Shannon T. Brown
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Shannon T. Brown has a total of 259 co-authors. Here are the top co-authors by number of shared publications:
- Steven Levin
Jet Propulsion Laboratory California Institute of Technology Pasadena CA USA
13 shared publications - Scott J. Bolton
Southwest Research Institute San Antonio TX USA
12 shared publications - Sidharth Misra
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, USA
10 shared publications - Steven C. Reising
Electrical and Computer Engineering Department, Colorado State University, Fort Collins, CO 80523, USA
9 shared publications - Michael Janssen
Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA, USA
7 shared publications - Zhimeng Zhang
California Institute of Technology Pasadena CA USA
7 shared publications
Latest Publications
- Open Access
- 22 July 2026
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 131 (7)
Io Sub‐Surface Temperature Profile Observed by the Juno Microwave Radiometer
We report on new observations of Io upwelling thermal emission over the range of 0.6–22 GHz acquired with the Juno Microwave Radiometer in December 2023 and February 2024. The microwave emission spectrum from the surface of Io is retrieved from the calibrated brightness temperatures by characterizing and removing reflections from the sky. The surface appears to exhibit specular reflection in the microwave, suggesting a relatively smooth surface on 100 km spatial scales (apart from visible topography), like Earth's land and ocean surfaces. The real part of the dielectric constant is found to be in the range of 2–4; constrained by overlapping observations on the surface from two viewing geometries. This relatively low value is consistent with a density of 0.7–1.1 g/cm 3 of the surface layer (2 . Alternately, relatively fresh lava flows (<5 years) or heat vents covered by a cooling crust on the order of 10 m over about 10% of the surface area can also explain the spectral gradient.
- 22 July 2026
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 131 (7)
Open AccessIo Sub‐Surface Temperature Profile Observed by the Juno Microwave Radiometer
We report on new observations of Io upwelling thermal emission over the range of 0.6–22 GHz acquired with the Juno Microwave Radiometer in December 2023 and February 2024. The microwave emission spectrum from the surface of Io is retrieved from the calibrated brightness temperatures by characterizing and removing reflections from the sky. The surface appears to exhibit specular reflection in the microwave, suggesting a relatively smooth surface on 100 km spatial scales (apart from visible topography), like Earth's land and ocean surfaces. The real part of the dielectric constant is found to be in the range of 2–4; constrained by overlapping observations on the surface from two viewing geometries. This relatively low value is consistent with a density of 0.7–1.1 g/cm 3 of the surface layer (2 . Alternately, relatively fresh lava flows (<5 years) or heat vents covered by a cooling crust on the order of 10 m over about 10% of the surface area can also explain the spectral gradient.
- Open Access
- 5 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing
- Vol. PP (19391404) , 1-13
Investigation of Convective Updrafts (INCUS) Dynamic Microwave Radiometer (DMR) Receiver Design and Pre-Launch Characterization
The Investigation of Convective Updrafts (INCUS) mission includes three small satellites flying in the same orbit plane with 30-120 seconds separation to study why convective storms, heavy precipitation, and clouds occur exactly when and where they form. Each satellite has a precipitation radar and one of the satellites includes a passive microwave radiometer. The Dynamic Microwave Radiometer (DMR) provides retrievals of cloud ice water path and water vapor profiles in the surrounding environment. DMR is a five-frequency millimeter-wave radiometer operating in the 87–181 GHz range. It will be deployed as part of the second spacecraft in the INCUS mission, scheduled for launch no earlier than October 2026. The DMR employs direct-detection architecture, achieving a compact design with a mass of 9.4 kg and power consumption of 10.3 W, by eliminating the need for a local oscillator and mixer. This architecture reduces system complexity while maintaining high performance. The instrument features a continuously rotating scanning reflector, enabling cross-track measurements that include views of a blackbody calibration target, the Earth over a range of incidence angles, and the cosmic microwave background radiation at 2.73 K. This configuration provides end-to-end calibration of the millimeter-wave receivers during each scan cycle. The radiometer leverages 35-nm Indium Phosphide (InP) high-electron-mobility transistor (HEMT) low-noise amplifiers (LNA) to ensure high sensitivity and precision. This paper provides an overview of the DMR's receiver design and pre-launch characterization.
- 5 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing
- Vol. PP (19391404) , 1-13
Open AccessInvestigation of Convective Updrafts (INCUS) Dynamic Microwave Radiometer (DMR) Receiver Design and Pre-Launch Characterization
The Investigation of Convective Updrafts (INCUS) mission includes three small satellites flying in the same orbit plane with 30-120 seconds separation to study why convective storms, heavy precipitation, and clouds occur exactly when and where they form. Each satellite has a precipitation radar and one of the satellites includes a passive microwave radiometer. The Dynamic Microwave Radiometer (DMR) provides retrievals of cloud ice water path and water vapor profiles in the surrounding environment. DMR is a five-frequency millimeter-wave radiometer operating in the 87–181 GHz range. It will be deployed as part of the second spacecraft in the INCUS mission, scheduled for launch no earlier than October 2026. The DMR employs direct-detection architecture, achieving a compact design with a mass of 9.4 kg and power consumption of 10.3 W, by eliminating the need for a local oscillator and mixer. This architecture reduces system complexity while maintaining high performance. The instrument features a continuously rotating scanning reflector, enabling cross-track measurements that include views of a blackbody calibration target, the Earth over a range of incidence angles, and the cosmic microwave background radiation at 2.73 K. This configuration provides end-to-end calibration of the millimeter-wave receivers during each scan cycle. The radiometer leverages 35-nm Indium Phosphide (InP) high-electron-mobility transistor (HEMT) low-noise amplifiers (LNA) to ensure high sensitivity and precision. This paper provides an overview of the DMR's receiver design and pre-launch characterization.
- Open Access
- 14 March 2026
- Published by Copernicus GmbH
Peering into the Sub-surface of Jovian Moons with Microwave Radiometry: Latest Findings from the Juno Extended Mission
The Juno Extended Mission (EM) included close fly-bys of Jupiter’s moons Ganymede, Europa and Io between 2021 – 2024. Juno carries a 6-channel microwave radiometer (MWR) operating between 0.6-22 GHz. The broad frequency range of the MWR probes successively deeper into the sub-surface of these bodies with the 0.6GHz channel probing the deepest. For Ganymede and Europa, the MWR is sensitive to the temperature from the surface to 10s of km into the ice shell over the six frequencies. For Io, the penetration is much shallower, on the order of 10s of meters maximum depth. The sub-surface temperature, dielectric and surface roughness properties are encoded in the spectra obtained by the MWR. We will provide an overview of the latest analysis of data from each moon, focusing on the new information gained from this unique planetary instrument. This includes ice shell thickness, surface/sub-surface composition and heat flow for the icy moons. For Io, the MWR data provide the latitudinal dependence of the temperature below the diurnal layer and the spectra indicate significant endogenic heating in the upper 10-20 meters that increases with latitude. The MWR was designed for observing the deep atmosphere of Jupiter but has now demonstrated unique capability for observing the sub-surface of terrestrial planets and planetary moons. From lessons learned analyzing Juno MWR data, we will discuss how future instruments could be configured specifically for targeting icy or rocky solar system bodies.
- 14 March 2026
- Published by Copernicus GmbH
Open AccessPeering into the Sub-surface of Jovian Moons with Microwave Radiometry: Latest Findings from the Juno Extended Mission
The Juno Extended Mission (EM) included close fly-bys of Jupiter’s moons Ganymede, Europa and Io between 2021 – 2024. Juno carries a 6-channel microwave radiometer (MWR) operating between 0.6-22 GHz. The broad frequency range of the MWR probes successively deeper into the sub-surface of these bodies with the 0.6GHz channel probing the deepest. For Ganymede and Europa, the MWR is sensitive to the temperature from the surface to 10s of km into the ice shell over the six frequencies. For Io, the penetration is much shallower, on the order of 10s of meters maximum depth. The sub-surface temperature, dielectric and surface roughness properties are encoded in the spectra obtained by the MWR. We will provide an overview of the latest analysis of data from each moon, focusing on the new information gained from this unique planetary instrument. This includes ice shell thickness, surface/sub-surface composition and heat flow for the icy moons. For Io, the MWR data provide the latitudinal dependence of the temperature below the diurnal layer and the spectra indicate significant endogenic heating in the upper 10-20 meters that increases with latitude. The MWR was designed for observing the deep atmosphere of Jupiter but has now demonstrated unique capability for observing the sub-surface of terrestrial planets and planetary moons. From lessons learned analyzing Juno MWR data, we will discuss how future instruments could be configured specifically for targeting icy or rocky solar system bodies.
- Open Access
- 14 March 2026
- Published by Copernicus GmbH
Distribution of Sub-surface Heating on Io
We report on new results analyzing Io’s upwelling thermal emission over the range of 0.6 to 22 GHz acquired with the Juno Microwave Radiometer (MWR) in December 2023 and February 2024. The microwave emission spectrum from the surface of Io is retrieved from the MWR calibrated brightness temperatures and represents the vertical temperature gradient in the upper 10s of meters of Io. A large spectral slope (>20K) is observed at all latitudes in the lowest frequency MWR channels suggesting significant endogenic near-surface heating. The spectral slope increases toward the north pole. We compare two end-member model fits to the MWR spectra; a conductive model and a model comprising cooling lava flows. The conductive model implies heat flows ranging from 1-3 W/m2. The alternative model of relatively fresh lava flows or heat vents covered by a cold, highly insulating crusts fits the MWR spectra with flows covering about 10% of the surface with a 3-8m thick crust. We show the regional distribution of sub-surface temperature anomalies with depth, comparing to previously catalogued hot spots, flow units and volcanic centers. We will discuss how model assumptions, such as the microwave loss tangent of the crust material and magma temperature, impact the results.
- 14 March 2026
- Published by Copernicus GmbH
Open AccessDistribution of Sub-surface Heating on Io
We report on new results analyzing Io’s upwelling thermal emission over the range of 0.6 to 22 GHz acquired with the Juno Microwave Radiometer (MWR) in December 2023 and February 2024. The microwave emission spectrum from the surface of Io is retrieved from the MWR calibrated brightness temperatures and represents the vertical temperature gradient in the upper 10s of meters of Io. A large spectral slope (>20K) is observed at all latitudes in the lowest frequency MWR channels suggesting significant endogenic near-surface heating. The spectral slope increases toward the north pole. We compare two end-member model fits to the MWR spectra; a conductive model and a model comprising cooling lava flows. The conductive model implies heat flows ranging from 1-3 W/m2. The alternative model of relatively fresh lava flows or heat vents covered by a cold, highly insulating crusts fits the MWR spectra with flows covering about 10% of the surface with a 3-8m thick crust. We show the regional distribution of sub-surface temperature anomalies with depth, comparing to previously catalogued hot spots, flow units and volcanic centers. We will discuss how model assumptions, such as the microwave loss tangent of the crust material and magma temperature, impact the results.
- Open Access
- 29 December 2025
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 131 (1)
Structure of Jupiter's High‐Latitude Storms: Folded Filamentary Regions Revealed by Juno
Sprawling, turbulent cloud formations dominate the meteorology of Jupiter's mid‐to‐high latitudes, known as Folded Filamentary Regions (FFRs). A multi‐wavelength characterization by Juno reveals the spatial distribution, vertical structure, and energetics of the FFRs. The cloud tops display multiple lobes of stratiform aerosols, separated by darker, cloud‐free lanes, and embedded with smaller eddies and high‐altitude cumulus clouds. These cyclonic FFRs are microwave‐bright in shallow‐sounding wavelengths ( bars) and microwave‐dark in deep‐sounding wavelengths ( bars), with the transition potentially associated with the water condensation layer (6–7 bars). Associating microwave contrasts with temperature anomalies, this implies despinning of cyclonic eddies above/below their mid‐planes. Despite deep roots (being detectable in wavelengths sounding bars), they are “pancake vortices” with horizontal extents at least an order of magnitude larger than their depth. In the northern hemisphere, FFRs are most common in cyclonic belts poleward of N (all latitudes are planetocentric), particularly a North Polar Filamentary Belt (NPFB) near N that defines the transition from organized belts/zones to the chaotic polar domain. This distribution explains the high lightning rates from N, peaking in a belt poleward of N, which may trace the availability of water for moist convection. Many observed lightning flashes can be associated to specific FFRs containing bright storms, but some FFRs display no activity, suggesting quiescent periods during storm evolution. Analogies to Earth's oceanic eddies suggest that cyclones deform isentropic surfaces at their midplanes, raising deep water‐rich layers upwards to promote moist convection, release latent heat, and inject clouds into the upper troposphere.
- 29 December 2025
- Published by American Geophysical Union (AGU) in Journal of Geophysical Research: Planets
- Vol. 131 (1)
Open AccessStructure of Jupiter's High‐Latitude Storms: Folded Filamentary Regions Revealed by Juno
Sprawling, turbulent cloud formations dominate the meteorology of Jupiter's mid‐to‐high latitudes, known as Folded Filamentary Regions (FFRs). A multi‐wavelength characterization by Juno reveals the spatial distribution, vertical structure, and energetics of the FFRs. The cloud tops display multiple lobes of stratiform aerosols, separated by darker, cloud‐free lanes, and embedded with smaller eddies and high‐altitude cumulus clouds. These cyclonic FFRs are microwave‐bright in shallow‐sounding wavelengths ( bars) and microwave‐dark in deep‐sounding wavelengths ( bars), with the transition potentially associated with the water condensation layer (6–7 bars). Associating microwave contrasts with temperature anomalies, this implies despinning of cyclonic eddies above/below their mid‐planes. Despite deep roots (being detectable in wavelengths sounding bars), they are “pancake vortices” with horizontal extents at least an order of magnitude larger than their depth. In the northern hemisphere, FFRs are most common in cyclonic belts poleward of N (all latitudes are planetocentric), particularly a North Polar Filamentary Belt (NPFB) near N that defines the transition from organized belts/zones to the chaotic polar domain. This distribution explains the high lightning rates from N, peaking in a belt poleward of N, which may trace the availability of water for moist convection. Many observed lightning flashes can be associated to specific FFRs containing bright storms, but some FFRs display no activity, suggesting quiescent periods during storm evolution. Analogies to Earth's oceanic eddies suggest that cyclones deform isentropic surfaces at their midplanes, raising deep water‐rich layers upwards to promote moist convection, release latent heat, and inject clouds into the upper troposphere.
- Open Access
- 15 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing
- Vol. 18 (19391404) , 27103-27112
Initial On-Orbit Performance Assessments of the Compact Ocean Wind Vector Radiometer
The Compact Ocean Wind Vector Radiometer (COWVR) is the first space-based radiometer to utilize electronic polarization basis rotation (EPBR) to measure a swath of polarimetric brightness temperatures without the need to scan the receiver electronics. The COWVR instrument also utilizes internal calibration with noise diode standards to facilitate implementation of the simplified conical-scanning radiometer design. Following successful calibration of the instrument on-orbit by the multi-agency COWVR Cal/Val team, data provided by the mission Ground Data Processing System (GDPS) was assessed. An analysis of COWVR wind speed and direction performance was performed utilizing matchups with wind retrievals from the Advanced Scatterometer (ASCAT) on Metop-B and -C. This analysis found that COWVR meets its Ocean Surface Vector Wind requirements established for the COWVR mission. Additional wind speed and direction performance assessments comparing 1) COWVR and ASCAT retrievals and 2) COWVR against the U.S. Navy's Global Environmental Model (NAVGEM) are included. Data Assimilation (DA) trials were successfully performed by assimilating the COWVR vertically- and horizontally polarized brightness temperatures data and were assessed using the Forecast Sensitivity-based Observation Impacts (FSOI).
- 15 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing
- Vol. 18 (19391404) , 27103-27112
Open AccessInitial On-Orbit Performance Assessments of the Compact Ocean Wind Vector Radiometer
The Compact Ocean Wind Vector Radiometer (COWVR) is the first space-based radiometer to utilize electronic polarization basis rotation (EPBR) to measure a swath of polarimetric brightness temperatures without the need to scan the receiver electronics. The COWVR instrument also utilizes internal calibration with noise diode standards to facilitate implementation of the simplified conical-scanning radiometer design. Following successful calibration of the instrument on-orbit by the multi-agency COWVR Cal/Val team, data provided by the mission Ground Data Processing System (GDPS) was assessed. An analysis of COWVR wind speed and direction performance was performed utilizing matchups with wind retrievals from the Advanced Scatterometer (ASCAT) on Metop-B and -C. This analysis found that COWVR meets its Ocean Surface Vector Wind requirements established for the COWVR mission. Additional wind speed and direction performance assessments comparing 1) COWVR and ASCAT retrievals and 2) COWVR against the U.S. Navy's Global Environmental Model (NAVGEM) are included. Data Assimilation (DA) trials were successfully performed by assimilating the COWVR vertically- and horizontally polarized brightness temperatures data and were assessed using the Forecast Sensitivity-based Observation Impacts (FSOI).
- 20 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Geoscience and Remote Sensing Letters
- Vol. 22 (1545598X) , 1-4
A Tone-Based Flicker Noise Mitigation Technique for Broadband Digital Microwave Radiometers
High frequency microwave and millimeter radiometers with low noise amplifier front-ends commonly suffer from gain instability, or so-called “flicker” noise. This noise has a 1/f energy spectrum and hence is also commonly referred to as 1/f noise. The effect of this noise on a passive instrument is to degrade its sensitivity and introduce post-processing calibration errors such as ‘striping’. In this paper we present a 1/f noise mitigation technique using a combination of single frequency tone injection and high spectral resolution digital signal detection. This technique can be used in radiometers with sufficient information redundancy so that a limited portion of the detected signal spectrum can be dedicated to noise mitigation. A key requirement of implementing this technique is application specific integrated circuit (ASIC) or field programmable gate array (FPGA)-based spectral decomposition of the radio frequency energy. A proof-of-concept hardware setup and signal processing steps required to implement such a technique are presented in this paper. Measurements presented here show a reduction up to 87 % in 1/f noise energy using this technique and are applicable to airborne and ground-based instruments.
- 20 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Geoscience and Remote Sensing Letters
- Vol. 22 (1545598X) , 1-4
A Tone-Based Flicker Noise Mitigation Technique for Broadband Digital Microwave Radiometers
High frequency microwave and millimeter radiometers with low noise amplifier front-ends commonly suffer from gain instability, or so-called “flicker” noise. This noise has a 1/f energy spectrum and hence is also commonly referred to as 1/f noise. The effect of this noise on a passive instrument is to degrade its sensitivity and introduce post-processing calibration errors such as ‘striping’. In this paper we present a 1/f noise mitigation technique using a combination of single frequency tone injection and high spectral resolution digital signal detection. This technique can be used in radiometers with sufficient information redundancy so that a limited portion of the detected signal spectrum can be dedicated to noise mitigation. A key requirement of implementing this technique is application specific integrated circuit (ASIC) or field programmable gate array (FPGA)-based spectral decomposition of the radio frequency energy. A proof-of-concept hardware setup and signal processing steps required to implement such a technique are presented in this paper. Measurements presented here show a reduction up to 87 % in 1/f noise energy using this technique and are applicable to airborne and ground-based instruments.
- Open Access
- 18 March 2025
- Published by Copernicus GmbH
Io’s Sub-surface Heat Distribution Observed by the Juno Microwave Radiometer
The NASA Juno mission performed two close fly-bys of Jupiter’s moon Io on December 30, 2023 and February 3, 2024. Juno carries a 6-channel microwave radiometer (MWR) operating between 0.6-22 GHz. The first fly-by observed Io’s north pole and the 2nd pass mapped latitudes within +/- 45o on the Jovian facing hemisphere. The broad frequency range of the MWR probes successively deeper into the Io sub-surface with the 0.6GHz channel probing the deepest. The penetration depth into the sub-surface of the highest frequency channels is on the order of centimeters and the lowest frequency on the order of several 10s of meters. We find the surface of Io generally exhibits specular scattering properties over the 0.6-22 GHz frequency range. We use overlapping observations from the two fly-bys that observe the same areas at different incidence angles and polarizations to solve for the surface dielectric properties. We find the surface dielectric (real part) to be between 2-3, which is consistent with a low-density material. We use the MWR derived real part of the dielectric constant (reflection) with Earth analogs for the imaginary part (loss) to derive the sub-surface temperature profile by inverting the radiative transfer equation. We find the near-surface temperatures decrease with increasing latitude and are coldest at the north pole, consistent with prior infrared observations of the surface skin temperature. We find a strong sub-surface thermal gradient, on the order of 20-40K, over all regions observed by MWR. The sub-surface thermal anomaly is not spatially uniform. We fit several possible models to explain this gradient. One possible explanation are spatially distributed near-surface heat vents topped by a cooled crust, which fit the MWR spectra if they occupy 5-10% of the surface area. We will give an overview of the MWR observations and inferences about the sub-surface thermal and compositional properties.
- 18 March 2025
- Published by Copernicus GmbH
Open AccessIo’s Sub-surface Heat Distribution Observed by the Juno Microwave Radiometer
The NASA Juno mission performed two close fly-bys of Jupiter’s moon Io on December 30, 2023 and February 3, 2024. Juno carries a 6-channel microwave radiometer (MWR) operating between 0.6-22 GHz. The first fly-by observed Io’s north pole and the 2nd pass mapped latitudes within +/- 45o on the Jovian facing hemisphere. The broad frequency range of the MWR probes successively deeper into the Io sub-surface with the 0.6GHz channel probing the deepest. The penetration depth into the sub-surface of the highest frequency channels is on the order of centimeters and the lowest frequency on the order of several 10s of meters. We find the surface of Io generally exhibits specular scattering properties over the 0.6-22 GHz frequency range. We use overlapping observations from the two fly-bys that observe the same areas at different incidence angles and polarizations to solve for the surface dielectric properties. We find the surface dielectric (real part) to be between 2-3, which is consistent with a low-density material. We use the MWR derived real part of the dielectric constant (reflection) with Earth analogs for the imaginary part (loss) to derive the sub-surface temperature profile by inverting the radiative transfer equation. We find the near-surface temperatures decrease with increasing latitude and are coldest at the north pole, consistent with prior infrared observations of the surface skin temperature. We find a strong sub-surface thermal gradient, on the order of 20-40K, over all regions observed by MWR. The sub-surface thermal anomaly is not spatially uniform. We fit several possible models to explain this gradient. One possible explanation are spatially distributed near-surface heat vents topped by a cooled crust, which fit the MWR spectra if they occupy 5-10% of the surface area. We will give an overview of the MWR observations and inferences about the sub-surface thermal and compositional properties.
- Open Access
- 18 March 2025
- Published by Copernicus GmbH
Potential for Remote Sensing of Precipitation using the Dynamic Microwave Radiometer on the NASA INCUS Mission based on the Heritage of TEMPEST Scientific Results
The INvestigation of Convective UpdraftS (INCUS) is a NASA Earth Venture mission (EVM-3) that will provide the first global systematic investigation into convective mass flux, the vertical transport of air and water, and its evolution within deep tropical convection. The overarching goal of the INCUS mission is to understand why, when and where tropical convective storms form, and why only some storms produce extreme weather. INCUS is led by PI Susan van den Heever of Colorado State University (CSU), in collaboration with NASA/Jet Propulsion Laboratory (JPL), Blue Canyon Technologies, and Tendeg Systems. INCUS consists of a series of three small satellites flying in formation, each carrying a Ka-band radar based on RainCube and one cross-track scanning radiometer based on TEMPEST. A novel time-differencing approach among the three satellites flown in close succession (30, and 90, and 120 seconds apart) will provide the first estimates of convective mass flux across the tropics.The success of the INCUS EVM-3 proposal to NASA relied on the prior success of two pathfinder CubeSat missions: RainCube, the first weather radar on a CubeSat, led by NASA/JPL, and the Temporal Experiment for Storms and Tropical Systems – Demonstration (TEMPEST-D) mission, led by CSU, producing the first global (up to 58 degrees latitude) observations from a multi-frequency microwave radiometer on a CubeSat, operating for nearly three years in LEO.TEMPEST-D, a NASA Earth Venture Technology mission, produced global atmospheric science data, a well-calibrated, highly stable radiometer over three years of operations. TEMPEST-D brightness temperatures were validated using scientific and operational microwave sensors, including GPM/GMI and four MHS sensors, operating at similar frequencies to TEMPEST-D channels at 87, 164, 174, 178 and 181 GHz. Using the double-difference approach, TEMPEST-D performance was shown to be comparable to or better than much larger scientific and operational sensors, in calibration accuracy, precision, stability and instrument noise, during its nearly 3-year mission.A duplicate TEMPEST sensor produced alongside TEMPEST-D was integrated with the Compact Ocean Wind Vector Radiometer (COWVR) from NASA/JPL and launched by the U.S. Space Force to demonstrate low-cost space technologies to improve global weather forecasting. COWVR/TEMPEST were launched on the STP-H8 mission on December 21, 2021, and have performed coordinated observations of Earth’s oceans and atmosphere from the ISS since January 7, 2022. Retrievals of water vapor profiles, clouds, and precipitation from COWVR/TEMPEST-H8 are being performed in collaboration between JPL and CSU.Previous studies have validated the accuracy and precision of TEMPEST-D brightness temperatures using clear-sky oceanic observations. Recent advances extended the validation of TEMPEST-D and TEMPEST-H8 brightness temperature observations over tropical cyclones using GPM/GMI brightness temperatures and GPM/DPR vertical cumulative reflectivity. Prior studies demonstrated accurate quantitative precipitation estimation using machine learning over CONUS. Recent advances expanded this capability to a global basis using GPM/GMI and AMSR-2 datasets for training and validation and IMERG rain rates for cross comparison. The heritage of TEMPEST-D and TEMPEST-H8 will be used to demonstrate the potential for remote sensing of precipitation from the Dynamic Microwave Radiometer on the INCUS mission.
- 18 March 2025
- Published by Copernicus GmbH
Open AccessPotential for Remote Sensing of Precipitation using the Dynamic Microwave Radiometer on the NASA INCUS Mission based on the Heritage of TEMPEST Scientific Results
The INvestigation of Convective UpdraftS (INCUS) is a NASA Earth Venture mission (EVM-3) that will provide the first global systematic investigation into convective mass flux, the vertical transport of air and water, and its evolution within deep tropical convection. The overarching goal of the INCUS mission is to understand why, when and where tropical convective storms form, and why only some storms produce extreme weather. INCUS is led by PI Susan van den Heever of Colorado State University (CSU), in collaboration with NASA/Jet Propulsion Laboratory (JPL), Blue Canyon Technologies, and Tendeg Systems. INCUS consists of a series of three small satellites flying in formation, each carrying a Ka-band radar based on RainCube and one cross-track scanning radiometer based on TEMPEST. A novel time-differencing approach among the three satellites flown in close succession (30, and 90, and 120 seconds apart) will provide the first estimates of convective mass flux across the tropics.The success of the INCUS EVM-3 proposal to NASA relied on the prior success of two pathfinder CubeSat missions: RainCube, the first weather radar on a CubeSat, led by NASA/JPL, and the Temporal Experiment for Storms and Tropical Systems – Demonstration (TEMPEST-D) mission, led by CSU, producing the first global (up to 58 degrees latitude) observations from a multi-frequency microwave radiometer on a CubeSat, operating for nearly three years in LEO.TEMPEST-D, a NASA Earth Venture Technology mission, produced global atmospheric science data, a well-calibrated, highly stable radiometer over three years of operations. TEMPEST-D brightness temperatures were validated using scientific and operational microwave sensors, including GPM/GMI and four MHS sensors, operating at similar frequencies to TEMPEST-D channels at 87, 164, 174, 178 and 181 GHz. Using the double-difference approach, TEMPEST-D performance was shown to be comparable to or better than much larger scientific and operational sensors, in calibration accuracy, precision, stability and instrument noise, during its nearly 3-year mission.A duplicate TEMPEST sensor produced alongside TEMPEST-D was integrated with the Compact Ocean Wind Vector Radiometer (COWVR) from NASA/JPL and launched by the U.S. Space Force to demonstrate low-cost space technologies to improve global weather forecasting. COWVR/TEMPEST were launched on the STP-H8 mission on December 21, 2021, and have performed coordinated observations of Earth’s oceans and atmosphere from the ISS since January 7, 2022. Retrievals of water vapor profiles, clouds, and precipitation from COWVR/TEMPEST-H8 are being performed in collaboration between JPL and CSU.Previous studies have validated the accuracy and precision of TEMPEST-D brightness temperatures using clear-sky oceanic observations. Recent advances extended the validation of TEMPEST-D and TEMPEST-H8 brightness temperature observations over tropical cyclones using GPM/GMI brightness temperatures and GPM/DPR vertical cumulative reflectivity. Prior studies demonstrated accurate quantitative precipitation estimation using machine learning over CONUS. Recent advances expanded this capability to a global basis using GPM/GMI and AMSR-2 datasets for training and validation and IMERG rain rates for cross comparison. The heritage of TEMPEST-D and TEMPEST-H8 will be used to demonstrate the potential for remote sensing of precipitation from the Dynamic Microwave Radiometer on the INCUS mission.