Esther Rilo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Esther Rilo has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Oscar Cabeza
MESTURAS Group, Departamento de Física y Ciencias de la Tierra, Universidade da Coruña, 15071 A Coruña, Spain
24 shared publications - Luis Miguel Varela
Grupo de Nanomateriais, Fotónica e Materia Branda, Departamento de Física de Partículas, Universidade de Santiago de Compostela, Campus Vida s/n, Santiago de Compostela E-15782, Spain
15 shared publications - Luisa Segade
Departamento de Física, Facultade de Ciencias, Universidade da Coruña, 15071 A Coruña, Spain
10 shared publications - Montserrat Domínguez-Pérez
Departamento de Física, Facultade de Ciencias, Universidade da Coruña, 15071 A Coruña, Spain
10 shared publications J. Vila
7 shared publications- Elena López Lago
Departamento de Física Aplicada, Facultade de Óptica e Optometríae Instituto de Materiais (iMATUS) Campus Vida, Universidade de Santiago de Compostela (USC), 15782 Galicia, Spain
4 shared publications
Latest Publications
- 3 March 2018
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 20 (13) , 8724-8736
Mesostructure and physical properties of aqueous mixtures of the ionic liquid 1-ethyl-3-methyl imidazolium octyl sulfate doped with divalent sulfate salts in the liquid and the mesomorphic states
This paper extends the study of the induced temperature change in the mesostructure and in the physical properties occurring in aqueous mixtures of the ionic liquid 1-ethyl-3-methyl imidazolium octyl-sulfate [EMIm][OSO4]. For some compositions, these mixtures undergo a phase transition between the liquid (isotropic in the mesoscale) and the mesomorphic state (lyotropic liquid crystalline) at about room temperature. The behavior of mixtures doped with a divalent metal sulfate was investigated in order to observe their applicability as electrolytes. Calcium sulfate salt is almost insoluble even in the 20 wt% water mixture. The magnesium salt, in contrast, can be dissolved up to concentrations of 730 ppm in the same mixture and it has a profound impact on its properties. Six aqueous mixtures (with water content from 10 wt% to 33 wt%) of [EMIm][OSO4] were saturated with magnesium sulfate salt, producing the ternary mixture [EMIm][OSO4] + H2O + MgSO4. Viscosity, density and ionic conductivity for these samples were measured from 10 °C to 90 °C. In addition, SAXS, FTIR, diffussion NMR and Raman spectroscopy of the most interesting samples have been performed, and structural data indicate a transition between a hexagonal lyotropic liquid crystalline phase below and an isotropic solution phase above room temperature. The octyl sulfate anions of the cylindrical micelles in the hexagonal phase are coordinated with water molecules through H-bonds (about four per sulfate anion), while the [EMIm] cations seem to be poorly coordinated and so free to move. Inorganic salt addition reinforces that network, increasing the phase transition temperature.
- 3 March 2018
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 20 (13) , 8724-8736
Mesostructure and physical properties of aqueous mixtures of the ionic liquid 1-ethyl-3-methyl imidazolium octyl sulfate doped with divalent sulfate salts in the liquid and the mesomorphic states
This paper extends the study of the induced temperature change in the mesostructure and in the physical properties occurring in aqueous mixtures of the ionic liquid 1-ethyl-3-methyl imidazolium octyl-sulfate [EMIm][OSO4]. For some compositions, these mixtures undergo a phase transition between the liquid (isotropic in the mesoscale) and the mesomorphic state (lyotropic liquid crystalline) at about room temperature. The behavior of mixtures doped with a divalent metal sulfate was investigated in order to observe their applicability as electrolytes. Calcium sulfate salt is almost insoluble even in the 20 wt% water mixture. The magnesium salt, in contrast, can be dissolved up to concentrations of 730 ppm in the same mixture and it has a profound impact on its properties. Six aqueous mixtures (with water content from 10 wt% to 33 wt%) of [EMIm][OSO4] were saturated with magnesium sulfate salt, producing the ternary mixture [EMIm][OSO4] + H2O + MgSO4. Viscosity, density and ionic conductivity for these samples were measured from 10 °C to 90 °C. In addition, SAXS, FTIR, diffussion NMR and Raman spectroscopy of the most interesting samples have been performed, and structural data indicate a transition between a hexagonal lyotropic liquid crystalline phase below and an isotropic solution phase above room temperature. The octyl sulfate anions of the cylindrical micelles in the hexagonal phase are coordinated with water molecules through H-bonds (about four per sulfate anion), while the [EMIm] cations seem to be poorly coordinated and so free to move. Inorganic salt addition reinforces that network, increasing the phase transition temperature.
- 26 December 2017
- Published by Royal Society of Chemistry (RSC) in Materials Chemistry Frontiers
- Vol. 2 (3) , 505-513
Imidazolium decyl sulfate: a very promising selfmade ionic hydrogel
In this paper, we show, for the first time, the synthesis, structural characterization, phase diagram and physical properties of the ionic liquid, 1-ethyl-3-methyl imidazolium decyl sulfate [EMIm][DSO4]. At 25 °C it is either a crystalline solid or a liquid depending on the thermal history as its melting point is about 33 °C and its point of solidification is about 22 °C. The interest of this new IL lies in its ability to become a rigid hydrogel when mixed with water. As observed in many ILs, the as-prepared IL is hygroscopic and it adsorbs about 14 wt% of water at usual laboratory conditions and up to 27 wt% in a 100% saturated atmosphere. Due to the H-bonds between water and the amphiphilic [DSO4] anions, a lyotropic HI liquid crystalline phase is formed in the hydrated state, which can be observed in micrographs recorded using white polarized light. The moisture adsorption is a completely reversible process; thus, the rigid-gel sample loses all adsorbed water when it is left in a dry atmosphere for a few hours, transitioning to the liquid state. Phase diagrams of the temperature-water concentration is presented and compared with that of the parent compound [EMIm] octyl sulfate, [OSO4]. X-ray diffraction revels that below 15 °C the hydrated compound crystallizes into a P2/m monoclinic structure. The structure of the new compound was confirmed by NMR, FTIR and mass spectroscopy (MS). In addition, the temperature behavior of ionic conductivity was experimentally measured and analyzed for the pure compound and for two samples hydrated with 10 wt% and 39 wt% of water. Viscosity and density were also measured vs. temperature for the pure sample. The as-prepared IL shows great potential for numerous practical applications.
- 26 December 2017
- Published by Royal Society of Chemistry (RSC) in Materials Chemistry Frontiers
- Vol. 2 (3) , 505-513
Imidazolium decyl sulfate: a very promising selfmade ionic hydrogel
In this paper, we show, for the first time, the synthesis, structural characterization, phase diagram and physical properties of the ionic liquid, 1-ethyl-3-methyl imidazolium decyl sulfate [EMIm][DSO4]. At 25 °C it is either a crystalline solid or a liquid depending on the thermal history as its melting point is about 33 °C and its point of solidification is about 22 °C. The interest of this new IL lies in its ability to become a rigid hydrogel when mixed with water. As observed in many ILs, the as-prepared IL is hygroscopic and it adsorbs about 14 wt% of water at usual laboratory conditions and up to 27 wt% in a 100% saturated atmosphere. Due to the H-bonds between water and the amphiphilic [DSO4] anions, a lyotropic HI liquid crystalline phase is formed in the hydrated state, which can be observed in micrographs recorded using white polarized light. The moisture adsorption is a completely reversible process; thus, the rigid-gel sample loses all adsorbed water when it is left in a dry atmosphere for a few hours, transitioning to the liquid state. Phase diagrams of the temperature-water concentration is presented and compared with that of the parent compound [EMIm] octyl sulfate, [OSO4]. X-ray diffraction revels that below 15 °C the hydrated compound crystallizes into a P2/m monoclinic structure. The structure of the new compound was confirmed by NMR, FTIR and mass spectroscopy (MS). In addition, the temperature behavior of ionic conductivity was experimentally measured and analyzed for the pure compound and for two samples hydrated with 10 wt% and 39 wt% of water. Viscosity and density were also measured vs. temperature for the pure sample. The as-prepared IL shows great potential for numerous practical applications.
- Open Access
- 31 October 2014
- Published by MDPI AG
Synthesis and Properties of a New Ionic Liquid Which Jellyfies at Room Conditions
In this communication the synthesis and physical properties of the new ionic liquid 1-ethyl-3-methyl imidazolium decyl sulfate, are shown. The interest of this new salt lies in its tendency to jellify when it is exposed to the atmosphere by absorbing water from moisture up to about a 10% of its own mass; then it keeps the mass ±2% stable depending on the atmospheric humidity grade. The rigid-gel state appears from 15 ºC to 60 ºC. Below 15 ºC it crystallizes and above 60 ºC it liquefies. According to TGA measurements the compound is stable up to 300ºC. 1-ethyl-3-methyl imidazolium decyl sulfate was prepared in two steps. First the alkylation of 1-methylimidazole with diethyl sulfate afforded 1-ethyl-3-methylimidazolium ethyl sulfate. Then a later trans-esterification reaction allowed obtaining the desired 1-ethyl-3-methyl imidazolium decyl sulfate with high yield and purity. Its structure was confirmed by 1H, 13C NMR and IR spectroscopy as well as Mass Spectrometry. The FTIR spectrum of this new compound, and the temperature behavior of some physical properties such as electrical conductivity, viscosity, density and refractive index, will be presented.
- 31 October 2014
- Published by MDPI AG
Open AccessSynthesis and Properties of a New Ionic Liquid Which Jellyfies at Room Conditions
In this communication the synthesis and physical properties of the new ionic liquid 1-ethyl-3-methyl imidazolium decyl sulfate, are shown. The interest of this new salt lies in its tendency to jellify when it is exposed to the atmosphere by absorbing water from moisture up to about a 10% of its own mass; then it keeps the mass ±2% stable depending on the atmospheric humidity grade. The rigid-gel state appears from 15 ºC to 60 ºC. Below 15 ºC it crystallizes and above 60 ºC it liquefies. According to TGA measurements the compound is stable up to 300ºC. 1-ethyl-3-methyl imidazolium decyl sulfate was prepared in two steps. First the alkylation of 1-methylimidazole with diethyl sulfate afforded 1-ethyl-3-methylimidazolium ethyl sulfate. Then a later trans-esterification reaction allowed obtaining the desired 1-ethyl-3-methyl imidazolium decyl sulfate with high yield and purity. Its structure was confirmed by 1H, 13C NMR and IR spectroscopy as well as Mass Spectrometry. The FTIR spectrum of this new compound, and the temperature behavior of some physical properties such as electrical conductivity, viscosity, density and refractive index, will be presented.
- 1 August 2014
- Published by Elsevier in The Journal of Chemical Thermodynamics
- Vol. 75, 52-57
Physical properties of aqueous mixtures of the ionic 1-ethl-3-methyl imidazolium octyl sulfate: A new ionic rigid gel
- 1 August 2014
- Published by Elsevier in The Journal of Chemical Thermodynamics
- Vol. 75, 52-57
Physical properties of aqueous mixtures of the ionic 1-ethl-3-methyl imidazolium octyl sulfate: A new ionic rigid gel
- 29 January 2013
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry B
- Vol. 117 (5) , 1411-1418
Electrical Conductivity of Seven Binary Systems Containing 1-Ethyl-3-methyl Imidazolium Alkyl Sulfate Ionic Liquids with Water or Ethanol at Four Temperatures
We present experimental measurements of specific electrical (or ionic) conductivity of seven binary systems of 1-ethyl-3-methyl imidazolium alkyl sulfate (EMIM-CnS) with water or ethanol. Electrical conductivity was measured at 298.15 K in all ranges of concentrations and selected mixtures also at 288.15, 308.15, and 318.15 K. The alkyl chains of the anions used are ethyl (EMIM-ES), butyl (EMIM-BS), hexyl (EMIM-HS), and, only for mixtures with ethanol, octyl (EMIM-OS). Let us note that the four ionic liquids (ILs) measured are miscible in water and ethanol at those temperatures and atmospheric pressure in all ranges of concentrations, but EMIM-OS jellifies for a given range of concentration with water. We compare the measured data in terms of the alkyl chain length and solvent nature. Data are compared with previously scarce results for these same systems and also for other aqueous and ethanol mixtures with ILs. In addition, we verify that our data fit the universal theoretical expression with no fitting parameters given by the pseudolattice-based Bahe–Varela model, except for IL concentrated mixtures. To fit well all ranges of concentrations, we add to the original equation two phenomenological terms with one fitting parameter each. Finally, we calculate the molar conductivity and fit it successfully with an expression derived from Onsager theory.
- 29 January 2013
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry B
- Vol. 117 (5) , 1411-1418
Electrical Conductivity of Seven Binary Systems Containing 1-Ethyl-3-methyl Imidazolium Alkyl Sulfate Ionic Liquids with Water or Ethanol at Four Temperatures
We present experimental measurements of specific electrical (or ionic) conductivity of seven binary systems of 1-ethyl-3-methyl imidazolium alkyl sulfate (EMIM-CnS) with water or ethanol. Electrical conductivity was measured at 298.15 K in all ranges of concentrations and selected mixtures also at 288.15, 308.15, and 318.15 K. The alkyl chains of the anions used are ethyl (EMIM-ES), butyl (EMIM-BS), hexyl (EMIM-HS), and, only for mixtures with ethanol, octyl (EMIM-OS). Let us note that the four ionic liquids (ILs) measured are miscible in water and ethanol at those temperatures and atmospheric pressure in all ranges of concentrations, but EMIM-OS jellifies for a given range of concentration with water. We compare the measured data in terms of the alkyl chain length and solvent nature. Data are compared with previously scarce results for these same systems and also for other aqueous and ethanol mixtures with ILs. In addition, we verify that our data fit the universal theoretical expression with no fitting parameters given by the pseudolattice-based Bahe–Varela model, except for IL concentrated mixtures. To fit well all ranges of concentrations, we add to the original equation two phenomenological terms with one fitting parameter each. Finally, we calculate the molar conductivity and fit it successfully with an expression derived from Onsager theory.
- 1 November 2012
- Published by Elsevier in The Journal of Chemical Thermodynamics
- Vol. 54, 68-75
Experimental evidence of the validity of Bahe–Varela theory to describe the volumetric properties of ionic liquids
- 1 November 2012
- Published by Elsevier in The Journal of Chemical Thermodynamics
- Vol. 54, 68-75
Experimental evidence of the validity of Bahe–Varela theory to describe the volumetric properties of ionic liquids
- 1 June 2012
- Published by Elsevier in The Journal of Chemical Thermodynamics
- Vol. 49, 165-171
Surface tension of four binary systems containing (1-ethyl-3-methyl imidazolium alkyl sulphate ionic liquid + water or + ethanol)
- 1 June 2012
- Published by Elsevier in The Journal of Chemical Thermodynamics
- Vol. 49, 165-171
Surface tension of four binary systems containing (1-ethyl-3-methyl imidazolium alkyl sulphate ionic liquid + water or + ethanol)
- 1 April 2012
- Published by Elsevier in The Journal of Chemical Thermodynamics
- Vol. 47, 219-222
Easy prediction of the refractive index for binary mixtures of ionic liquids with water or ethanol
- 1 April 2012
- Published by Elsevier in The Journal of Chemical Thermodynamics
- Vol. 47, 219-222
Easy prediction of the refractive index for binary mixtures of ionic liquids with water or ethanol
- 1 April 2012
- Published by Elsevier in Fluid Phase Equilibria
- Vol. 320, 1-10
Liquid–solid–liquid phase transition hysteresis loops in the ionic conductivity of ten imidazolium-based ionic liquids
- 1 April 2012
- Published by Elsevier in Fluid Phase Equilibria
- Vol. 320, 1-10
Liquid–solid–liquid phase transition hysteresis loops in the ionic conductivity of ten imidazolium-based ionic liquids