Farzaneh Tahmoorian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Farzaneh Tahmoorian has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Bijan Samali
Western Sydney University
6 shared publications - Farshad Sanati
Mechanical Engineering Faculty, Mashhad University, Mashhad 9177948974, Iran
2 shared publications John Yeaman
Professor, Faculty of Science, Health, Education, and Engineering, Univ. of the Sunshine Coast, Sippy Downs, QLD 4556, Australia
2 shared publications- John Yeaman
Faculty of Science, Health, Education and Engineering, University of Sunshine Coast, Sippy Downs, Queensland 4556, Australia
2 shared publications - Saeed Nemati
Centre for Infrastructure Engineering, Western Sydney University, Kingswood 2747, Australia
2 shared publications - Asmaa Al-Taie
Institute for Sustainable Industries and Liveable Cities, Victoria University
1 shared publication
Latest Publications
- Open Access
- 6 October 2026
- Published by Springer Nature in International Journal of Pavement Research and Technology
- p. 1-25
Experimentally Driven 3D Viscoelastic Modelling and Validation of Flexible Pavement with Waste Cooking Oil and Nano-Silica Modified Asphalt Under Stationary and Quasi-Static Loads
This study develops a three-dimensional finite element model of a flexible pavement containing C320 asphalt modified with waste cooking oil (WCO) and nano-silica (NS). A formulation with 4.0% treated WCO and 2.0% NS was selected through binder screening. Across 24 temperature-frequency conditions, dynamic modulus decreased from 8.60 to 0.56 GPa and phase angle increased from 10.8° to 38.5°. MATLAB R2025a was used to fit the master curve, shift factors and five-term Prony-series parameters. The fit gave R², RMSE, and MAPE values of 0.998, 0.100 GPa, and 3.42%, respectively, for dynamic modulus and 0.994, 0.610°, and 2.58%, respectively, for phase angle. Abaqus/Standard was used to develop the pavement model. Effective asphalt and support-layer stiffnesses were calibrated against Austroads stationary single-axle single-tyre (SAST) pavement-box measurements at 20 °C, giving a calibration MAPE of about 1.40%. Independent validation used a separate stationary single-axle dual-tyre (SADT) pavement-box dataset at 20 °C that was not included during calibration, with no further parameter adjustment. Model predictions of 0.341 mm, 101 µε and 151 µε were compared with measured values of 0.372 ± 0.020 mm, 92 ± 6 µε and 166 ± 10 µε, giving individual errors of 8.33%, 9.78% and 9.04% and a validation MAPE of 9.05%. The validated model was then used to compare stationary and quasi-static stepped SAST and SADT loading. When peak finite element outputs were used for this comparison, SADT gave lower normalised peak responses than SAST.
- 6 October 2026
- Published by Springer Nature in International Journal of Pavement Research and Technology
- p. 1-25
Open AccessExperimentally Driven 3D Viscoelastic Modelling and Validation of Flexible Pavement with Waste Cooking Oil and Nano-Silica Modified Asphalt Under Stationary and Quasi-Static Loads
This study develops a three-dimensional finite element model of a flexible pavement containing C320 asphalt modified with waste cooking oil (WCO) and nano-silica (NS). A formulation with 4.0% treated WCO and 2.0% NS was selected through binder screening. Across 24 temperature-frequency conditions, dynamic modulus decreased from 8.60 to 0.56 GPa and phase angle increased from 10.8° to 38.5°. MATLAB R2025a was used to fit the master curve, shift factors and five-term Prony-series parameters. The fit gave R², RMSE, and MAPE values of 0.998, 0.100 GPa, and 3.42%, respectively, for dynamic modulus and 0.994, 0.610°, and 2.58%, respectively, for phase angle. Abaqus/Standard was used to develop the pavement model. Effective asphalt and support-layer stiffnesses were calibrated against Austroads stationary single-axle single-tyre (SAST) pavement-box measurements at 20 °C, giving a calibration MAPE of about 1.40%. Independent validation used a separate stationary single-axle dual-tyre (SADT) pavement-box dataset at 20 °C that was not included during calibration, with no further parameter adjustment. Model predictions of 0.341 mm, 101 µε and 151 µε were compared with measured values of 0.372 ± 0.020 mm, 92 ± 6 µε and 166 ± 10 µε, giving individual errors of 8.33%, 9.78% and 9.04% and a validation MAPE of 9.05%. The validated model was then used to compare stationary and quasi-static stepped SAST and SADT loading. When peak finite element outputs were used for this comparison, SADT gave lower normalised peak responses than SAST.
- 27 April 2026
- Published by Raw Data Library
Application of waste materials in asphalt mixtures
Road networks are increasingly expanding all over the world. Over the past decades, the buoyant economy, growing population and increasing freight volumes have created high demand for new road pavements as well as the maintenance of current road networks. The construction and maintenance of the road pavements require large amounts of aggregates. Due to considerable usage of various natural aggregates for constructing roads, these materials have started to deplete gradually. At the same time, the generation rate of solid waste in the society is increasing with the increase of population, technological development, and changes in the life style of people. The management of solid wastes has become an acute problem due to enhanced economic activities and rapid urbanization. Moreover, according to World Commission on Environment and Development (1987), sustainable development is defined as the development that meets the needs of the present without compromising the ability of future generations to meet their own needs. Therefore, referring to the importance of the sustainability and all the above mentioned issues, the utilization of recycled materials and waste materials in the manufacture of new asphalt mixtures is addressed in this research, in order to follow the sustainability concept. Using waste materials in asphalt mixtures conserves natural aggregates, reduces the impact on landfills, decreases energy consumption, can provide cost savings, and generally results in significant economic and environmental benefits. In spite of the benefits mentioned above, designing asphalt mixtures containing waste materials can be challenging and complex. In this regard, it is necessary to review a wide variety of engineering and geotechnical considerations for asphalt mixture design, as the application of wastes should not influence the structural and functional aspects of the pavements. Among various factors, which would be considered in designing an asphalt mix, permanent deformation, and stress/strain characteristics are the most important factors from the perspective of structural and geotechnical stability. Evaluation of asphalt mixtures in terms of these engineering properties is necessary as they define the structural performance and strength of an asphalt pavement. In fact, these properties influence the ability of the mix in withstanding the destructive effects of traffic and environment. In light of this, many researchers have studied the behaviour of asphalt mixtures containing waste materials through different tests and approaches to predict the performance of the asphalt surface layer under traffic load and environmental conditions. Today, there are many published reports about the application of various waste materials in construction of different layers of pavements including asphalt surface layer. The research studies have been conducted from simple and primary tests to the advanced laboratory investigations, field tests, and constitutive modelling of asphalt surface layer. Due to the wide range of materials that fit into the definition of pavement, this proposed research does not intend to cover the investigation of the application of all types of materials available. Instead, it focuses on the assessment of the utilization of some of the waste materials including Recycled Construction Aggregate (RCA), Glass, plastic, and rubber in Dense Graded Asphalt (DGA) mixture, and it aims to propose a mixture with proper response to traffic loads and environmental conditions as well as appropriate resistance to rutting, cracking, and weathering. In this report, a critical and comprehensive literature review about the performance of the asphalt mixture incorporating selected waste materials is provided. Moreover, this report includes a brief description of the relevant tests commonly specified to provide confidence of material suitability for the intended application as well as the results of these tests. Based on these tests, it is concluded that these waste materials have serious shortcomings in accounting for the asphalt mixtures components. They are also unable to account for designing asphalt mixture individually, and therefore, it is required that combination of some waste materials in certain percentages be considered in designing the asphalt mixture. One of the goals of the proposed research is to determine the optimum percentage of RCA and glass in the mixture, and also to investigate the influence of the application of rubber and plastic in binder characteristics. This will be done through a series of preliminary and primary tests to evaluate the properties of individual components of asphalt mixtures and the volumetric properties of the mixture. The information and data collected from these tests will be used to select the adequate samples for further assessment through advanced tests such as resilient modulus test. Since the variability in the behaviour of RCA used in different construction.
- 27 April 2026
- Published by Raw Data Library
Application of waste materials in asphalt mixtures
Road networks are increasingly expanding all over the world. Over the past decades, the buoyant economy, growing population and increasing freight volumes have created high demand for new road pavements as well as the maintenance of current road networks. The construction and maintenance of the road pavements require large amounts of aggregates. Due to considerable usage of various natural aggregates for constructing roads, these materials have started to deplete gradually. At the same time, the generation rate of solid waste in the society is increasing with the increase of population, technological development, and changes in the life style of people. The management of solid wastes has become an acute problem due to enhanced economic activities and rapid urbanization. Moreover, according to World Commission on Environment and Development (1987), sustainable development is defined as the development that meets the needs of the present without compromising the ability of future generations to meet their own needs. Therefore, referring to the importance of the sustainability and all the above mentioned issues, the utilization of recycled materials and waste materials in the manufacture of new asphalt mixtures is addressed in this research, in order to follow the sustainability concept. Using waste materials in asphalt mixtures conserves natural aggregates, reduces the impact on landfills, decreases energy consumption, can provide cost savings, and generally results in significant economic and environmental benefits. In spite of the benefits mentioned above, designing asphalt mixtures containing waste materials can be challenging and complex. In this regard, it is necessary to review a wide variety of engineering and geotechnical considerations for asphalt mixture design, as the application of wastes should not influence the structural and functional aspects of the pavements. Among various factors, which would be considered in designing an asphalt mix, permanent deformation, and stress/strain characteristics are the most important factors from the perspective of structural and geotechnical stability. Evaluation of asphalt mixtures in terms of these engineering properties is necessary as they define the structural performance and strength of an asphalt pavement. In fact, these properties influence the ability of the mix in withstanding the destructive effects of traffic and environment. In light of this, many researchers have studied the behaviour of asphalt mixtures containing waste materials through different tests and approaches to predict the performance of the asphalt surface layer under traffic load and environmental conditions. Today, there are many published reports about the application of various waste materials in construction of different layers of pavements including asphalt surface layer. The research studies have been conducted from simple and primary tests to the advanced laboratory investigations, field tests, and constitutive modelling of asphalt surface layer. Due to the wide range of materials that fit into the definition of pavement, this proposed research does not intend to cover the investigation of the application of all types of materials available. Instead, it focuses on the assessment of the utilization of some of the waste materials including Recycled Construction Aggregate (RCA), Glass, plastic, and rubber in Dense Graded Asphalt (DGA) mixture, and it aims to propose a mixture with proper response to traffic loads and environmental conditions as well as appropriate resistance to rutting, cracking, and weathering. In this report, a critical and comprehensive literature review about the performance of the asphalt mixture incorporating selected waste materials is provided. Moreover, this report includes a brief description of the relevant tests commonly specified to provide confidence of material suitability for the intended application as well as the results of these tests. Based on these tests, it is concluded that these waste materials have serious shortcomings in accounting for the asphalt mixtures components. They are also unable to account for designing asphalt mixture individually, and therefore, it is required that combination of some waste materials in certain percentages be considered in designing the asphalt mixture. One of the goals of the proposed research is to determine the optimum percentage of RCA and glass in the mixture, and also to investigate the influence of the application of rubber and plastic in binder characteristics. This will be done through a series of preliminary and primary tests to evaluate the properties of individual components of asphalt mixtures and the volumetric properties of the mixture. The information and data collected from these tests will be used to select the adequate samples for further assessment through advanced tests such as resilient modulus test. Since the variability in the behaviour of RCA used in different construction.
- 1 January 2025
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 62, 1-26
Pavement performance over deep trenches backfilled with recycled aggregates under different compaction efforts
Insufficient understanding of the stress–strain behavior of pavements built over backfilled trenches, particularly with recycled aggregates, often leads to overdesign or overcompaction, raising costs and project delays. This research investigates how compaction levels during backfilling impact the pavement performance over these trenches. Various recycled material mixtures, both unbound and cement-treated, are compared with conventional crushed rock. Investigations included repeated load triaxial (RLT) tests, microstructural analysis with scanning electron microscopy, environmental assessments, and modeling with FlexPAVE™, a pavement response and performance analysis software. RLT test results were incorporated into the FlexPAVE™ models by utilizing established constitutive resilient modulus models. Stress–strain responses of pavements over recycled aggregate backfill, compacted with standard and modified Proctor efforts, were compared with those over crushed rock and natural clay subgrades. Outcomes revealed that the standard compaction energy was sufficient for the desired performance. Fatigue and rutting strains with recycled mixtures closely resembled those with crushed rock, making them viable green alternatives. Pavements over backfilled trenches exhibited 1.5 and 1.8 times longer fatigue and rutting lives, respectively, than those over natural clay subgrades.
- 1 January 2025
- Published by Canadian Science Publishing in Canadian Geotechnical Journal
- Vol. 62, 1-26
Pavement performance over deep trenches backfilled with recycled aggregates under different compaction efforts
Insufficient understanding of the stress–strain behavior of pavements built over backfilled trenches, particularly with recycled aggregates, often leads to overdesign or overcompaction, raising costs and project delays. This research investigates how compaction levels during backfilling impact the pavement performance over these trenches. Various recycled material mixtures, both unbound and cement-treated, are compared with conventional crushed rock. Investigations included repeated load triaxial (RLT) tests, microstructural analysis with scanning electron microscopy, environmental assessments, and modeling with FlexPAVE™, a pavement response and performance analysis software. RLT test results were incorporated into the FlexPAVE™ models by utilizing established constitutive resilient modulus models. Stress–strain responses of pavements over recycled aggregate backfill, compacted with standard and modified Proctor efforts, were compared with those over crushed rock and natural clay subgrades. Outcomes revealed that the standard compaction energy was sufficient for the desired performance. Fatigue and rutting strains with recycled mixtures closely resembled those with crushed rock, making them viable green alternatives. Pavements over backfilled trenches exhibited 1.5 and 1.8 times longer fatigue and rutting lives, respectively, than those over natural clay subgrades.
- Open Access
- 15 September 2023
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 18 (2) , 444-457
Improving Gravel Material Specifications for Unpaved Roads: Australian Case Study
Gravel surfacing is a cost-effective approach for constructing roads in sparsely populated regions. However, maintaining the shape and usability of gravel roads requires regular upkeep to ensure road user safety. This study focuses on the significant gravel material specifications for wearing courses and highlights the findings of the Department of Transport and Main Roads (TMR) in Australia regarding the crucial role of material specifications in road maintenance routines. The Goondiwindi area in Queensland, featuring approximately 2000 km of gravel roads, serves as a case study for investigating the viability of granular stabilization techniques in enhancing re-sheeting materials for this network. In this research, gravel samples from ten gravel pits in the region were characterized through a range of tests, including particle-size distribution, Atterberg limit, California bearing ratio (CBR), and capillary rise. These laboratory investigations facilitated the development of a desktop analysis tool that predicts the engineering properties of gravel blends obtained from different pits. The validity of this analysis tool was assessed by comparing its results with comprehensive laboratory investigations of gravel samples and their blends. The verification process demonstrated that the results obtained from the desktop analysis tool aligned well with the test results. The study concludes that the analysis tool can effectively identify suitable gravel blends that meet target specifications, provided that the shrinkage product and CBR values of the parent pits are acceptable. The findings of this research can enhance confidence in designing gravel blends for wearing courses based on the properties of individual gravel pits, eliminating the need for additional testing on the gravel blends, and thus reducing costs.
- 15 September 2023
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 18 (2) , 444-457
Open AccessImproving Gravel Material Specifications for Unpaved Roads: Australian Case Study
Gravel surfacing is a cost-effective approach for constructing roads in sparsely populated regions. However, maintaining the shape and usability of gravel roads requires regular upkeep to ensure road user safety. This study focuses on the significant gravel material specifications for wearing courses and highlights the findings of the Department of Transport and Main Roads (TMR) in Australia regarding the crucial role of material specifications in road maintenance routines. The Goondiwindi area in Queensland, featuring approximately 2000 km of gravel roads, serves as a case study for investigating the viability of granular stabilization techniques in enhancing re-sheeting materials for this network. In this research, gravel samples from ten gravel pits in the region were characterized through a range of tests, including particle-size distribution, Atterberg limit, California bearing ratio (CBR), and capillary rise. These laboratory investigations facilitated the development of a desktop analysis tool that predicts the engineering properties of gravel blends obtained from different pits. The validity of this analysis tool was assessed by comparing its results with comprehensive laboratory investigations of gravel samples and their blends. The verification process demonstrated that the results obtained from the desktop analysis tool aligned well with the test results. The study concludes that the analysis tool can effectively identify suitable gravel blends that meet target specifications, provided that the shrinkage product and CBR values of the parent pits are acceptable. The findings of this research can enhance confidence in designing gravel blends for wearing courses based on the properties of individual gravel pits, eliminating the need for additional testing on the gravel blends, and thus reducing costs.
- 1 March 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 149 (1) , 04023001
Performance of Hot-Mix Asphalt and Modified Binders Containing Polyethylene
The demand for high-performance asphalt pavements has been increasing in recent years due to increased traffic volume, automobile size and weight, and rising temperatures due to climate change. It is necessary to modify the bitumen to achieve long-life high-performance pavements in many cases. Consequently, polymers obtained from plastic wastes emerged as a modifier to enhance the bitumen properties. Polymers offer a number of advantages. Polymers such as polyethylene (PE) or polypropylene (PP) offer a number of advantages when used as binder modifier. Using PE or PP in infrastructure projects can be an innovative method to reduce the environmental damage of these nonbiodegradable wastes and the high cost of recycling these wastes. Therefore, this paper extensively investigates the experimental studies carried out by many researchers to evaluate polymer-modified binders’ properties as an alternative for pure bitumen in asphalt mixtures under different percentages and production processes. The main goal is to establish a better understanding of the engineering properties of polyethylene-modified asphalt mixtures and ultimately argue that waste polyethylene has a viable use as a modifier for asphalt binders.
- 1 March 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 149 (1) , 04023001
Performance of Hot-Mix Asphalt and Modified Binders Containing Polyethylene
The demand for high-performance asphalt pavements has been increasing in recent years due to increased traffic volume, automobile size and weight, and rising temperatures due to climate change. It is necessary to modify the bitumen to achieve long-life high-performance pavements in many cases. Consequently, polymers obtained from plastic wastes emerged as a modifier to enhance the bitumen properties. Polymers offer a number of advantages. Polymers such as polyethylene (PE) or polypropylene (PP) offer a number of advantages when used as binder modifier. Using PE or PP in infrastructure projects can be an innovative method to reduce the environmental damage of these nonbiodegradable wastes and the high cost of recycling these wastes. Therefore, this paper extensively investigates the experimental studies carried out by many researchers to evaluate polymer-modified binders’ properties as an alternative for pure bitumen in asphalt mixtures under different percentages and production processes. The main goal is to establish a better understanding of the engineering properties of polyethylene-modified asphalt mixtures and ultimately argue that waste polyethylene has a viable use as a modifier for asphalt binders.
- 1 January 2022
- Published by Civilicom
- Vol. 1 (1) , 1-11
A New Framework for Determining the Gradation of Asphalt Mixtures
Strength and rutting resistance as well as durability are the main quality measures for any asphalt mix. While the strength and resistance of the asphalt mixture to permanent deformation are controlled by the aggregate interlock and aggregate packing, the durability of asphalt mixture depends on adequate volumetric characteristics and film thickness of asphalt mixture. Accordingly, providing an adequate interlock between aggregates and the aggregate packing is of high importance in designing a new asphalt mixture in order to produce desirable volumetric characteristics in asphalt mixture. A new framework for asphalt mixture gradation has been developed and designed following an intensive review of the various currently used approaches. The new framework considers all the controlling factors in the aggregate gradation design for optimum gradation of the asphalt mixtures. Satisfactory interlocking between aggregate particles, proper skeleton within the asphalt mixture, and acceptable volumetric properties are the main parameters to be considered for optimum gradation design for asphalt mix. The framework provides a systematic approach for the gradation process starting from the concentration at different sieves to finally account for the 𝐹𝐴 ≤ 0.5. Other parameters including 𝐹𝐴 ratio, CA ratio and 𝐷 are also considered through the current framework.
- 1 January 2022
- Published by Civilicom
- Vol. 1 (1) , 1-11
A New Framework for Determining the Gradation of Asphalt Mixtures
Strength and rutting resistance as well as durability are the main quality measures for any asphalt mix. While the strength and resistance of the asphalt mixture to permanent deformation are controlled by the aggregate interlock and aggregate packing, the durability of asphalt mixture depends on adequate volumetric characteristics and film thickness of asphalt mixture. Accordingly, providing an adequate interlock between aggregates and the aggregate packing is of high importance in designing a new asphalt mixture in order to produce desirable volumetric characteristics in asphalt mixture. A new framework for asphalt mixture gradation has been developed and designed following an intensive review of the various currently used approaches. The new framework considers all the controlling factors in the aggregate gradation design for optimum gradation of the asphalt mixtures. Satisfactory interlocking between aggregate particles, proper skeleton within the asphalt mixture, and acceptable volumetric properties are the main parameters to be considered for optimum gradation design for asphalt mix. The framework provides a systematic approach for the gradation process starting from the concentration at different sieves to finally account for the 𝐹𝐴 ≤ 0.5. Other parameters including 𝐹𝐴 ratio, CA ratio and 𝐷 are also considered through the current framework.
- 1 December 2020
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (7) , 2191-2205
Evaluation of volumetric performance of asphalt mixtures containing recycled construction aggregate (RCA)
High rate of construction and demolition waste materials results in a large amount of stockpiled waste materials. Pavement industry is now considering a sustainable approach for asphalt mixture design incorporating certain waste materials. This research investigates the feasibility of substitution of virgin aggregates in asphalt mixes with recycled construction aggregates (RCA) obtained from the construction and demolition sector. A preliminary experimental study including determination of flakiness index, particle shape, wet/dry strength variation, water absorption rate, particle density, crushing value, deleterious material and weak particles was conducted on blends of RCA and virgin aggregates to evaluate the engineering properties of aggregate blends. Different asphalt mixes incorporating RCA at different rates were prepared and evaluated using a gyratory compaction. The results of the regression analysis showed that the asphalt mixtures containing 20% to 22% RCA provide comparable volumetric properties as the control sample, while mixes with higher RCA substitutions achieved higher air voids, and lower voids in the mineral aggregate (VMA), voids filled with asphalt (VFA) and binder film index (BFI). The results of this study suggested a feasible use of RCA for partial aggregate replacement in hot mix asphalt (HMA).
- 1 December 2020
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 23 (7) , 2191-2205
Evaluation of volumetric performance of asphalt mixtures containing recycled construction aggregate (RCA)
High rate of construction and demolition waste materials results in a large amount of stockpiled waste materials. Pavement industry is now considering a sustainable approach for asphalt mixture design incorporating certain waste materials. This research investigates the feasibility of substitution of virgin aggregates in asphalt mixes with recycled construction aggregates (RCA) obtained from the construction and demolition sector. A preliminary experimental study including determination of flakiness index, particle shape, wet/dry strength variation, water absorption rate, particle density, crushing value, deleterious material and weak particles was conducted on blends of RCA and virgin aggregates to evaluate the engineering properties of aggregate blends. Different asphalt mixes incorporating RCA at different rates were prepared and evaluated using a gyratory compaction. The results of the regression analysis showed that the asphalt mixtures containing 20% to 22% RCA provide comparable volumetric properties as the control sample, while mixes with higher RCA substitutions achieved higher air voids, and lower voids in the mineral aggregate (VMA), voids filled with asphalt (VFA) and binder film index (BFI). The results of this study suggested a feasible use of RCA for partial aggregate replacement in hot mix asphalt (HMA).
- 1 January 2020
- Published by Elsevier in Journal of Environmental Management
- Vol. 254, 109809
Performance comparison of a MSW settlement prediction model in Tehran landfill
- 1 January 2020
- Published by Elsevier in Journal of Environmental Management
- Vol. 254, 109809
Performance comparison of a MSW settlement prediction model in Tehran landfill
- Open Access
- 10 April 2019
- Published by MDPI AG in Journal of Composites Science
- Vol. 3 (2) , 40
Structural Performance of Polyurethane Foam-Filled Building Composite Panels: A State-Of-The-Art
Composite panels with polyurethane (PU) foam-core and facing materials, such as gypsum, engineered wood or some composite materials, are being used as structural members in building construction. This paper reviews and summarises major research developments, and provides an updated review of references on the structural performance of foam-filled building composite panels from 1998 to 2017. The review revealed that previous studies on the structural performance of foam-filled building composite panels could be categorised into five themes; namely, energy absorption and dynamic behaviour; bending and shear behaviour, edgewise and flatwise compressive/tensile behaviour; delamination/deboning issues; and finally some miscellaneous issues. These categories comprise approximately 30%, 40%, 11%, 11% and 8% of related studies over the last two decades, respectively. Also, over the past five years, the number of relevant studies has increased by ~400% relative to the previous similar periods, indicating the attention and focus of researchers to the importance of the structural performance of foam-filled composite panels.
- 10 April 2019
- Published by MDPI AG in Journal of Composites Science
- Vol. 3 (2) , 40
Open AccessStructural Performance of Polyurethane Foam-Filled Building Composite Panels: A State-Of-The-Art
Composite panels with polyurethane (PU) foam-core and facing materials, such as gypsum, engineered wood or some composite materials, are being used as structural members in building construction. This paper reviews and summarises major research developments, and provides an updated review of references on the structural performance of foam-filled building composite panels from 1998 to 2017. The review revealed that previous studies on the structural performance of foam-filled building composite panels could be categorised into five themes; namely, energy absorption and dynamic behaviour; bending and shear behaviour, edgewise and flatwise compressive/tensile behaviour; delamination/deboning issues; and finally some miscellaneous issues. These categories comprise approximately 30%, 40%, 11%, 11% and 8% of related studies over the last two decades, respectively. Also, over the past five years, the number of relevant studies has increased by ~400% relative to the previous similar periods, indicating the attention and focus of researchers to the importance of the structural performance of foam-filled composite panels.
- Open Access
- 8 March 2019
- Published by MDPI AG in Preprints.org
Nutrient Resources Recovery by a Creative Co-Composting Method of Municipal Solid Wastes and Wastewater Treatment Plant Sludge
The purpose of this study is nutrient resources recovery by achieving the optimal chemical oxygen demand (COD) and carbon to nitrogen ratio (C/N) in co-composting wastewater treatment plant sludge with Municipal Solid Wastes (MSW). In this effort, the co-composting has been conducted in form of a case study in the northern region of Iran. In this research, 192 tests were carried out on four series of samples examined in terms of waste to sludge ratio, different aeration period, the percent of porous materials and the moisture content. This study was carried out at a temperature of 50 °C for a 15 day period by application of the in-vessel system and shows that the best ratio for waste to sludge is 2:1, while the 8 hour period is the best aeration period. The porous material which can be added to the composting process is limited to 15% in weight. In other words, any more or less amount of this material will adversely impact the process. Moreover, this research suggests that the sludge dewatering is not required in such processes. In Addition, the efficiency of both COD and C/N reductions equals to about 40%.
- 8 March 2019
- Published by MDPI AG in Preprints.org
Open AccessNutrient Resources Recovery by a Creative Co-Composting Method of Municipal Solid Wastes and Wastewater Treatment Plant Sludge
The purpose of this study is nutrient resources recovery by achieving the optimal chemical oxygen demand (COD) and carbon to nitrogen ratio (C/N) in co-composting wastewater treatment plant sludge with Municipal Solid Wastes (MSW). In this effort, the co-composting has been conducted in form of a case study in the northern region of Iran. In this research, 192 tests were carried out on four series of samples examined in terms of waste to sludge ratio, different aeration period, the percent of porous materials and the moisture content. This study was carried out at a temperature of 50 °C for a 15 day period by application of the in-vessel system and shows that the best ratio for waste to sludge is 2:1, while the 8 hour period is the best aeration period. The porous material which can be added to the composting process is limited to 15% in weight. In other words, any more or less amount of this material will adversely impact the process. Moreover, this research suggests that the sludge dewatering is not required in such processes. In Addition, the efficiency of both COD and C/N reductions equals to about 40%.