Wolfdietrich Meyer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Wolfdietrich Meyer has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Hadi Bakhshi
Department of Life Science and Bioprocesses, Fraunhofer Institute for Applied Polymer Research IAP, Geiselbergstraße 69, 14476 Potsdam, Germany
3 shared publications Hartmut Krüger
Department of Functional Polymer Systems, Fraunhofer Institute for Applied Polymer Research IAP Geiselbergstraße 68, 14476 Potsdam-Golm, (Germany)
3 shared publications- Petra Juliane Kluger
University of Stuttgart
3 shared publications - Ali Salimi
Iran Polymer and Petrochemical Institute
2 shared publications Esther C. Novosel
Institute for Interfacial Engineering IGVT, University of Stuttgart Nobelstraße 12, 70569 Stuttgart, (Germany)
2 shared publicationsGünter E. M. Tovar
Fraunhofer Institute for Interfacial Engineering and Biotechnology Nobelstraße 12, 70569 Stuttgart, (Germany)
2 shared publications
Latest Publications
- Open Access
- 17 October 2026
- Published by Elsevier in Machine Learning with Applications
- Vol. 26
Reuse quality of open polymer datasets: a reproducible cross-repository audit (2020–2025)
- 17 October 2026
- Published by Elsevier in Machine Learning with Applications
- Vol. 26
Open AccessReuse quality of open polymer datasets: a reproducible cross-repository audit (2020–2025)
- Open Access
Photocurable Crosslinker from Bio-Based Non-Isocyanate Poly(hydroxyurethane) for Biocompatible Hydrogels
This study explores the synthesis of photocurable non-isocyanate polyhydroxyethylurethanes (BPHUs) derived from renewable sources, designed for biomedical applications and the development towards advanced light curing processes. The following two pathways were developed: an aliphatic route using 1,4-butanediol-derived cyclic carbonates and an aromatic route with resorcinol-based carbonates. Ring-opening polymerization with dodecanediamine produced BPHU intermediates, which were methacrylated to form photoreactive derivatives (aliphatic MAs and aromatic MAs). Comprehensive characterization, including NMR, GPC, and FTIR, confirmed the successful synthesis. The UV curing of these methacrylated compounds yielded hydrogels with swelling properties. Aliphatic BPHUs achieved a gel content of 91.3% and a swelling of 1057%, demonstrating the flexibility and UV stability suitable for adaptable biomedical applications. Conversely, aromatic BPHUs displayed a gel content of 78.1% and a swelling of 3304%, indicating higher rigidity, which is advantageous for load-bearing uses. Cytotoxicity assessments adhering to the DIN EN ISO 10993-5 standard demonstrated non-cytotoxicity, with an >80% cell viability for both variants. This research underscores the potential of green chemistry in crafting biocompatible, versatile BPHUs, paving the way for eco-friendly materials in implantable medical devices.
Open AccessPhotocurable Crosslinker from Bio-Based Non-Isocyanate Poly(hydroxyurethane) for Biocompatible Hydrogels
This study explores the synthesis of photocurable non-isocyanate polyhydroxyethylurethanes (BPHUs) derived from renewable sources, designed for biomedical applications and the development towards advanced light curing processes. The following two pathways were developed: an aliphatic route using 1,4-butanediol-derived cyclic carbonates and an aromatic route with resorcinol-based carbonates. Ring-opening polymerization with dodecanediamine produced BPHU intermediates, which were methacrylated to form photoreactive derivatives (aliphatic MAs and aromatic MAs). Comprehensive characterization, including NMR, GPC, and FTIR, confirmed the successful synthesis. The UV curing of these methacrylated compounds yielded hydrogels with swelling properties. Aliphatic BPHUs achieved a gel content of 91.3% and a swelling of 1057%, demonstrating the flexibility and UV stability suitable for adaptable biomedical applications. Conversely, aromatic BPHUs displayed a gel content of 78.1% and a swelling of 3304%, indicating higher rigidity, which is advantageous for load-bearing uses. Cytotoxicity assessments adhering to the DIN EN ISO 10993-5 standard demonstrated non-cytotoxicity, with an >80% cell viability for both variants. This research underscores the potential of green chemistry in crafting biocompatible, versatile BPHUs, paving the way for eco-friendly materials in implantable medical devices.
- Open Access
- 26 October 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (44) , 39772-39781
Green Chemistry for Biomimetic Materials: Synthesis and Electrospinning of High-Molecular-Weight Polycarbonate-Based Nonisocyanate Polyurethanes
Conventional synthesis routes for thermoplastic polyurethanes (TPUs) still require the use of isocyanates and tin-based catalysts, which pose considerable safety and environmental hazards. To reduce both the ecological footprint and human health dangers for nonwoven TPU scaffolds, it is key to establish a green synthesis route, which eliminates the use of these toxic compounds and results in biocompatible TPUs with facile processability. In this study, we developed high-molecular-weight nonisocyanate polyurethanes (NIPUs) through transurethanization of 1,6-hexanedicarbamate with polycarbonate diols (PCDLs). Various molecular weights of PCDL were employed to maximize the molecular weight of NIPUs and consequently facilitate their electrospinnability. The synthesized NIPUs were characterized by nuclear magnetic resonance, Fourier-transform infrared spectroscopy, gel permeation chromatography, and differential scanning calorimetry. The highest achieved molecular weight (M w) was 58,600 g/mol. The NIPUs were consecutively electrospun into fibrous scaffolds with fiber diameters in the submicron range, as shown by scanning electron microscopy (SEM). To assess the suitability of electrospun NIPU mats as a possible biomimetic load-bearing pericardial substitute in cardiac tissue engineering, their cytotoxicity was investigated in vitro using primary human fibroblasts and a human epithelial cell line. The bare NIPU mats did not need further biofunctionalization to enhance cell adhesion, as it was not outperformed by collagen-functionalized NIPU mats and hence showed that the NIPU mats possess a great potential for use in biomimetic scaffolds.
- 26 October 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (44) , 39772-39781
Open AccessGreen Chemistry for Biomimetic Materials: Synthesis and Electrospinning of High-Molecular-Weight Polycarbonate-Based Nonisocyanate Polyurethanes
Conventional synthesis routes for thermoplastic polyurethanes (TPUs) still require the use of isocyanates and tin-based catalysts, which pose considerable safety and environmental hazards. To reduce both the ecological footprint and human health dangers for nonwoven TPU scaffolds, it is key to establish a green synthesis route, which eliminates the use of these toxic compounds and results in biocompatible TPUs with facile processability. In this study, we developed high-molecular-weight nonisocyanate polyurethanes (NIPUs) through transurethanization of 1,6-hexanedicarbamate with polycarbonate diols (PCDLs). Various molecular weights of PCDL were employed to maximize the molecular weight of NIPUs and consequently facilitate their electrospinnability. The synthesized NIPUs were characterized by nuclear magnetic resonance, Fourier-transform infrared spectroscopy, gel permeation chromatography, and differential scanning calorimetry. The highest achieved molecular weight (M w) was 58,600 g/mol. The NIPUs were consecutively electrospun into fibrous scaffolds with fiber diameters in the submicron range, as shown by scanning electron microscopy (SEM). To assess the suitability of electrospun NIPU mats as a possible biomimetic load-bearing pericardial substitute in cardiac tissue engineering, their cytotoxicity was investigated in vitro using primary human fibroblasts and a human epithelial cell line. The bare NIPU mats did not need further biofunctionalization to enhance cell adhesion, as it was not outperformed by collagen-functionalized NIPU mats and hence showed that the NIPU mats possess a great potential for use in biomimetic scaffolds.
- Open Access
Photo-Curing Kinetics of 3D-Printing Photo-Inks Based on Urethane-Acrylates
In this study, photo-curing kinetics for urethane-acrylate-based photo-inks for 3D printing were evaluated using a photo-differential scanning calorimetry analysis. Initially, the photopolymerization kinetics of di- and monofunctional monomers were separately studied at different temperatures (5–85 °C). Later, the photo-curing kinetics and mechanical properties of photo-inks based on different monomer mixtures (40/60–20/80) were evaluated. The results showed that urethane-dimethacrylate (UrDMA) and urethane-acrylate (UrA) had no light absorption in the region of 280–700 nm, making them a proper crosslinker and a reactive diluent, respectively, for the formulation of 3D-printing photo-inks. The kinetics investigations showed a temperature dependency for the photo-curing of UrDMA, where a higher photopolymerization rate (Rp,max: from 5.25 × 10−2 to 8.42 × 10−2 1/s) and double-bound conversion (DBCtotal: from 63.8% to 92.2%) were observed at elevated temperatures (5–85 °C), while the photo-curing of UrA was independent of the temperature (25–85 °C). Enhancing the UrA content from 60% to 80% in the UrDMA/UrA mixtures initially increased and later decreased the photopolymerization rate and conversion, where the mixtures of 30/70 and 25/75 presented the highest values. Meanwhile, increasing the UrA content led to lower glass transition temperatures (Tg) and mechanical strength for the photo-cured samples, where the mixture of 30/70 presented the highest maximum elongation (εmax: 73%).
Open AccessPhoto-Curing Kinetics of 3D-Printing Photo-Inks Based on Urethane-Acrylates
In this study, photo-curing kinetics for urethane-acrylate-based photo-inks for 3D printing were evaluated using a photo-differential scanning calorimetry analysis. Initially, the photopolymerization kinetics of di- and monofunctional monomers were separately studied at different temperatures (5–85 °C). Later, the photo-curing kinetics and mechanical properties of photo-inks based on different monomer mixtures (40/60–20/80) were evaluated. The results showed that urethane-dimethacrylate (UrDMA) and urethane-acrylate (UrA) had no light absorption in the region of 280–700 nm, making them a proper crosslinker and a reactive diluent, respectively, for the formulation of 3D-printing photo-inks. The kinetics investigations showed a temperature dependency for the photo-curing of UrDMA, where a higher photopolymerization rate (Rp,max: from 5.25 × 10−2 to 8.42 × 10−2 1/s) and double-bound conversion (DBCtotal: from 63.8% to 92.2%) were observed at elevated temperatures (5–85 °C), while the photo-curing of UrA was independent of the temperature (25–85 °C). Enhancing the UrA content from 60% to 80% in the UrDMA/UrA mixtures initially increased and later decreased the photopolymerization rate and conversion, where the mixtures of 30/70 and 25/75 presented the highest values. Meanwhile, increasing the UrA content led to lower glass transition temperatures (Tg) and mechanical strength for the photo-cured samples, where the mixture of 30/70 presented the highest maximum elongation (εmax: 73%).
- Open Access
Synthesis and Characterization of Catechol-Containing Polyacrylamides with Adhesive Properties
In this study, a row of four analogous dopamine acryl- and methacrylamide derivatives, namely N-(3,4-dihydroxyphenyethyl) acrylamide, N-(3,4-dihydroxyphenyethyl) meth acrylamide, N-phenethyl methacrylamide, N-(4-hydroxyphenethyl) methacrylamide were synthesized and characterized by 1H-NMR and 13C-NMR, followed by further solvent-based radical polymerization with N-hydroxyethyl acrylamide. All copolymers were characterized by 1H-NMR, dynamic differential calorimetry, and gel permeation chromatography. The dependency of the used comonomer ratios to the molecular mass of the corresponding copolymers has been described. The synthesis of the various polymers serves as a feasibility study and provides important data for a future biometric application in the medical field. We synthesized N-(3,4-dihydroxyphenyethyl) acrylamide copolymer up to 80 mol% by free radical polymerization without using any protecting groups. All polymers show identical perfect adhesive properties by a simple scratch test. Further, the monomers were used as a photo reactive glue formulation to test its adherence to a medical titanium surface sample by tensile shear test.
Open AccessSynthesis and Characterization of Catechol-Containing Polyacrylamides with Adhesive Properties
In this study, a row of four analogous dopamine acryl- and methacrylamide derivatives, namely N-(3,4-dihydroxyphenyethyl) acrylamide, N-(3,4-dihydroxyphenyethyl) meth acrylamide, N-phenethyl methacrylamide, N-(4-hydroxyphenethyl) methacrylamide were synthesized and characterized by 1H-NMR and 13C-NMR, followed by further solvent-based radical polymerization with N-hydroxyethyl acrylamide. All copolymers were characterized by 1H-NMR, dynamic differential calorimetry, and gel permeation chromatography. The dependency of the used comonomer ratios to the molecular mass of the corresponding copolymers has been described. The synthesis of the various polymers serves as a feasibility study and provides important data for a future biometric application in the medical field. We synthesized N-(3,4-dihydroxyphenyethyl) acrylamide copolymer up to 80 mol% by free radical polymerization without using any protecting groups. All polymers show identical perfect adhesive properties by a simple scratch test. Further, the monomers were used as a photo reactive glue formulation to test its adherence to a medical titanium surface sample by tensile shear test.
- Open Access
- 15 December 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (72) , 44103-44110
Developing non-isocyanate urethane-methacrylate photo-monomers for 3D printing application
Urethane-methacrylate photo-monomers were prepared via a non-isocyanate route for the 3D printing application. The monomers were synthesized through reacting aliphatic amines, i.e. 1,6-hexanediamine, 1,4-butanediol bis(3-aminopropyl) ether, or n-butylamine, with cyclic carbonates, i.e. ethylene carbonate or propylene carbonate, followed by the methacrylation of the generated hydroxylurethanes. The effects of the chemical structure of monomers on their photo-reactivity and physicomechanical properties of the cured samples were studied. Propylene carbonate generated side methyl groups within the urethane block, which significantly limited the crystallization of the monomers resulting in high photo-reactivity (Rp,max = 6.59 × 10−2 s−1) and conversion (DBCtotal = 85%). The ether bonds of 1,4-butanediol bis(3-aminopropyl) ether decreased the intermolecular hydrogen bonding between urethane blocks, which not only improved the photo-reactivity (Rp,max = 8.18 × 10−2 s−1) and conversion (DBCtotal = 86%) of the monomer but led to a high crosslinking density (νc = 5140 mol m−3) and more flexibility for the cured sample. An ink was developed based on the monomers and successfully 3D printed on a digital light processing machine. In the absence of toxic isocyanates and tin compounds, the non-isocyanate route can be employed to develop urethane-methacrylates with desirable photo-reactivity and physicomechanical properties as good candidates to formulate inks for 3D printing of biomedical materials.
- 15 December 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (72) , 44103-44110
Open AccessDeveloping non-isocyanate urethane-methacrylate photo-monomers for 3D printing application
Urethane-methacrylate photo-monomers were prepared via a non-isocyanate route for the 3D printing application. The monomers were synthesized through reacting aliphatic amines, i.e. 1,6-hexanediamine, 1,4-butanediol bis(3-aminopropyl) ether, or n-butylamine, with cyclic carbonates, i.e. ethylene carbonate or propylene carbonate, followed by the methacrylation of the generated hydroxylurethanes. The effects of the chemical structure of monomers on their photo-reactivity and physicomechanical properties of the cured samples were studied. Propylene carbonate generated side methyl groups within the urethane block, which significantly limited the crystallization of the monomers resulting in high photo-reactivity (Rp,max = 6.59 × 10−2 s−1) and conversion (DBCtotal = 85%). The ether bonds of 1,4-butanediol bis(3-aminopropyl) ether decreased the intermolecular hydrogen bonding between urethane blocks, which not only improved the photo-reactivity (Rp,max = 8.18 × 10−2 s−1) and conversion (DBCtotal = 86%) of the monomer but led to a high crosslinking density (νc = 5140 mol m−3) and more flexibility for the cured sample. An ink was developed based on the monomers and successfully 3D printed on a digital light processing machine. In the absence of toxic isocyanates and tin compounds, the non-isocyanate route can be employed to develop urethane-methacrylates with desirable photo-reactivity and physicomechanical properties as good candidates to formulate inks for 3D printing of biomedical materials.
- 1 September 2018
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 357, 30-39
Bio-based thermosetting epoxy foam: Tannic acid valorization toward dye-decontaminating and thermo-protecting applications
- 1 September 2018
- Published by Elsevier in Journal of Hazardous Materials
- Vol. 357, 30-39
Bio-based thermosetting epoxy foam: Tannic acid valorization toward dye-decontaminating and thermo-protecting applications
- Open Access
- 31 July 2018
- Published by AccScience Publishing in International Journal of Bioprinting
- Vol. 4 (2)
Optimized vascular network by stereolithography for tissue engineered skin
This paper demonstrates the essential and efficient methods to design, and fabricate optimal vascular network for tissue engineering structures based on their physiological conditions. Comprehensive physiological requirements in both micro and macro scales were considered in developing the optimisation design for complex vascular vessels. The optimised design was then manufactured by stereolithography process using materials that are biocompatible, elastic and surface bio-coatable. The materials are self-developed photocurable resin consist of BPA-ethoxylated-diacrylate, lauryl acrylate and isobornylacrylate with Irgacure® 184, the photoinitiator. The optimised vascular vessel offers many advantages: 1) it provides the maximum nutrient supply; 2) it minimises the recirculation areas and 3) it allows the wall shear stress on the vessel in a healthy range. The stereolithography manufactured vascular vessels were then embedded in the hydrogel seeded with cells. The results of in vitro studies show that the optimised vascular network has the lowest cell death rate compared with a pure hydrogel scaffold and a hydrogel scaffold embedded within a single tube in day seven. Consequently, these design and manufacture routes were shown to be viable for exploring and developing a high range complex and specialised artificial vascular networks.
- 31 July 2018
- Published by AccScience Publishing in International Journal of Bioprinting
- Vol. 4 (2)
Open AccessOptimized vascular network by stereolithography for tissue engineered skin
This paper demonstrates the essential and efficient methods to design, and fabricate optimal vascular network for tissue engineering structures based on their physiological conditions. Comprehensive physiological requirements in both micro and macro scales were considered in developing the optimisation design for complex vascular vessels. The optimised design was then manufactured by stereolithography process using materials that are biocompatible, elastic and surface bio-coatable. The materials are self-developed photocurable resin consist of BPA-ethoxylated-diacrylate, lauryl acrylate and isobornylacrylate with Irgacure® 184, the photoinitiator. The optimised vascular vessel offers many advantages: 1) it provides the maximum nutrient supply; 2) it minimises the recirculation areas and 3) it allows the wall shear stress on the vessel in a healthy range. The stereolithography manufactured vascular vessels were then embedded in the hydrogel seeded with cells. The results of in vitro studies show that the optimised vascular network has the lowest cell death rate compared with a pure hydrogel scaffold and a hydrogel scaffold embedded within a single tube in day seven. Consequently, these design and manufacture routes were shown to be viable for exploring and developing a high range complex and specialised artificial vascular networks.
- 1 June 2018
- Published by Elsevier in Thermochimica Acta
- Vol. 664, 64-72
Tannic acid derived non-isocyanate polyurethane networks: Synthesis, curing kinetics, antioxidizing activity and cell viability
- 1 June 2018
- Published by Elsevier in Thermochimica Acta
- Vol. 664, 64-72
Tannic acid derived non-isocyanate polyurethane networks: Synthesis, curing kinetics, antioxidizing activity and cell viability