Rachid Chenni

Renewable Energy Resources (RES) can supply a clean and a smart solution to satisfy the rapidly growing load demand. The Photovoltaic (PV) and wind turbines are considered as resources of Distributed Generation (DG). The integration of PV - DG units into distribution systems has a significant effect on reducing the system active power losses. In this paper, a new technique based on the Moth Flame Optimization (MFO) algorithm, is used to optimally allocate the PV -DG units in Radial Distribution Systems (RDSs) and determine the optimal size of each unit. The objective of the technique is to minimize the total active power losses of the system, while satisfying several operating constraints. The proposed optimization algorithm is tested using three different IEEE standard RDSs of various sizes, which are 33, 69 and 118-bus systems. In order to demonstrate the applicability and the performance of the MFO algorithm, numerical simulations are obtained when applying the MFO algorithm, and compared with different existing optimization techniques. This comparison shows the validity of the proposed MFO algorithm.

An Accurate Photovoltaic Emulator Based on Two Closed-Loop Control Systems Including Partial Shading Conditions

With the continuous growth of energy consumption, the rationalization of energy has become a priority. The photovoltaic energy sector remains a major occupation for researchers in the field of production optimization or storage methods. The concept developed in this work is a mixed optimization approach for energy management during battery charging with a duty cycle. A selective collaborative algorithm intervenes to choose and use the appropriate results of the few techniques to optimize the charging time of a battery and estimate its state of charge by using the minimum possible tools. This is done using a collective database that is accessible in real time. It also effectively allows the synchronization of information between several customers. This approach is performed on a mobile application on android, through a Google Firebase platform that allows us to secure collaborative access between multiple customers and use the results of the calculations of some algorithms. It gives us the values obtained by the various sensors in real time to accelerate the charging speed of the battery. The validation of this approach led us to practice a few scenarios using an Arduino board to show that this approach has a better performance.

A Combined MPPT Algorithm for Photovoltaic Systems Based Arduino Microcontroller

Photovoltaic pumping is considered to be the most used application amongst other photovoltaic energy applications in isolated sites. This technology is developing with a slow progression to allow the photovoltaic system to operate at its maximum power. This work introduces the modified algorithm which is a perturb and observe (P&O) type to overcome the limitations of the conventional P&O algorithm and increase its global performance in abrupt weather condition changes. The most significant conventional P&O algorithm restriction is the difficulty faced when choosing the variable step of the reference voltage value, a good compromise between the swift dynamic response and the stability in the steady state. To adjust the step reference voltage according to the location of the operating point of the maximum power point (MPP), a fuzzy logic controller (FLC) block adapted to the P&O algorithm is used. This allows the improvement of the tracking pace and the steady state oscillation elimination. The suggested method was evaluated by simulation using MATLAB/SimPowerSystems blocks and compared to the classical P&O under different irradiation levels. The results obtained show the effectiveness of the technique proposed and its capacity for the practical and efficient tracking of maximum power.

The interest of the research technique of maximum power point tracking, exposed by this article, lays in the fact of work instantly on the real characteristic of the photovoltaic module. This work is based on instantaneous measurements of its terminals’ current & voltage as well as the exploitation of the characteristic “Power - Duty Cycle” to define rapidly the Duty cycle in which power reaches its maximum value. To ensure instantaneous tracking of the point of maximum power, we use “DC/DC Converter” based on “Pulse Wave Modulation’s (PWM) Command” controlled by an algorithm implanted in a microcontroller’s memory. This algorithm responds to the quick changes in climate (sunlight and temperature). To identify the control parameters “V_PV & I_PV” at any change in operating conditions, sensors are projected. this algorithm applied to the Duty cycle of the static converter enables the control of power supplied by the photovoltaic generator thanks to oscillatory movement around the MPP. Our article highlights the importance of this technique which lays in its simplicity and performance in changing climatic conditions. This efficiency is confirmed by experimental tests and this technique will improve its predecessors.

This paper introduces a survey of a maximum peak power tracking (MPPT). Techniques used in the implementation photovoltaic power systems. It discusses different 40 techniques used in tracking maximum power in PV arrays.