Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Jamshid Malekmohammadi Nouri has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Turbulent flow development within the discharge cavity of a screw compressor

    by Jamshid M Nouri, Diego Guerrato, Nikola Stosic, Youyou Yan

    Spatial flow field velocities within the discharge cavity of an optical screw compressor have been measured using LDV and PIV techniques. Angle-resolved velocities were obtained over a time window of 1° at a speed of 1000 rpm, pressure ratio of 1 and temperature of 55°C. Comparison between the LDV and PIV results showed very good agreement and provided a good level of confidence in the presented data. Overall, the flow field results revealed the presence of a complex, turbulent, 3D and vortical flow structure within the discharge cavity. LDV measurements at the exit of the discharge port showed that the inflow into the cavity has two distinct flow features that includes undulated velocity profiles with high gradient during the opening of the port, and uniform jet-like flows during the rest of the time. The energy necessary to create that jet-like flow was from the built-in pressure in the rotors. Turbulence fluctuations were high and followed the mean flow variations with values up to 35% of the mean values during the undulating flow. PIV spatial mean flow measurements showed a uniform axial flow close to bottom of cavity that has been transformed to a stable solid body vortex at the top of the cavity. These measurements within the discharge cavity are made for the first time and they are unique and in great detail that can be used for validation of CFD codes and optimisation of compressors to improve their efficiency for different system applications. Graphical [ ]


  • Open Access

    Predictions of Vortex Flow in a Diesel Multi-Hole Injector Using the RANS Modelling Approach

    by Aishvarya Kumar, Jamshid Nouri, Ali Ghobadian

    The occurrence of vortices in the sac volume of automotive multi-hole fuel injectors plays an important role in the development of vortex cavitation, which directly influences the flow structure and emerging sprays that, in turn, influence the engine performance and emissions. In this study, the RANS-based turbulence modelling approach was used to predict the internal flow in a vertical axis-symmetrical multi-hole (6) diesel fuel injector under non-cavitating conditions. The project aimed to predict the aforementioned vortical structures accurately at two different needle lifts in order to form a correct opinion about their occurrence. The accuracy of the simulations was assessed by comparing the predicted mean axial velocity and RMS velocity of LDV measurements, which showed good agreement. The flow field analysis predicted a complex, 3D, vortical flow structure with the presence of different types of vortices in the sac volume and the nozzle hole. Two main types of vortex were detected: the “hole-to-hole” connecting vortex, and double “counter-rotating” vortices emerging from the needle wall and entering the injector hole facing it. Different flow patterns in the rotational direction of the “hole-to-hole” vortices have been observed at the low needle lift (anticlockwise) and full needle lift (clockwise), due to their different flow passages in the sac, causing a much higher momentum inflow at the lower lift with its much narrower flow passage.


  • Open Access

    Cavitation between cylinder-liner and piston-ring in a new designed optical IC engine

    by Jamshid Malekmohammadi Nouri, Ioannis Vasilakos, Youyou Yan

    A new engine block with optical access has been designed and manufactured capable of running up to 3000 r/min with the same specification as the unmodified engine. The optical window allowed access to the full length of the liner over a width of 25 mm to investigate the lubricant flow and cavitation at contact point between the rings and cylinder-liner. In addition, it allowed good access into the combustion chamber to allow charged flow, spray and combustion visualisation and measurements using different optical methods. New custom engine management system with build in LabView allowed for the precise full control of the engine. The design of the new optical engine was a great success in producing high quality images of lubricant flow, cavitation formation and development at contact point at different engine speeds ranging from 208 to 3000 r/min and lubricant temperatures (30°C–70°C) using a high-speed camera. The results under motorised operation confirmed that there was no cavitation at contact points during the intake/exhaust strokes due to low in-cylinder presure, while during compression/expansion strokes, with high in-cylinder pressure, considerable cavities were observed, in particular, during the compression stroke. Lubricant temperatures had the effect of promoting cavities both in their intensity and covered ring area up to 50°C as expected. Beyond that, although the cavitation intensity increases further with temperature, its area reduces due to possible collapse of the cavitating bubbles at higher temperature. The change of engine speed from 208 to 800 r/min increased cavitating area considerably by 52% of the ring area and was further increased by 19% at 1000 r/min. After that, the results showed very small increase in cavitation area (1.3% at 2000 r/min) with similar intensity and distribution across the ring.


  • Open Access

    Numerical simulation and experimental validation of cavitating flow in a multi-hole diesel fuel injector

    by Aishvarya Kumar, Ali Ghobadian, Jamshid Nouri

    This study assesses the predictive capability of the ZGB (Zwart-Gerber-Belamri) cavitation model with the RANS (Reynolds Averaged Navier-Stokes), the realizable k-epsilon turbulence model, and compressibility of gas/liquid models for cavitation simulation in a multi-hole fuel injector at different cavitation numbers (CN) for diesel and biodiesel fuels. The prediction results were assessed quantitatively by comparison of predicted velocity profiles with those of measured LDV (Laser Doppler Velocimetry) data. Subsequently, predictions were assessed qualitatively by visual comparison of the predicted void fraction with experimental CCD (Charged Couple Device) recorded images. Both comparisons showed that the model could predict fluid behavior in such a condition with a high level of confidence. Additionally, flow field analysis of numerical results showed the formation of vortices in the injector sac volume. The analysis showed two main types of vortex structures formed. The first kind appeared connecting two adjacent holes and is known as “hole-to-hole” connecting vortices. The second type structure appeared as double “counter-rotating” vortices emerging from the needle wall and entering the injector hole facing it. The use of RANS proved to save significant computational cost and time in predicting the cavitating flow with good accuracy.


  • Open Access

    Scale-Resolving Simulation of a Propane-Fuelled Industrial Gas Turbine Combustor Using Finite-Rate Tabulated Chemistry

    by Kai Zhang, Ali Ghobadian, Jamshid M. Nouri

    The scale-resolving simulation of a practical gas turbine combustor is performed using a partially premixed finite-rate chemistry combustion model. The combustion model assumes finite-rate chemistry by limiting the chemical reaction rate with flame speed. A comparison of the numerical results with the experimental temperature and species mole fraction clearly showed the superiority of the shear stress transport, K-omega, scale adaptive turbulence model (SSTKWSAS). The model outperforms large eddy simulation (LES) in the primary region of the combustor, probably for two reasons. First, the lower amount of mesh employed in the simulation for the industrial-size combustor does not fit the LES’s explicit mesh size dependency requirement, while it is sufficient for the SSTKWSAS simulation. Second, coupling the finite-rate chemistry method with the SSTKWSAS model provides a more reasonable rate of chemical reaction than that predicted by the fast chemistry method used in LES simulation. Other than comparing with the LES data available in the literature, the SSTKWSAS-predicted result is also compared comprehensively with that obtained from the model based on the unsteady Reynolds-averaged Navier–Stokes (URANS) simulation approach. The superiority of the SSTKWSAS model in resolving large eddies is highlighted. Overall, the present study emphasizes the effectiveness and efficiency of coupling a partially premixed combustion model with a scale-resolving simulation method in predicting a swirl-stabilized, multi-jets turbulent flame in a practical, complex gas turbine combustor configuration.


  • Open Access

    Turbulent Flow Measurements near the Discharge Port of a Screw Compressor

    by J. M. Nouri, D. Guerrato, N. Stosic

    Mean flow and turbulence characteristics have been measured within the male and female rotors close to the discharge port of a double screw compressor at different radial positions, two axial positions from the exit port, Hp, and two radial planes, αp. Cycle-resolved axial and tangential mean flow measurements and their corresponding turbulent velocity fluctuations were made over a time window of 1° using a laser Doppler velocimetry, LDV, system. Measurements were performed through two transparent windows near the inlet of the discharge port inside the male and female working chambers. The results revealed a highly complex 3-D flow within the male and female working chambers, in particular, near the discharge port with two distinct flow zones 1 and 2 before and after the opening of the port, respectively. The flow in zone 1 was controlled by the rotor motion while in zone 2 was greatly influenced by the discharge process. In zone 2, both components of mean velocities were subjected to a sudden increase in velocity forming strong axial and tangential jet flows due to rapid change in pressure across the port as the flow is exposed into the discharge port. It was found that the flow structures have been affected considerably by the position of the discharge port, radial planes and radial positions. Axial and tangential RMS velocity distributions within both rotors were found to be relatively high and less affected by the flow changes of zones 1 and 2 with almost uniform distribution. The measured magnitudes of axial and tangential RMS velocities suggest it would be reasonable to assume the local turbulence to be isotropic for the modelling purposes. To authors’ knowledge, the results are unique, original and in great details not only to describe the flow structure, but also, they can be used in CFD codes to establish a reliable model of the flow and pressure distribution within twin screw machines.


  • Open Access

    Effect of Viscosity and Speed on Oil Cavitation Development in a Single Piston-Ring Lubricant Assembly

    by Jamshid M. Nouri, Ioannis Vasilakos, Youyou Yan, Constantino-Carlos Reyes-Aldasoro

    A high-speed camera has been used to produce unique time-resolved images of high quality to describe the dynamics of the lubricant flow and cavitation characteristics in a sliding optical liner over a fixed single piston-ring lubricant assembly for three lubricants with different viscosities to establish their impact on cavitation formation and development. The images were obtained at two cranking speeds (or liner sliding velocity) of 300 rpm (0–0.36 m/s) and 600 rpm (0–0.72 m/s), at a lubricant temperature of 70 °C and a supply lubricant rate of 0.05 L/min. A special MATLAB programme has been developed to analyse the cavitation characteristics quantitatively. The dynamic process of cavities initiation was demonstrated by time-resolved images from fern cavity formation to fissure cavities and then their development to the sheet and strings cavities at a liner sliding velocity of around 0.17 m/s. The results for both up- and down-stroke motions showed that the cavities reach their fully developed state downstream of the contact point when the liner velocity reaches its highest velocity and that they start to collapse around TDC and BDC when the liner comes to rest. Within the measured range, viscosity had a great influence on length of cavities so that a decrease in viscosity (from Lubricant A to C) caused a reduction in length of cavities of up to 35% for Lubricant C. On the other hand, an increase in speed, from 300 rpm to 600 rpm, have increased the number of string cavities and also increased the length of cavities due to thicker oil film thickness with the higher speed. Overall, the agreement between the processed data by MATLAB and visualisation measurements were good, but further thresholds refinement is required to improve the accuracy.


  • Open Access

    Mechanical properties of graphene oxide reinforced aluminium matrix composites

    by Bhagya Lakshmi Dasari, Muhammad Morshed, Jamshid M. Nouri, Dermot Brabazon, Sumsun Naher


  • Open Access

    Graphene and derivatives – Synthesis techniques, properties and their energy applications

    by Bhagya Lakshmi Dasari, Jamshid M. Nouri, Dermot Brabazon, Sumsun Naher


  • Parametric study for graphene reinforced aluminum matrix composites production using Box Behnken design

    by Bhagya Lakshmi Dasari, Jamshid M. Nouri, Dermot Brabazon, Sumsun Naher

    The production of graphene reinforced aluminum matrix composite through powder metallurgical route requires optimization of process parameters to obtain better performance characteristics. One of the advanced method available for statistical analysis of parameters is Response Surface Methodology (RSM). The statistical analysis was carried out with three parameters, weight percentage of graphene reinforcement Wg (0.05%, 0.1% and 0.2%), stirring time ST(1h, 2h and 3h) and compaction pressure Pc(16T, 17T and 19T) while sintering temperature T kept constant. The performance of the Box Behnken design was analyzed and optimized using Design Expert software for the effective production of composites. From the results obtained from the analysis, the best set of parameters were considered for the future production of composites.