Chodchanok Attaphong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chodchanok Attaphong has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
David A. Sabatini
School of Civil Engineering and Environmental Science University of Oklahoma Norman OK USA
5 shared publicationsAmpira Charoensaeng
The Petroleum and Petrochemical College Chulalongkorn University Bangkok Thailand
3 shared publications- David A. Sabatini
School of Civil Engineering and Environmental Science, University of Oklahoma, Norman, OK 73019, USA
3 shared publications Sutha Khaodhiar
Department of Environmental Engineering, Faculty of Engineering Chulalongkorn University Bangkok Thailand
3 shared publicationsLinh D. Do
2 shared publications- Nattaya Morawan2 shared publications
Latest Publications
- Open Access
- 14 May 2026
- Published by Elsevier in Chemical Engineering Journal Advances
- Vol. 26
Optimization of chemical precipitation for valuable metal recovery from spent lithium nickel manganese cobalt oxide batteries
- 14 May 2026
- Published by Elsevier in Chemical Engineering Journal Advances
- Vol. 26
Open AccessOptimization of chemical precipitation for valuable metal recovery from spent lithium nickel manganese cobalt oxide batteries
- Open Access
- 2 February 2026
- Published by Elsevier in SSRN Electronic Journal
Environmental Impact Assessment of Palm Oil-Based Microemulsion Biofuels
Palm oil-based microemulsification has been recently studied and utilized for modifying the viscosity of biofuels to solve the diesel engine knocking problem. This study aimed to assess the environmental impacts of palm oil-based microemulsion biofuels with and without a co-surfactant from the primary results of fuel properties and engine tests, compared with the two basic fuels (commercial-grade diesel and palm oil-based biodiesel). According to the results of the one-hour engine test, the environmental impact assessment revealed that the three highest environmental impacts of microemulsion biofuels were human carcinogenic toxicity, fossil resource scarcity, and marine eutrophication. Palm oil was the main fuel component that affected the environmental impacts of both microemulsion biofuels, primarily due to its production process. Although both microemulsion biofuels have had negative impacts on the environment, a comparative analysis of all fuels still revealed that they released a lower negative impact than basic fuels in some categories, especially in marine eutrophication and fossil resource scarcity. In terms of cost, microemulsion biofuels were more expensive than basic fuels due to the cost of high-grade alcohol used. However, cost reductions could be achieved by substituting alcohol produced from local feedstocks. These findings revealed that palm oil-based microemulsion biofuels, with and without a co-surfactant, have the potential to serve as alternative fuels with palm oil adaptation.
- 2 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEnvironmental Impact Assessment of Palm Oil-Based Microemulsion Biofuels
Palm oil-based microemulsification has been recently studied and utilized for modifying the viscosity of biofuels to solve the diesel engine knocking problem. This study aimed to assess the environmental impacts of palm oil-based microemulsion biofuels with and without a co-surfactant from the primary results of fuel properties and engine tests, compared with the two basic fuels (commercial-grade diesel and palm oil-based biodiesel). According to the results of the one-hour engine test, the environmental impact assessment revealed that the three highest environmental impacts of microemulsion biofuels were human carcinogenic toxicity, fossil resource scarcity, and marine eutrophication. Palm oil was the main fuel component that affected the environmental impacts of both microemulsion biofuels, primarily due to its production process. Although both microemulsion biofuels have had negative impacts on the environment, a comparative analysis of all fuels still revealed that they released a lower negative impact than basic fuels in some categories, especially in marine eutrophication and fossil resource scarcity. In terms of cost, microemulsion biofuels were more expensive than basic fuels due to the cost of high-grade alcohol used. However, cost reductions could be achieved by substituting alcohol produced from local feedstocks. These findings revealed that palm oil-based microemulsion biofuels, with and without a co-surfactant, have the potential to serve as alternative fuels with palm oil adaptation.
- 24 March 2023
- Published by Wiley in Journal of Surfactants and Detergents
- Vol. 26 (3) , 335-344
Phase stability, fuel properties, and diesel engine performance of palm‐oil‐based microemulsion biofuels
Microemulsification and blending are two viscosity‐modifying techniques of vegetable oils for direct use with diesel engine. In this study, alcohol blends are mixtures of ethanol, diesel, and palm‐oil biodiesel while microemulsion biofuels are thermodynamically stable, clear, and single‐phase mixtures of diesel, palm oil, and ethanol stabilized by surfactants and cosurfactants. Although there are many studies on biofuels lately, there is limited research on using biodiesel as a surfactant in microemulsion formulations and applied on engine performance at different engine loads. Therefore, the objectives are to investigate phase stability and fuel properties of formulated biofuels (various blends and microemulsions), to determine the engine performance at different engine loads (no load, and from 0.5 to 2.0 kW), and to estimate laboratory‐scale cost of the selected biofuels compared to diesel and biodiesel. The results showed that phase stability and fuel properties of selected microemulsion biofuels are comparable to diesel and biodiesel. These microemulsion biofuels can be applied to the diesel engine at different loads while diesel‐ethanol blends and palm‐oil‐biodiesel‐ethanol blends cannot be. It was found that the energy efficiencies of the system using microemulsion biofuels were slightly lower than the average energy efficiency of diesel engine. From this study, it can be summarized that microemulsion biofuels can be formulated using palm‐oil biodiesel (palm‐oil methyl ester) as a bio‐based surfactant and they can be considered as environmentally‐friendly alternatives to diesel and biodiesel. However, cost considerations showed that the raw materials should be locally available to reduce additional costs of microemulsion biofuels.
- 24 March 2023
- Published by Wiley in Journal of Surfactants and Detergents
- Vol. 26 (3) , 335-344
Phase stability, fuel properties, and diesel engine performance of palm‐oil‐based microemulsion biofuels
Microemulsification and blending are two viscosity‐modifying techniques of vegetable oils for direct use with diesel engine. In this study, alcohol blends are mixtures of ethanol, diesel, and palm‐oil biodiesel while microemulsion biofuels are thermodynamically stable, clear, and single‐phase mixtures of diesel, palm oil, and ethanol stabilized by surfactants and cosurfactants. Although there are many studies on biofuels lately, there is limited research on using biodiesel as a surfactant in microemulsion formulations and applied on engine performance at different engine loads. Therefore, the objectives are to investigate phase stability and fuel properties of formulated biofuels (various blends and microemulsions), to determine the engine performance at different engine loads (no load, and from 0.5 to 2.0 kW), and to estimate laboratory‐scale cost of the selected biofuels compared to diesel and biodiesel. The results showed that phase stability and fuel properties of selected microemulsion biofuels are comparable to diesel and biodiesel. These microemulsion biofuels can be applied to the diesel engine at different loads while diesel‐ethanol blends and palm‐oil‐biodiesel‐ethanol blends cannot be. It was found that the energy efficiencies of the system using microemulsion biofuels were slightly lower than the average energy efficiency of diesel engine. From this study, it can be summarized that microemulsion biofuels can be formulated using palm‐oil biodiesel (palm‐oil methyl ester) as a bio‐based surfactant and they can be considered as environmentally‐friendly alternatives to diesel and biodiesel. However, cost considerations showed that the raw materials should be locally available to reduce additional costs of microemulsion biofuels.
- 19 November 2018
- Published by Wiley in Journal of Surfactants and Detergents
- Vol. 22 (5) , 1175-1187
Cold Water Detergency of Triacylglycerol Semisolid Soils: The Effect of Salinity, Alcohol Type, and Surfactant Systems
Cold water detergency of triacylglycerol semisolid soils is much more challenging than liquid vegetable oils due to poorer interaction between surfactants and semisolid soil. This research seeks to improve the removal efficiency of semisolid soils below their melting points using surfactant‐based formulations containing different alcohol additives. To this end, cold water detergency of solid coconut oil and solid palm kernel oil was investigated in various surfactant/alcohol systems, including single anionic extended surfactants, single nonionic alcohol ethoxylate surfactants, and a mixture of anionic surfactants. A series of alcohols (2‐butanol, 1‐hexanol, 1‐heptanol, 1‐octanol, 1‐nonanol, and 1‐decanol) were added to the surfactant formulations to investigate cold water detergency improvement. While cold water detergency using surfactants alone was poor, it was considerably improved when optimum salinity (S*) and 1‐heptanol, 1‐octanol, or 1‐nonanol were introduced to the studied surfactant formulations. The maximum detergency of solid coconut oil exceeded 90% removal in the 0.1 w/v% C14‐15‐8PO‐SO4Na/0.2 w/v% 1‐octanol/4 w/v% NaCl system (a final optimized surfactant system) at a washing temperature of 10°C versus 22.9 ± 2.2% in the surfactant alone (not at optimum salinity and no additive). Further analysis showed that improved cold water detergency using surfactant/intermediate‐chain alcohols/NaCl could be correlated with high wettability (low contact angle) as well as favorable surfactant system‐soil interaction as observed by lower interfacial tension values. In contrast, the improved cold water detergency was observed to be independent of dispersion stability. This work thus demonstrates that surfactant system design, including additives, can improve cold water detergency of semisolid soils and should be further explored in future research.
- 19 November 2018
- Published by Wiley in Journal of Surfactants and Detergents
- Vol. 22 (5) , 1175-1187
Cold Water Detergency of Triacylglycerol Semisolid Soils: The Effect of Salinity, Alcohol Type, and Surfactant Systems
Cold water detergency of triacylglycerol semisolid soils is much more challenging than liquid vegetable oils due to poorer interaction between surfactants and semisolid soil. This research seeks to improve the removal efficiency of semisolid soils below their melting points using surfactant‐based formulations containing different alcohol additives. To this end, cold water detergency of solid coconut oil and solid palm kernel oil was investigated in various surfactant/alcohol systems, including single anionic extended surfactants, single nonionic alcohol ethoxylate surfactants, and a mixture of anionic surfactants. A series of alcohols (2‐butanol, 1‐hexanol, 1‐heptanol, 1‐octanol, 1‐nonanol, and 1‐decanol) were added to the surfactant formulations to investigate cold water detergency improvement. While cold water detergency using surfactants alone was poor, it was considerably improved when optimum salinity (S*) and 1‐heptanol, 1‐octanol, or 1‐nonanol were introduced to the studied surfactant formulations. The maximum detergency of solid coconut oil exceeded 90% removal in the 0.1 w/v% C14‐15‐8PO‐SO4Na/0.2 w/v% 1‐octanol/4 w/v% NaCl system (a final optimized surfactant system) at a washing temperature of 10°C versus 22.9 ± 2.2% in the surfactant alone (not at optimum salinity and no additive). Further analysis showed that improved cold water detergency using surfactant/intermediate‐chain alcohols/NaCl could be correlated with high wettability (low contact angle) as well as favorable surfactant system‐soil interaction as observed by lower interfacial tension values. In contrast, the improved cold water detergency was observed to be independent of dispersion stability. This work thus demonstrates that surfactant system design, including additives, can improve cold water detergency of semisolid soils and should be further explored in future research.
- 9 October 2015
- Published by Taylor & Francis in International Journal of Green Energy
- Vol. 13 (9) , 930-943
Phase behaviors, fuel properties, and combustion characteristics of alcohol-vegetable oil-diesel microemulsion fuels
Biofuels are being considered as alternatives to fossil-based fuels due to depletion of petroleum-based reserves and pollutant emission concerns. Vegetable oils and bioalcohols have proven to be viable alternative fuels both with and without engine modification. However, high viscosity and low energy content are long-term operational problems with vegetable oils and bioalcohols, respectively. Therefore, vegetable oil-based microemulsification is being evaluated as a method to reduce the high viscosity of vegetable oils and enhance the miscibility of alcohol and oil phases. Studies have shown that microemulsification with different alcohols lead to varying fuel properties depending on their structure. The overall goal of this study was to formulate microemulsion fuels with single and mixed alcohol systems by determining the effects of water content, alcohol branching structure and carbon chain length on phase behaviors, fuel properties, and emission characteristics. It was found that microemulsion fuels using certain alcohols displayed favorable stability, properties, and emission characteristics. Flames of fuels with linear short-chain-length alcohols had larger near-burner blue regions and lower CO and soot emissions indicating the occurrence of more complete combustion. In addition to alcohol effects, the effect of vegetable oils, surfactants, and additives on emission characteristics were insightful in pursuit of appropriate microemulsion fuels as cleaner burning alternatives to both No.2 diesel and canola biodiesel.
- 9 October 2015
- Published by Taylor & Francis in International Journal of Green Energy
- Vol. 13 (9) , 930-943
Phase behaviors, fuel properties, and combustion characteristics of alcohol-vegetable oil-diesel microemulsion fuels
Biofuels are being considered as alternatives to fossil-based fuels due to depletion of petroleum-based reserves and pollutant emission concerns. Vegetable oils and bioalcohols have proven to be viable alternative fuels both with and without engine modification. However, high viscosity and low energy content are long-term operational problems with vegetable oils and bioalcohols, respectively. Therefore, vegetable oil-based microemulsification is being evaluated as a method to reduce the high viscosity of vegetable oils and enhance the miscibility of alcohol and oil phases. Studies have shown that microemulsification with different alcohols lead to varying fuel properties depending on their structure. The overall goal of this study was to formulate microemulsion fuels with single and mixed alcohol systems by determining the effects of water content, alcohol branching structure and carbon chain length on phase behaviors, fuel properties, and emission characteristics. It was found that microemulsion fuels using certain alcohols displayed favorable stability, properties, and emission characteristics. Flames of fuels with linear short-chain-length alcohols had larger near-burner blue regions and lower CO and soot emissions indicating the occurrence of more complete combustion. In addition to alcohol effects, the effect of vegetable oils, surfactants, and additives on emission characteristics were insightful in pursuit of appropriate microemulsion fuels as cleaner burning alternatives to both No.2 diesel and canola biodiesel.
- 14 December 2014
- Published by Wiley in Journal of Surfactants and Detergents
- Vol. 18 (3) , 373-382
Detergency of Vegetable Oils and Semi‐Solid Fats Using Microemulsion Mixtures of Anionic Extended Surfactants: The HLD Concept and Cold Water Applications
In spite of the increasing interest in cold temperature detergency of vegetable oils and fats, very limited research has been published on this topic. Extended surfactants have recently been shown to produce very promising detergency with vegetable oils at ambient temperature. However, the excessive salinity requirement (4–14 %) for these surfactants has limited their use in practical applications. In this work, we investigated the mixture of a linear C10–18PO–2EO–NaSO4 extended surfactant and a hydrophobic twin‐tailed sodium dioctyl sulfosuccinate surfactant for cold temperature detergency of vegetable oils and semi‐solid fats. Four vegetable oils of varying melting points (from −10 to 28 °C) were studied, these were canola, jojoba, coconut and palm kernel oils. Anionic surfactant mixtures showed synergism in detergency performance compared to single surfactant systems. At temperatures above the melting point, greater than 90 % detergency was achieved at 0.5 % NaCl. While detergency performance decreased at temperatures below the melting point, it was still superior to that of a commercial detergent (up to 80 vs. 40 %). Further, results show that the experimental microemulsion phase behaviors correlated very well with predictions from the hydrophilic–lipophilic deviation concept.
- 14 December 2014
- Published by Wiley in Journal of Surfactants and Detergents
- Vol. 18 (3) , 373-382
Detergency of Vegetable Oils and Semi‐Solid Fats Using Microemulsion Mixtures of Anionic Extended Surfactants: The HLD Concept and Cold Water Applications
In spite of the increasing interest in cold temperature detergency of vegetable oils and fats, very limited research has been published on this topic. Extended surfactants have recently been shown to produce very promising detergency with vegetable oils at ambient temperature. However, the excessive salinity requirement (4–14 %) for these surfactants has limited their use in practical applications. In this work, we investigated the mixture of a linear C10–18PO–2EO–NaSO4 extended surfactant and a hydrophobic twin‐tailed sodium dioctyl sulfosuccinate surfactant for cold temperature detergency of vegetable oils and semi‐solid fats. Four vegetable oils of varying melting points (from −10 to 28 °C) were studied, these were canola, jojoba, coconut and palm kernel oils. Anionic surfactant mixtures showed synergism in detergency performance compared to single surfactant systems. At temperatures above the melting point, greater than 90 % detergency was achieved at 0.5 % NaCl. While detergency performance decreased at temperatures below the melting point, it was still superior to that of a commercial detergent (up to 80 vs. 40 %). Further, results show that the experimental microemulsion phase behaviors correlated very well with predictions from the hydrophilic–lipophilic deviation concept.
- 7 October 2013
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 27 (11) , 6773-6780
Phase Behaviors of Vegetable Oil-Based Microemulsion Fuels: The Effects of Temperatures, Surfactants, Oils, and Water in Ethanol
- 7 October 2013
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 27 (11) , 6773-6780
Phase Behaviors of Vegetable Oil-Based Microemulsion Fuels: The Effects of Temperatures, Surfactants, Oils, and Water in Ethanol