Mats Norell
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mats Norell has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Lars Nyborg
Department of Industrial and Materials Science, Chalmers University of Technology, 41296 Gothenburg, Sweden
8 shared publications F. Tholence
Chalmers University of Technology
5 shared publicationsJ.-E. Svensson
Chalmers University of Technology
5 shared publications- Yu Cao
Department of Mechanical Engineering, Chalmers University of Technology
5 shared publications L.-G. Johansson
Chalmers University of Technology
4 shared publicationsK. Hellström
Chalmers University of Technology
3 shared publications
Latest Publications
- Open Access
- 21 March 2019
- Published by Taylor & Francis in Tribology Transactions
- Vol. 62 (3) , 412-418
Effect of Running-In (Load and Speed) on Surface Characteristics of Honed Gears
The initial running-in cycles alter the surface integrity characteristics and influence gear performance. Presented here are how the surface characteristics of honed spur gears evolved due to the combined effect of running-in load (0.9 or 1.7 GPa) and speed (0.5 or 8.3 m/sec) in FZG tests. Running-in effected the surface layers to a depth of 5 µm. High running-in load promoted plastic deformation of asperities, created microstructural changes associated with surface cracks and relaxed residual stresses. It also enhanced the amount of Phosphorous from EP additives at the surface. The surface contact fatigue failure i.e. micropitting was promoted by running-in speed rather than load.
- 21 March 2019
- Published by Taylor & Francis in Tribology Transactions
- Vol. 62 (3) , 412-418
Open AccessEffect of Running-In (Load and Speed) on Surface Characteristics of Honed Gears
The initial running-in cycles alter the surface integrity characteristics and influence gear performance. Presented here are how the surface characteristics of honed spur gears evolved due to the combined effect of running-in load (0.9 or 1.7 GPa) and speed (0.5 or 8.3 m/sec) in FZG tests. Running-in effected the surface layers to a depth of 5 µm. High running-in load promoted plastic deformation of asperities, created microstructural changes associated with surface cracks and relaxed residual stresses. It also enhanced the amount of Phosphorous from EP additives at the surface. The surface contact fatigue failure i.e. micropitting was promoted by running-in speed rather than load.
- 1 November 2017
- Published by Elsevier in Tribology International
- Vol. 115, 45-58
Influence of running-in on surface characteristics of efficiency tested ground gears
- 1 November 2017
- Published by Elsevier in Tribology International
- Vol. 115, 45-58
Influence of running-in on surface characteristics of efficiency tested ground gears
- 1 April 2017
- Published by SAGE Publications in Surface Engineering
- Vol. 33 (4) , 319-326
Thermal decomposition of N-expanded austenite in 304L and 904L steels
In this study, expanded austenite was prepared by an industrial low-temperature plasma nitriding process in 304L and 904L austenitic stainless steels. The current investigation focuses on the assessment of the thermal stability and related phase evolution of the expanded austenite layer during isothermal annealing in protective argon atmosphere at temperatures ranging from 450 to 600°C for 24 and 168 h. Characterisation of the original expanded austenite and the decomposed surface layers was performed. Denitriding, inward N-diffusion and Cr-compounds precipitation occurred at different extent, depending on annealing conditions and alloy composition. Expanded austenite in 304L exhibited a near complete eutectoid decomposition after a short annealing time, while 904L showed significantly better thermal stability. A fine dispersion of small CrN precipitates resulting from expanded austenite decomposition at relatively low annealing temperature or short duration could further positively affect the surface hardness of both materials. Precipitate growth reduces hardness at higher annealing temperatures/times.
- 1 April 2017
- Published by SAGE Publications in Surface Engineering
- Vol. 33 (4) , 319-326
Thermal decomposition of N-expanded austenite in 304L and 904L steels
In this study, expanded austenite was prepared by an industrial low-temperature plasma nitriding process in 304L and 904L austenitic stainless steels. The current investigation focuses on the assessment of the thermal stability and related phase evolution of the expanded austenite layer during isothermal annealing in protective argon atmosphere at temperatures ranging from 450 to 600°C for 24 and 168 h. Characterisation of the original expanded austenite and the decomposed surface layers was performed. Denitriding, inward N-diffusion and Cr-compounds precipitation occurred at different extent, depending on annealing conditions and alloy composition. Expanded austenite in 304L exhibited a near complete eutectoid decomposition after a short annealing time, while 904L showed significantly better thermal stability. A fine dispersion of small CrN precipitates resulting from expanded austenite decomposition at relatively low annealing temperature or short duration could further positively affect the surface hardness of both materials. Precipitate growth reduces hardness at higher annealing temperatures/times.
- Open Access
- 18 March 2015
- Published by Springer Nature in Oxidation of Metals
- Vol. 84 (1-2) , 105-127
A Microstructural and Kinetic Investigation of the KCl-Induced Corrosion of an FeCrAl Alloy at 600 °C
- 18 March 2015
- Published by Springer Nature in Oxidation of Metals
- Vol. 84 (1-2) , 105-127
Open AccessA Microstructural and Kinetic Investigation of the KCl-Induced Corrosion of an FeCrAl Alloy at 600 °C
- 1 January 2015
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 17, 120-126
Surface oxidation behavior of Ti–6Al–4V manufactured by Electron Beam Melting (EBM®)
- 1 January 2015
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 17, 120-126
Surface oxidation behavior of Ti–6Al–4V manufactured by Electron Beam Melting (EBM®)
- 10 September 2014
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 28 (9) , 6116-6129
Mitigation of Fireside Corrosion in Power Plants: The Combined Effect of Sulfur Dioxide and Potassium Chloride on the Corrosion of a FeCrAl Alloy
- 10 September 2014
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 28 (9) , 6116-6129
Mitigation of Fireside Corrosion in Power Plants: The Combined Effect of Sulfur Dioxide and Potassium Chloride on the Corrosion of a FeCrAl Alloy
- 18 July 2014
- Published by Springer Nature in Oxidation of Metals
- Vol. 82 (3-4) , 225-247
The Initial Oxide Scale Development on a Model FeNiCrAl Alloy at 900 °C in Dry and Humid Atmosphere: A Detailed Investigation
- 18 July 2014
- Published by Springer Nature in Oxidation of Metals
- Vol. 82 (3-4) , 225-247
The Initial Oxide Scale Development on a Model FeNiCrAl Alloy at 900 °C in Dry and Humid Atmosphere: A Detailed Investigation
- Open Access
- 10 April 2014
- Published by Wiley in Surface and Interface Analysis
- Vol. 46 (10-11) , 856-860
Multi‐technique characterization of low‐temperature plasma nitrided austenitic AISI 304L and AISI 904L stainless steel
The current study focuses on the characterization of the nitrided layer, formed in American Iron and Steel Institute (AISI) 304L and AISI 904L austenitic stainless steels by industrial low‐temperature plasma nitriding, using combined analysis techniques. The study highlighted that the evolution of the microstructure of the nitrided layers is influenced by surface finishing prior to nitriding, alloying elements and nitriding conditions, all factors affecting S‐phase formation and nitrogen (N) diffusion mechanisms. The chemical bonding characteristics of Cr 2p 3/2 and N 1s as revealed by XPS show a shift in binding energy between expanded austenite (S‐phase) and CrN‐like compounds. S‐phase has proven to be more stable in 904L, whereas residual and/or induced ferrite/martensite in 304L acts as a barrier for its development. © 2014 The Authors. Surface and Interface Analysis published by John Wiley & Sons, Ltd.
- 10 April 2014
- Published by Wiley in Surface and Interface Analysis
- Vol. 46 (10-11) , 856-860
Open AccessMulti‐technique characterization of low‐temperature plasma nitrided austenitic AISI 304L and AISI 904L stainless steel
The current study focuses on the characterization of the nitrided layer, formed in American Iron and Steel Institute (AISI) 304L and AISI 904L austenitic stainless steels by industrial low‐temperature plasma nitriding, using combined analysis techniques. The study highlighted that the evolution of the microstructure of the nitrided layers is influenced by surface finishing prior to nitriding, alloying elements and nitriding conditions, all factors affecting S‐phase formation and nitrogen (N) diffusion mechanisms. The chemical bonding characteristics of Cr 2p 3/2 and N 1s as revealed by XPS show a shift in binding energy between expanded austenite (S‐phase) and CrN‐like compounds. S‐phase has proven to be more stable in 904L, whereas residual and/or induced ferrite/martensite in 304L acts as a barrier for its development. © 2014 The Authors. Surface and Interface Analysis published by John Wiley & Sons, Ltd.
- 1 April 2013
- Published by SAGE Publications in Powder Metallurgy
- Vol. 56 (2) , 158-163
Surface characterisation of fine inert gas and water atomised stainless steel 316L powders: formation of thermodynamically unstable surface oxide phases
- 1 April 2013
- Published by SAGE Publications in Powder Metallurgy
- Vol. 56 (2) , 158-163
Surface characterisation of fine inert gas and water atomised stainless steel 316L powders: formation of thermodynamically unstable surface oxide phases