Ali Khodaii
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ali Khodaii has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Fereidoon Moghadas Nejad
Department of Civil & Environmental Engineering, Amirkabir University of Technology (Tehran Polytechnic), Tehran, Iran
17 shared publications - Pouria Hajikarimi
Department of Civil and Environmental Engineering, Amirkabir University of Technology, Tehran, Iran
8 shared publications - Joseph Absi
Univ. of Limoges
6 shared publications Pouria Hajikarimi
Department of Civil and Environmental Engineering, Amirkabir University of Technology (Tehran Polytechnic)
6 shared publications- Amir Mehrara
Amirkabir University of Technology
4 shared publications - Meeghat Habibian
Amirkabir University of Technology
4 shared publications
Latest Publications
- 20 August 2026
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 27 (1)
A multi-scale investigation of the fractional viscoelastic properties of rejuvenated recycled asphalt mixtures: experimental approach
1. The use of recycled asphalt mixtures in pavement engineering has expanded rapidly due to their sustainability and cost efficiency (Gholami et al., 2025; Zhong et al., 2024). These asphalt mixtur...
- 20 August 2026
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 27 (1)
A multi-scale investigation of the fractional viscoelastic properties of rejuvenated recycled asphalt mixtures: experimental approach
1. The use of recycled asphalt mixtures in pavement engineering has expanded rapidly due to their sustainability and cost efficiency (Gholami et al., 2025; Zhong et al., 2024). These asphalt mixtur...
- Open Access
- 16 February 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Correlations among chemical and rheological aging indices/indicators of asphalt binder at high temperatures
This study examines the relationships between chemical and rheological–viscoelastic aging indicators of asphalt binders to clarify how oxidation-induced changes are reflected in high-temperature performance. Three neat binders with penetration grades of 40–50, 60–70, and 85–100 were subjected to short-term and then progressive long-term aging using the Rolling Thin Film Oven and multiple Pressure Aging Vessel (PAV) cycles. Aging was characterized using Fourier Transform Infrared (FTIR) spectroscopy, dynamic shear rheometry, and rotational viscosity measurements. While most previous studies have either examined relationships between a limited number of chemical and rheological indicators or focused exclusively on rheological aging indices, this study evaluates multiple key indicators, including an FTIR-based combined carbonyl–sulfoxide aging index, the Superpave rutting parameter (G*/sinδ), zero shear viscosity (ZSV), apparent viscosity, and selected parameters of the 2S2P1D viscoelastic model. The results show that all indicators increase with aging, with the most pronounced changes occurring during the first PAV cycle. The FTIR-based combined carbonyl–sulfoxide index effectively reflects aging progression, and strong correlations were observed between chemical and rheological indices, including linear relationships between the FTIR aging index and both Log(ZSV) and the 2S2P1D α parameter, as well as a strong relationship between apparent viscosity and G*/sinδ. In addition, the Superpave parameter G*/sinδ at 60 °C exhibited a strong power-law correlation with the FTIR aging index and a robust exponential relationship with Log(ZSV) at the same temperature. These findings demonstrate that chemical oxidation is consistently reflected in rheological–viscoelastic behavior and reveal robust, trend-based relationships that can support flexible interpretation of binder aging and provide a basis for simplified, data-driven aging assessment.
- 16 February 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessCorrelations among chemical and rheological aging indices/indicators of asphalt binder at high temperatures
This study examines the relationships between chemical and rheological–viscoelastic aging indicators of asphalt binders to clarify how oxidation-induced changes are reflected in high-temperature performance. Three neat binders with penetration grades of 40–50, 60–70, and 85–100 were subjected to short-term and then progressive long-term aging using the Rolling Thin Film Oven and multiple Pressure Aging Vessel (PAV) cycles. Aging was characterized using Fourier Transform Infrared (FTIR) spectroscopy, dynamic shear rheometry, and rotational viscosity measurements. While most previous studies have either examined relationships between a limited number of chemical and rheological indicators or focused exclusively on rheological aging indices, this study evaluates multiple key indicators, including an FTIR-based combined carbonyl–sulfoxide aging index, the Superpave rutting parameter (G*/sinδ), zero shear viscosity (ZSV), apparent viscosity, and selected parameters of the 2S2P1D viscoelastic model. The results show that all indicators increase with aging, with the most pronounced changes occurring during the first PAV cycle. The FTIR-based combined carbonyl–sulfoxide index effectively reflects aging progression, and strong correlations were observed between chemical and rheological indices, including linear relationships between the FTIR aging index and both Log(ZSV) and the 2S2P1D α parameter, as well as a strong relationship between apparent viscosity and G*/sinδ. In addition, the Superpave parameter G*/sinδ at 60 °C exhibited a strong power-law correlation with the FTIR aging index and a robust exponential relationship with Log(ZSV) at the same temperature. These findings demonstrate that chemical oxidation is consistently reflected in rheological–viscoelastic behavior and reveal robust, trend-based relationships that can support flexible interpretation of binder aging and provide a basis for simplified, data-driven aging assessment.
- Open Access
- 10 April 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-21
A multifaceted purpose-oriented approach to evaluate material circularity index for rejuvenated recycled asphalt mixtures
This study investigates the impact of different mechanical properties, test procedures, and environmental and economic factors on the Material Circularity Index (MCI) of rejuvenated recycled asphalt mixtures. Four mixtures, including new and rejuvenated mixtures with 35%, 50%, and 65% reclaimed asphalt pavement (RAP), were evaluated using resilient modulus, moisture susceptibility, indirect tensile fatigue, semi-circular bending, and dynamic creep tests. A novel definition of MCI was introduced, integrating cost, CO2 emissions, and mechanical properties. Results indicate that the 50% RAP mixture consistently performed best across a range of scenarios, especially in varying climates and when multiple performance criteria were considered, with an MCI ranging from 0.38 to 0.83. Meanwhile, the 65% RAP mixture was optimal when cost and environmental considerations were prioritized, particularly in moderate to low temperatures. The findings also imply the importance of selecting appropriate performance parameters and test methods, as the choice of dynamic creep test procedures was shown to significantly influence MCI values. Ultimately, this study demonstrates that the MCI can serve as a multi-conceptual index for selecting appropriate asphalt mixtures. This process ensures a sustainable, performance-based asphalt mixture selection by integrating regional conditions, performance needs, and environmental factors.
- 10 April 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-21
Open AccessA multifaceted purpose-oriented approach to evaluate material circularity index for rejuvenated recycled asphalt mixtures
This study investigates the impact of different mechanical properties, test procedures, and environmental and economic factors on the Material Circularity Index (MCI) of rejuvenated recycled asphalt mixtures. Four mixtures, including new and rejuvenated mixtures with 35%, 50%, and 65% reclaimed asphalt pavement (RAP), were evaluated using resilient modulus, moisture susceptibility, indirect tensile fatigue, semi-circular bending, and dynamic creep tests. A novel definition of MCI was introduced, integrating cost, CO2 emissions, and mechanical properties. Results indicate that the 50% RAP mixture consistently performed best across a range of scenarios, especially in varying climates and when multiple performance criteria were considered, with an MCI ranging from 0.38 to 0.83. Meanwhile, the 65% RAP mixture was optimal when cost and environmental considerations were prioritized, particularly in moderate to low temperatures. The findings also imply the importance of selecting appropriate performance parameters and test methods, as the choice of dynamic creep test procedures was shown to significantly influence MCI values. Ultimately, this study demonstrates that the MCI can serve as a multi-conceptual index for selecting appropriate asphalt mixtures. This process ensures a sustainable, performance-based asphalt mixture selection by integrating regional conditions, performance needs, and environmental factors.
- 4 June 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 435
Long-term aging simulation of asphalt mixture: A comparative experimental study
- 4 June 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 435
Long-term aging simulation of asphalt mixture: A comparative experimental study
- Open Access
- 26 October 2023
- Published by Elsevier in Journal of Public Transportation
- Vol. 25
Enriching smart card data with the trip purpose attribute
- 26 October 2023
- Published by Elsevier in Journal of Public Transportation
- Vol. 25
Open AccessEnriching smart card data with the trip purpose attribute
- 4 February 2023
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 24 (1)
Investigation of the effect of acid sludge neutralization treatment on producing a sustainable eco-friendly additive for bituminous composites
Acid sludge is an environmental pollutant that is produced daily in large amounts in used engine oil refineries. Recycling this waste is the primary goal of this paper. This study used ‘washing with water’ and ‘neutralization with quicklime’ methods to prepare acid sludge for use in bituminous materials as huge potential disposal. The neutralised sludge by the ‘washing with water’ method was added to bitumen in the wet blending process at 10, 20, and 30 wt%. This product is brittle without proper adhesion and cohesion and cannot meet the standard limits as an acceptable binder. It performs like long-term aged bitumen, reducing penetration and ductility and increasing the aging potential and viscosity. In another method, the neutralised sludge by adding quicklime was added to the asphalt mixture to replace fine aggregates in 50, 75, and 100 wt%. Using this product decreases the aging potential and moisture susceptibility up to 36.4, and increases rutting resistance up to 34.7%, indirect tensile strength up to 17.3%, and resilient modulus up to 17.3%. Despite the presence of large amounts of heavy metals in acid sludge, using this product in asphalt mixtures is an economical and completely hygienic solution for disposing of acid sludge.
- 4 February 2023
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 24 (1)
Investigation of the effect of acid sludge neutralization treatment on producing a sustainable eco-friendly additive for bituminous composites
Acid sludge is an environmental pollutant that is produced daily in large amounts in used engine oil refineries. Recycling this waste is the primary goal of this paper. This study used ‘washing with water’ and ‘neutralization with quicklime’ methods to prepare acid sludge for use in bituminous materials as huge potential disposal. The neutralised sludge by the ‘washing with water’ method was added to bitumen in the wet blending process at 10, 20, and 30 wt%. This product is brittle without proper adhesion and cohesion and cannot meet the standard limits as an acceptable binder. It performs like long-term aged bitumen, reducing penetration and ductility and increasing the aging potential and viscosity. In another method, the neutralised sludge by adding quicklime was added to the asphalt mixture to replace fine aggregates in 50, 75, and 100 wt%. Using this product decreases the aging potential and moisture susceptibility up to 36.4, and increases rutting resistance up to 34.7%, indirect tensile strength up to 17.3%, and resilient modulus up to 17.3%. Despite the presence of large amounts of heavy metals in acid sludge, using this product in asphalt mixtures is an economical and completely hygienic solution for disposing of acid sludge.