNO.
- 22 May 2024
- Published by Wiley in Chemical Engineering & Technology
- Vol. 47 (7) , 1031-1043
Influence of Unzipped Multiwalled Carbon Nanotube Oxides‐Epoxy Paint on the Corrosion Rate of Mild Steel in Marine Environment
In recent years, numerous innovative approaches have emerged to enhance the corrosion resistance of materials. This study investigates the effect of enhancing mild steel corrosion through the incorporation of unzipped multiwalled carbon nanotube oxides (UMCNO) into epoxy resin. Additionally, the effect of various operating parameters, such as temperature, UMCNO concentration, salt concentration, duration of exposure, and coating thickness, have also been considered in the study. The Box–Behnken method was used for experimental design and correlation of corrosion rate with various operating parameters, followed by analysis of variance of both five‐ and three‐parameter models. Notably, despite variations in temperature and salt concentration, the corrosion rate remained negligible, confirming its suitability in various marine conditions. Furthermore, it was observed that the corrosion rate of mild steel coated with epoxy decreased with the addition of UMCNO. A corrosion rate of 0.182 mpy was observed for epoxy resin incorporated with 0.5 % UMCNO over a 14‐day period, which is lower compared to other conditions. Electrochemical impedance spectroscopy and potentiodynamic polarization analysis showed higher corrosion‐resistant properties in epoxy coating incorporated with UMCNO. In addition, it was evident from the contact angle measurement that the corrosion rate of mild steel was highly dependent on the concentration of UMCNO.
- 15 November 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 220
Unzipped multiwalled carbon nanotube oxide / PEG based phase change composite for latent heat energy storage
- 15 November 2023
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 220
Unzipped multiwalled carbon nanotube oxide / PEG based phase change composite for latent heat energy storage