Jens Reermann
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jens Reermann has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Eckhard Quandt
Department of Materials Science, Kiel University, Kiel, Germany
6 shared publications - Michael Höft
Kiel University
5 shared publications Gerhard Schmidt
Institute for Electrical Engineering, Faculty of Engineering, Kiel University 2 , Kaiserstraße 2, 24143 Kiel, Germany
4 shared publicationsChristine Kirchhof
Institute for Materials Science, Faculty of Engineering, Kiel University 1 , Kaiserstraße 2, D-24143 Kiel, Germany
3 shared publications- Franz Faupel
Kiel University
3 shared publications - Phillip Durdaut
Chair of Microwave Engineering, Institute of Electrical Engineering and Information Technology, Faculty of Engineering, Kiel University, Kaiserstr. 2, 24143 Kiel, Germany
3 shared publications
Latest Publications
- Open Access
- 14 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 154092-154118
Navigating the Depths: A Comprehensive Survey of Deep Learning for Passive Underwater Acoustic Target Recognition
The field of deep learning is a rapidly developing research area with numerous applications across multiple domains. Sonar (SOund Navigation And Ranging) processing has traditionally been a field of statistical analysis. However, in the past ten to fifteen years, the rapid growth of deep learning has challenged classical approaches with modern deep learning-based methods. This survey provides a systematic overview of the Underwater Acoustic Target Recognition (UATR) domain within the area of deep learning. The objective is to highlight popular design choices and evaluate the commonalities and differences of the investigated techniques in relation to the selected architectures and pre-processing methods. Furthermore, this survey examines the state of UATR literature through the identification of prominent conferences and journals which points new researchers in directions where to allocate UATR related publications. Additionally, popular datasets and available benchmarks are identified and analysed for complexity coverage. This work targets researchers new to the field as well as experienced researchers that want to get a broader overview. Nonetheless, experienced sonar engineers with a strong background within classical analysis also benefit from this survey.
- 14 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 154092-154118
Open AccessNavigating the Depths: A Comprehensive Survey of Deep Learning for Passive Underwater Acoustic Target Recognition
The field of deep learning is a rapidly developing research area with numerous applications across multiple domains. Sonar (SOund Navigation And Ranging) processing has traditionally been a field of statistical analysis. However, in the past ten to fifteen years, the rapid growth of deep learning has challenged classical approaches with modern deep learning-based methods. This survey provides a systematic overview of the Underwater Acoustic Target Recognition (UATR) domain within the area of deep learning. The objective is to highlight popular design choices and evaluate the commonalities and differences of the investigated techniques in relation to the selected architectures and pre-processing methods. Furthermore, this survey examines the state of UATR literature through the identification of prominent conferences and journals which points new researchers in directions where to allocate UATR related publications. Additionally, popular datasets and available benchmarks are identified and analysed for complexity coverage. This work targets researchers new to the field as well as experienced researchers that want to get a broader overview. Nonetheless, experienced sonar engineers with a strong background within classical analysis also benefit from this survey.
- 6 May 2019
- Published by AIP Publishing in Applied Physics Letters
- Vol. 114 (18) , 183504
Influence of the quality factor on the signal to noise ratio of magnetoelectric sensors based on the delta-E effect
Recently, there has been much interest in magnetoelectric magnetic field sensors utilizing the delta-E effect. Such sensors are fully integrable and combine the advantages of high sensitivity at low frequencies with broad bandwidth. Here, we report the influence of the quality factor Q on the signal-to-noise ratio of magnetoelectric magnetic field sensors utilizing the delta-E effect. The sensor consists of a silicon cantilever covered by a magnetostrictive and a piezoelectric thin film. The magnetization-dependent elasticity of the magnetostrictive film leads to detuning of the sensor's resonance, which is excited and read out via the piezoelectric layer. The signal-to-noise ratio is experimentally analyzed as a function of the quality factor, the excitation amplitude and the signal frequency. The results are compared with a signal and noise model to describe general tendencies. The model demonstrates that, in contrast to the conventional direct operation of magnetoelectric sensors, an improvement in the limit of detection proportional to Q3/2 can be achieved if thermal-mechanical noise is dominant. The relationship still holds for frequencies far away from the resonance frequency. This reveals the potential for improving the limit of detection significantly by increasing the quality factor, if magnetic and electronic noise can be suppressed.
- 6 May 2019
- Published by AIP Publishing in Applied Physics Letters
- Vol. 114 (18) , 183504
Influence of the quality factor on the signal to noise ratio of magnetoelectric sensors based on the delta-E effect
Recently, there has been much interest in magnetoelectric magnetic field sensors utilizing the delta-E effect. Such sensors are fully integrable and combine the advantages of high sensitivity at low frequencies with broad bandwidth. Here, we report the influence of the quality factor Q on the signal-to-noise ratio of magnetoelectric magnetic field sensors utilizing the delta-E effect. The sensor consists of a silicon cantilever covered by a magnetostrictive and a piezoelectric thin film. The magnetization-dependent elasticity of the magnetostrictive film leads to detuning of the sensor's resonance, which is excited and read out via the piezoelectric layer. The signal-to-noise ratio is experimentally analyzed as a function of the quality factor, the excitation amplitude and the signal frequency. The results are compared with a signal and noise model to describe general tendencies. The model demonstrates that, in contrast to the conventional direct operation of magnetoelectric sensors, an improvement in the limit of detection proportional to Q3/2 can be achieved if thermal-mechanical noise is dominant. The relationship still holds for frequencies far away from the resonance frequency. This reveals the potential for improving the limit of detection significantly by increasing the quality factor, if magnetic and electronic noise can be suppressed.
- 17 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (11) , 4237-4249
Real-Time Biomagnetic Signal Processing for Uncooled Magnetometers in Cardiology
Despite obvious advantages over their electric counterparts, magnetic measurements are still performed very rarely for medical diagnosis. The high operating costs of established systems with a sufficient limit of detection, mainly based on superconducting quantum interference devices, prevent the spread of magnetic diagnostic procedures. Consequently, the demand for alternative low-cost magnetic sensor systems is large. Several suitable, uncooled sensor concepts exist, but their usability-especially, when operated outside magnetically shielded chambers-requires improvement. This paper highlights basic, real-time signal processing concepts, and implementations to improve the signal quality for different biomedical applications with a focus on cardiology in unshielded measurement environments. Several processing steps in the digital domain are described, such as noise reduction (by means of cancellation and suppression), adaptive sensor signal combination, and adaptive signal averaging. Finally, basic cardiologic feature extraction methods are performed using uncooled magnetometers in combination with the described signal enhancement stages.
- 17 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (11) , 4237-4249
Real-Time Biomagnetic Signal Processing for Uncooled Magnetometers in Cardiology
Despite obvious advantages over their electric counterparts, magnetic measurements are still performed very rarely for medical diagnosis. The high operating costs of established systems with a sufficient limit of detection, mainly based on superconducting quantum interference devices, prevent the spread of magnetic diagnostic procedures. Consequently, the demand for alternative low-cost magnetic sensor systems is large. Several suitable, uncooled sensor concepts exist, but their usability-especially, when operated outside magnetically shielded chambers-requires improvement. This paper highlights basic, real-time signal processing concepts, and implementations to improve the signal quality for different biomedical applications with a focus on cardiology in unshielded measurement environments. Several processing steps in the digital domain are described, such as noise reduction (by means of cancellation and suppression), adaptive sensor signal combination, and adaptive signal averaging. Finally, basic cardiologic feature extraction methods are performed using uncooled magnetometers in combination with the described signal enhancement stages.
- 20 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 18 (2) , 596-604
Noise Limits in Thin-Film Magnetoelectric Sensors With Magnetic Frequency Conversion
To enable the measurement of low-frequency magnetic signals with cantilever type thin-film magnetoelectric sensors, magnetic frequency conversion transfers the frequency of the desired signal into the mechanical resonance of the cantilever. The system electronics for the realization of this approach and the approach itself introduce additional noise sources as compared to direct detection, which lowers the limit of detection. In this paper the magnetic frequency conversion noise sources are reviewed, discussed, and evaluated for our setup. The model for the nonlinear transfer process is implemented in the time domain. This enables the consideration of the pump noise in a noise equivalent circuit. For the sensor type under investigation the dominant noise near its optimal working point originates from the pump source. If the noise of the pump can be decreased and magnetic excess noise is not dominant, the noise limit is the thermal-mechanical noise of the sensor. The implementation of a filter after the excitation source decreases the limit of detection to 60 pT/√Hz at 10 Hz.
- 20 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 18 (2) , 596-604
Noise Limits in Thin-Film Magnetoelectric Sensors With Magnetic Frequency Conversion
To enable the measurement of low-frequency magnetic signals with cantilever type thin-film magnetoelectric sensors, magnetic frequency conversion transfers the frequency of the desired signal into the mechanical resonance of the cantilever. The system electronics for the realization of this approach and the approach itself introduce additional noise sources as compared to direct detection, which lowers the limit of detection. In this paper the magnetic frequency conversion noise sources are reviewed, discussed, and evaluated for our setup. The model for the nonlinear transfer process is implemented in the time domain. This enables the consideration of the pump noise in a noise equivalent circuit. For the sensor type under investigation the dominant noise near its optimal working point originates from the pump source. If the noise of the pump can be decreased and magnetic excess noise is not dominant, the noise limit is the thermal-mechanical noise of the sensor. The implementation of a filter after the excitation source decreases the limit of detection to 60 pT/√Hz at 10 Hz.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Comparison of reference sensors for noise cancellation of magnetoelectric sensors
Thin-film magnetoelectric (ME) sensors offer a promising potential to measure biomagnetic signals in the near future. Unfortunately, this sensor type shows usually a large cross-sensitivity to all kinds of mechanic distortion due to the resonant structure. In order to overcome this problem several sensor designs have been proposed. Beside these approaches adaptive noise cancellation techniques can be used to reduce the noise coupling while keeping the sensor setup simple. In this contribution reference sensors, realized as piezoelectric cantilevers, are presented and compared to microphones by means of their feasibility to improve the signal-to-noise ratio (SNR) using adaptive cancellation approaches. If a loudspeaker is used as noise source, no crucial differences are measured. But if a vibrator is used as noise source to generate structure-borne noise, the piezoelectric (PE) cantilevers are superior. As the difference of the resonance frequencies between ME and PE sensor is decreased the SNR improvement increases at low excitation levels. In total an SNR improvement over 30 dB can be achieved.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
Comparison of reference sensors for noise cancellation of magnetoelectric sensors
Thin-film magnetoelectric (ME) sensors offer a promising potential to measure biomagnetic signals in the near future. Unfortunately, this sensor type shows usually a large cross-sensitivity to all kinds of mechanic distortion due to the resonant structure. In order to overcome this problem several sensor designs have been proposed. Beside these approaches adaptive noise cancellation techniques can be used to reduce the noise coupling while keeping the sensor setup simple. In this contribution reference sensors, realized as piezoelectric cantilevers, are presented and compared to microphones by means of their feasibility to improve the signal-to-noise ratio (SNR) using adaptive cancellation approaches. If a loudspeaker is used as noise source, no crucial differences are measured. But if a vibrator is used as noise source to generate structure-borne noise, the piezoelectric (PE) cantilevers are superior. As the difference of the resonance frequencies between ME and PE sensor is decreased the SNR improvement increases at low excitation levels. In total an SNR improvement over 30 dB can be achieved.
- 30 May 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 108 (22) , 222401
Multimode delta-E effect magnetic field sensors with adapted electrodes
We present an analytical and experimental study on low-noise piezoelectric thin film resonators that utilize the delta-E effect of a magnetostrictive layer to measure magnetic fields at low frequencies. Calculations from a physical model of the electromechanical resonator enable electrode designs to efficiently operate in the first and second transversal bending modes. As predicted by our calculations, the adapted electrode design improves the sensitivity by a factor of 6 and reduces the dynamic range of the sensor output by 16 dB, which significantly eases the requirements on readout electronics. Magnetic measurements show a bandwidth of 100 Hz at a noise level of about 100 pTHz−0.5.
- 30 May 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 108 (22) , 222401
Multimode delta-E effect magnetic field sensors with adapted electrodes
We present an analytical and experimental study on low-noise piezoelectric thin film resonators that utilize the delta-E effect of a magnetostrictive layer to measure magnetic fields at low frequencies. Calculations from a physical model of the electromechanical resonator enable electrode designs to efficiently operate in the first and second transversal bending modes. As predicted by our calculations, the adapted electrode design improves the sensitivity by a factor of 6 and reduces the dynamic range of the sensor output by 16 dB, which significantly eases the requirements on readout electronics. Magnetic measurements show a bandwidth of 100 Hz at a noise level of about 100 pTHz−0.5.
- 2 May 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 108 (18) , 182902
Electrically modulated magnetoelectric sensors
Magnetoelectric thin film composites have demonstrated their potential to detect sub-pT magnetic fields if mechanical resonances (typically few hundred Hz to a few kHz) are utilized. At low frequencies (1–100 Hz), magnetic field-induced frequency conversion has enabled wideband measurements with resonance-enhanced sensitivities by using the nonlinear characteristics of the magnetostriction curve. Nevertheless, the modulation with a magnetic field with a frequency close to the mechanical resonance results in a number of drawbacks, which are, e.g., size and energy consumption of the sensor as well as potential crosstalk in sensor arrays. In this work, we demonstrate the feasibility of an electric frequency conversion of a magnetoelectric sensor which would overcome the drawbacks of magnetic frequency conversion. This magnetoelectric sensor consists of three functional layers: an exchange biased magnetostrictive multilayer showing a high piezomagnetic coefficient without applying a magnetic bias field, a non-linear piezoelectric actuation layer and a linear piezoelectric sensing layer. In this approach, the low frequency magnetic signal is shifted into the mechanical resonance of the sensor, while the electric modulation frequency is chosen to be either the difference or the sum of the resonance and the signal frequency. Using this electric frequency conversion, a limit of detection in the low nT/Hz1/2 range was shown for signals of low frequency.
- 2 May 2016
- Published by AIP Publishing in Applied Physics Letters
- Vol. 108 (18) , 182902
Electrically modulated magnetoelectric sensors
Magnetoelectric thin film composites have demonstrated their potential to detect sub-pT magnetic fields if mechanical resonances (typically few hundred Hz to a few kHz) are utilized. At low frequencies (1–100 Hz), magnetic field-induced frequency conversion has enabled wideband measurements with resonance-enhanced sensitivities by using the nonlinear characteristics of the magnetostriction curve. Nevertheless, the modulation with a magnetic field with a frequency close to the mechanical resonance results in a number of drawbacks, which are, e.g., size and energy consumption of the sensor as well as potential crosstalk in sensor arrays. In this work, we demonstrate the feasibility of an electric frequency conversion of a magnetoelectric sensor which would overcome the drawbacks of magnetic frequency conversion. This magnetoelectric sensor consists of three functional layers: an exchange biased magnetostrictive multilayer showing a high piezomagnetic coefficient without applying a magnetic bias field, a non-linear piezoelectric actuation layer and a linear piezoelectric sensing layer. In this approach, the low frequency magnetic signal is shifted into the mechanical resonance of the sensor, while the electric modulation frequency is chosen to be either the difference or the sum of the resonance and the signal frequency. Using this electric frequency conversion, a limit of detection in the low nT/Hz1/2 range was shown for signals of low frequency.
- 13 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 16 (12) , 4891-4900
Adaptive Readout Schemes for Thin-Film Magnetoelectric Sensors Based on the delta-E Effect
Thin-film magnetoelectric sensors, i.e., composites of magnetostrictive and piezoelectric materials, are able to measure very low magnetic fields. As a consequence, an application of such sensors could be, e.g., the measurement of biomagnetic fields in the near future. To measure these signals, typically characterized by low-frequency components, techniques, such as the delta-E effect, are utilized. The limit of detection (LoD) of such sensor systems did not reach the required level until now. In order to improve this, an adaptive readout scheme is proposed for sensor systems based on the delta-E effect. The basis is a simultaneous measurement with a single sensor at different frequency ranges close to the resonance frequencies. The signals are combined optimally in regard to their signal-to-noise ratio. Two combination approaches are presented and evaluated. An improvement up to 6 dB in terms of LoD is achieved. Due to an adaption of the weighting coefficients with time, the proposed method can be interpreted as a noise reduction technique, which increases the usability of such sensors in realistic measurement scenarios.
- 13 April 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 16 (12) , 4891-4900
Adaptive Readout Schemes for Thin-Film Magnetoelectric Sensors Based on the delta-E Effect
Thin-film magnetoelectric sensors, i.e., composites of magnetostrictive and piezoelectric materials, are able to measure very low magnetic fields. As a consequence, an application of such sensors could be, e.g., the measurement of biomagnetic fields in the near future. To measure these signals, typically characterized by low-frequency components, techniques, such as the delta-E effect, are utilized. The limit of detection (LoD) of such sensor systems did not reach the required level until now. In order to improve this, an adaptive readout scheme is proposed for sensor systems based on the delta-E effect. The basis is a simultaneous measurement with a single sensor at different frequency ranges close to the resonance frequencies. The signals are combined optimally in regard to their signal-to-noise ratio. Two combination approaches are presented and evaluated. An improvement up to 6 dB in terms of LoD is achieved. Due to an adaption of the weighting coefficients with time, the proposed method can be interpreted as a noise reduction technique, which increases the usability of such sensors in realistic measurement scenarios.
- 23 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 15 (10) , 5804-5812
Adaptive Acoustic Noise Cancellation for Magnetoelectric Sensors
Sensors based on the magnetoelectric (ME) effect have the potential to be genuine alternatives for measuring bio-magnetic signals. Unfortunately, the sensor structure usually inhibits the problem that several non-magnetic types of noise couple mechanically into the sensor: in this contribution, we will focus on undesired acoustic coupling. Therefore, an adaptive cancellation approach based on a computationally efficient gradient estimation algorithm with a pseudo-optimally control scheme is proposed. The approach is using a microphone as a noise reference sensor and is implemented in real time. An evaluation in terms of measurements is performed inside a magnetically shielded chamber. For a particular scenario, which is characterized by double excitation, an algorithm with binary control-scheme improves the signal-to-noise ratio (SNR) only by around 4dB. If the proposed control scheme is used instead, an improvement of the SNR of around 13dB is achieved.
- 23 June 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 15 (10) , 5804-5812
Adaptive Acoustic Noise Cancellation for Magnetoelectric Sensors
Sensors based on the magnetoelectric (ME) effect have the potential to be genuine alternatives for measuring bio-magnetic signals. Unfortunately, the sensor structure usually inhibits the problem that several non-magnetic types of noise couple mechanically into the sensor: in this contribution, we will focus on undesired acoustic coupling. Therefore, an adaptive cancellation approach based on a computationally efficient gradient estimation algorithm with a pseudo-optimally control scheme is proposed. The approach is using a microphone as a noise reference sensor and is implemented in real time. An evaluation in terms of measurements is performed inside a magnetically shielded chamber. For a particular scenario, which is characterized by double excitation, an algorithm with binary control-scheme improves the signal-to-noise ratio (SNR) only by around 4dB. If the proposed control scheme is used instead, an improvement of the SNR of around 13dB is achieved.