Rajesh Ganesan
Research Subjects
Rajesh Ganesan has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Marcela Milena Marie Bilek
The University of Sydney
8 shared publications - David Robert McKenzie
The University of Sydney
7 shared publications - Dougal G. McCulloch
RMIT University
6 shared publications - James G. Partridge
Department of Physics RMIT University Melbourne Victoria Australia
5 shared publications - A. E. Ross
School of Physics A28, The University of Sydney, NSW 2006, AUSTRALIA
3 shared publications B Treverrow
School of Physics, The University of Sydney, Sydney, NSW 2006, Australia
2 shared publications
Latest Publications
- Open Access
- 14 February 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (2)
Room-temperature sputter deposition of gold-colored TiN assisted by niobium bombardment from a bipolar HiPIMS source
The deposition of gold-colored titanium nitride films without applying substrate heating is of significant interest due to the increasing demand for decorative coatings on temperature-sensitive three-dimensional substrates. Here, the energetic impact of Nb1+ ions during the deposition of TiN was achieved within a bipolar high-power impulse magnetron sputtering discharge operating on a Nb target. A separate titanium target was operated with direct current magnetron sputtering in the same reactive argon–nitrogen mixture. This process aimed to achieve a dense titanium nitride with the assistance of the niobium ion bombardment. The niobium controlled the phase formation and structure of the resulting Nb-containing TiN coating without needing external heating. The niobium ion bombardment during deposition increases the density of the titanium nitride coatings, promoting the formation of the cubic phase favored for its gold color and excellent mechanical and tribological properties, including HF1-level adhesion. Energy-selective mass spectrometer investigations revealed an increase in the flux and the energy of titanium ions due to momentum transfer from niobium ions to titanium neutrals in the plasma generated between the targets and the substrate. The approach introduced here paves the way for the formation of the cubic phase of Nb-doped TiN films without external heating, producing coatings with combined decorative and protective properties.
- 14 February 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (2)
Open AccessRoom-temperature sputter deposition of gold-colored TiN assisted by niobium bombardment from a bipolar HiPIMS source
The deposition of gold-colored titanium nitride films without applying substrate heating is of significant interest due to the increasing demand for decorative coatings on temperature-sensitive three-dimensional substrates. Here, the energetic impact of Nb1+ ions during the deposition of TiN was achieved within a bipolar high-power impulse magnetron sputtering discharge operating on a Nb target. A separate titanium target was operated with direct current magnetron sputtering in the same reactive argon–nitrogen mixture. This process aimed to achieve a dense titanium nitride with the assistance of the niobium ion bombardment. The niobium controlled the phase formation and structure of the resulting Nb-containing TiN coating without needing external heating. The niobium ion bombardment during deposition increases the density of the titanium nitride coatings, promoting the formation of the cubic phase favored for its gold color and excellent mechanical and tribological properties, including HF1-level adhesion. Energy-selective mass spectrometer investigations revealed an increase in the flux and the energy of titanium ions due to momentum transfer from niobium ions to titanium neutrals in the plasma generated between the targets and the substrate. The approach introduced here paves the way for the formation of the cubic phase of Nb-doped TiN films without external heating, producing coatings with combined decorative and protective properties.
- 1 December 2016
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 76 (3) , 30801
A HiPIMS plasma source with a magnetic nozzle that accelerates ions: application in a thruster
We demonstrate a solid fuel electrodeless ion thruster that uses a magnetic nozzle to collimate and accelerate copper ions produced by a high power impulse magnetron sputtering discharge (HiPIMS). The discharge is initiated using argon gas but in a practical device the consumption of argon could be minimised by exploiting the self-sputtering of copper. The ion fluence produced by the HiPIMS discharge was measured with a retarding field energy analyzer (RFEA) as a function of the magnetic field strength of the nozzle. The ion fraction of the copper was determined from the deposition rate of copper as a function of substrate bias and was found to exceed 87%. The ion fluence and ion energy increased in proportion with the magnetic field of the nozzle and the energy of the ions was found to follow a Maxwell-Boltzmann distribution with a directed velocity. The effectiveness of the magnetic nozzle in converting the randomized thermal motion of the ions into a jet was demonstrated from the energy distribution of the ions. The maximum ion exhaust velocity of at least 15.1 km/s, equivalent to a specific impulse of 1543 s was measured which is comparable to existing Hall thrusters and exceeds that of Teflon pulsed plasma thrusters.
- 1 December 2016
- Published by EDP Sciences in The European Physical Journal Applied Physics
- Vol. 76 (3) , 30801
A HiPIMS plasma source with a magnetic nozzle that accelerates ions: application in a thruster
We demonstrate a solid fuel electrodeless ion thruster that uses a magnetic nozzle to collimate and accelerate copper ions produced by a high power impulse magnetron sputtering discharge (HiPIMS). The discharge is initiated using argon gas but in a practical device the consumption of argon could be minimised by exploiting the self-sputtering of copper. The ion fluence produced by the HiPIMS discharge was measured with a retarding field energy analyzer (RFEA) as a function of the magnetic field strength of the nozzle. The ion fraction of the copper was determined from the deposition rate of copper as a function of substrate bias and was found to exceed 87%. The ion fluence and ion energy increased in proportion with the magnetic field of the nozzle and the energy of the ions was found to follow a Maxwell-Boltzmann distribution with a directed velocity. The effectiveness of the magnetic nozzle in converting the randomized thermal motion of the ions into a jet was demonstrated from the energy distribution of the ions. The maximum ion exhaust velocity of at least 15.1 km/s, equivalent to a specific impulse of 1543 s was measured which is comparable to existing Hall thrusters and exceeds that of Teflon pulsed plasma thrusters.
- 8 September 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 120 (10) , 103301
Pulsed external magnetic fields increase the deposition rate in reactive HiPIMS while preserving stoichiometry: An application to amorphous HfO2
We compare the use of externally applied pulsed and steady magnetic fields for the enhancement of deposition rate in reactive High Power Impulse Magnetron Sputtering (HiPIMS), using the deposition of amorphous hafnium oxide (a-HfO2) on Si as an example. The external magnetic fields were applied by a solenoidal coil, placed above the magnetron target. In the case of a steady magnetic field, a higher voltage was required to initiate the HiPIMS discharge, a longer delay time was observed for current onset, and the films became substoichiometric. For the pulsed magnetic field, film stoichiometry was maintained under all applied external magnetic field strengths. Varying the duration and delay times of the magnetic field after the application of HiPIMS voltage pulse revealed that the afterglow of the plasma between HiPIMS pulses was actively quenched by the presence of the magnetic field. Therefore, the optimum operation with the highest plasma density was obtained by applying the external magnetic field only when the plasma was established and removing it at the end of the HiPIMS pulse. A model to explain the findings is presented in which the target poisoning by oxide formation is determined by the conditions in the afterglow. We describe an approach to achieve maximum deposition rate while maintaining film stoichiometry and high film quality. Amorphous HfO2 films with leakage current through the film of less than 5 × 10−5 A/cm2 at 0.1 MV/cm were obtained at the maximum deposition rate. The refractive index, at a wavelength of 500 nm, of the film prepared with pulsed magnetic field was 2.05 with a very low extinction coefficient of 8 × 10−5.
- 8 September 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 120 (10) , 103301
Pulsed external magnetic fields increase the deposition rate in reactive HiPIMS while preserving stoichiometry: An application to amorphous HfO2
We compare the use of externally applied pulsed and steady magnetic fields for the enhancement of deposition rate in reactive High Power Impulse Magnetron Sputtering (HiPIMS), using the deposition of amorphous hafnium oxide (a-HfO2) on Si as an example. The external magnetic fields were applied by a solenoidal coil, placed above the magnetron target. In the case of a steady magnetic field, a higher voltage was required to initiate the HiPIMS discharge, a longer delay time was observed for current onset, and the films became substoichiometric. For the pulsed magnetic field, film stoichiometry was maintained under all applied external magnetic field strengths. Varying the duration and delay times of the magnetic field after the application of HiPIMS voltage pulse revealed that the afterglow of the plasma between HiPIMS pulses was actively quenched by the presence of the magnetic field. Therefore, the optimum operation with the highest plasma density was obtained by applying the external magnetic field only when the plasma was established and removing it at the end of the HiPIMS pulse. A model to explain the findings is presented in which the target poisoning by oxide formation is determined by the conditions in the afterglow. We describe an approach to achieve maximum deposition rate while maintaining film stoichiometry and high film quality. Amorphous HfO2 films with leakage current through the film of less than 5 × 10−5 A/cm2 at 0.1 MV/cm were obtained at the maximum deposition rate. The refractive index, at a wavelength of 500 nm, of the film prepared with pulsed magnetic field was 2.05 with a very low extinction coefficient of 8 × 10−5.
- 12 May 2016
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 49 (24) , 245201
Duty cycle control in reactive high-power impulse magnetron sputtering of hafnium and niobium
Instabilities in reactive sputtering have technological consequences and have been attributed to the formation of a compound layer on the target surface ('poisoning'). Here we demonstrate how the duty cycle of high power impulse magnetron sputtering (HiPIMS) can be used to control the surface conditions of Hf and Nb targets. Variations in the time resolved target current characteristics as a function of duty cycle were attributed to gas rarefaction and to the degree of poisoning of the target surface. As the operation transitions from Ar driven sputtering to metal driven sputtering, the secondary electron emission changes and reduces the target current. The target surface transitions smoothly from a poisoned state at low duty cycles to a quasi-metallic state at high duty cycles. Appropriate selection of duty cycle increases the deposition rate, eliminates the need for active regulation of oxygen flow and enables stable reactive deposition of stoichiometric metal oxide films. A model is presented for the reactive HIPIMS process in which the target operates in a partially poisoned mode with different degrees of oxide layer distribution on its surface that depends on the duty cycle. Finally, we show that by tuning the pulse characteristics, the refractive indices of the metal oxides can be controlled without increasing the absorption coefficients, a result important for the fabrication of optical multilayer stacks.
- 12 May 2016
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 49 (24) , 245201
Duty cycle control in reactive high-power impulse magnetron sputtering of hafnium and niobium
Instabilities in reactive sputtering have technological consequences and have been attributed to the formation of a compound layer on the target surface ('poisoning'). Here we demonstrate how the duty cycle of high power impulse magnetron sputtering (HiPIMS) can be used to control the surface conditions of Hf and Nb targets. Variations in the time resolved target current characteristics as a function of duty cycle were attributed to gas rarefaction and to the degree of poisoning of the target surface. As the operation transitions from Ar driven sputtering to metal driven sputtering, the secondary electron emission changes and reduces the target current. The target surface transitions smoothly from a poisoned state at low duty cycles to a quasi-metallic state at high duty cycles. Appropriate selection of duty cycle increases the deposition rate, eliminates the need for active regulation of oxygen flow and enables stable reactive deposition of stoichiometric metal oxide films. A model is presented for the reactive HIPIMS process in which the target operates in a partially poisoned mode with different degrees of oxide layer distribution on its surface that depends on the duty cycle. Finally, we show that by tuning the pulse characteristics, the refractive indices of the metal oxides can be controlled without increasing the absorption coefficients, a result important for the fabrication of optical multilayer stacks.
- 21 April 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 119 (15) , 155303
Mixed-mode high-power impulse magnetron sputter deposition of tetrahedral amorphous carbon with pulse-length control of ionization
High-power impulse magnetron sputtering (HiPIMS) is used to deposit amorphous carbon thin films with sp3 fractions of 13% to 82%. Increasing the pulse length results in a transition from conventional HiPIMS deposition to a “mixed-mode” in which an arc triggers on the target surface, resulting in a large flux of carbon ions. The films are characterized using X-ray photoelectron spectroscopy, Raman spectroscopy, ellipsometry, nanoindentation, elastic recoil detection analysis, and measurements of stress and contact angle. All properties vary in a consistent manner, showing a high tetrahedral character only for long pulses, demonstrating that mixed-mode deposition is the source of the high carbon ion flux. Varying the substrate bias reveals an “energy window” effect, where the sp3 fraction of the films is greatest for a substrate bias around −100 V and decreases for higher or lower bias values. In the absence of bias, the films' properties show little dependence on the pulse length, showing that energetic ions are the origin of the highly tetrahedral character.
- 21 April 2016
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 119 (15) , 155303
Mixed-mode high-power impulse magnetron sputter deposition of tetrahedral amorphous carbon with pulse-length control of ionization
High-power impulse magnetron sputtering (HiPIMS) is used to deposit amorphous carbon thin films with sp3 fractions of 13% to 82%. Increasing the pulse length results in a transition from conventional HiPIMS deposition to a “mixed-mode” in which an arc triggers on the target surface, resulting in a large flux of carbon ions. The films are characterized using X-ray photoelectron spectroscopy, Raman spectroscopy, ellipsometry, nanoindentation, elastic recoil detection analysis, and measurements of stress and contact angle. All properties vary in a consistent manner, showing a high tetrahedral character only for long pulses, demonstrating that mixed-mode deposition is the source of the high carbon ion flux. Varying the substrate bias reveals an “energy window” effect, where the sp3 fraction of the films is greatest for a substrate bias around −100 V and decreases for higher or lower bias values. In the absence of bias, the films' properties show little dependence on the pulse length, showing that energetic ions are the origin of the highly tetrahedral character.
- 1 March 2016
- Published by Elsevier in Applied Surface Science
- Vol. 365, 336-341
Optimizing HiPIMS pressure for deposition of high-k (k = 18.3) amorphous HfO2
- 1 March 2016
- Published by Elsevier in Applied Surface Science
- Vol. 365, 336-341
Optimizing HiPIMS pressure for deposition of high-k (k = 18.3) amorphous HfO2
- 22 January 2016
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 49 (8) , 085201
Time-resolved vacuum-ultraviolet emission (λ = 60–120 nm) from a high pressure DBD-excited helium plasma: formation mechanisms of the fast component
We report time and wavelength resolved studies of the vacuum-ultraviolet (VUV) emission from a windowless dielectric barrier discharge (DBD) in helium. Short-pulse voltage excitation is utilised to clearly resolve the fast and slow temporal components of the Hopfield continuum between λ = 60–120 nm. Experimental results and theoretical modelling of the spectral distributions indicate that the two components of the VUV emission must originate from the same radiating molecular state—, and that two distinct pumping mechanisms populate this state. The time evolution of the fast component is found to correlate with that from the (0,0) molecular transition (λ = 513.4 nm). Thus the state is initially rapidly pumped via radiative cascade from higher molecular states. In addition, the observed band emissions from the molecular v=0 and v=0 states and the line emissions from the atomic He*(n = 3) states all exhibit similar temporal behaviour during the discharge excitation period. Our results are consistent with the recent report of Frost et al (J. Phys. B 34 1569 2001) concerning the existence of a so-called 'neglected channel' to fast production from He*(n = 3) atomic state precursors.
- 22 January 2016
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 49 (8) , 085201
Time-resolved vacuum-ultraviolet emission (λ = 60–120 nm) from a high pressure DBD-excited helium plasma: formation mechanisms of the fast component
We report time and wavelength resolved studies of the vacuum-ultraviolet (VUV) emission from a windowless dielectric barrier discharge (DBD) in helium. Short-pulse voltage excitation is utilised to clearly resolve the fast and slow temporal components of the Hopfield continuum between λ = 60–120 nm. Experimental results and theoretical modelling of the spectral distributions indicate that the two components of the VUV emission must originate from the same radiating molecular state—, and that two distinct pumping mechanisms populate this state. The time evolution of the fast component is found to correlate with that from the (0,0) molecular transition (λ = 513.4 nm). Thus the state is initially rapidly pumped via radiative cascade from higher molecular states. In addition, the observed band emissions from the molecular v=0 and v=0 states and the line emissions from the atomic He*(n = 3) states all exhibit similar temporal behaviour during the discharge excitation period. Our results are consistent with the recent report of Frost et al (J. Phys. B 34 1569 2001) concerning the existence of a so-called 'neglected channel' to fast production from He*(n = 3) atomic state precursors.
- 9 October 2015
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 48 (44) , 442001
Synthesis of highly tetrahedral amorphous carbon by mixed-mode HiPIMS sputtering
Tetrahedral amorphous carbon films with an sp 3 content of 80% have been produced by high power impulse magnetron sputtering (HiPIMS) operating in a mixed sputtering/arc mode. In this mode, short-lived cathode spots form in the magnetic racetrack and produce large numbers of carbon ions. The spots move rapidly, inhibiting the formation of macroparticles. An argon pressure below 2.5 mTorr was critical for obtaining films with high sp 3 content, high stress, large Tauc gap and symmetrical Raman spectra, and all four quantities were strongly correlated.
- 9 October 2015
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 48 (44) , 442001
Synthesis of highly tetrahedral amorphous carbon by mixed-mode HiPIMS sputtering
Tetrahedral amorphous carbon films with an sp 3 content of 80% have been produced by high power impulse magnetron sputtering (HiPIMS) operating in a mixed sputtering/arc mode. In this mode, short-lived cathode spots form in the magnetic racetrack and produce large numbers of carbon ions. The spots move rapidly, inhibiting the formation of macroparticles. An argon pressure below 2.5 mTorr was critical for obtaining films with high sp 3 content, high stress, large Tauc gap and symmetrical Raman spectra, and all four quantities were strongly correlated.
- 1 August 2015
- Published by Elsevier in Surface and Coatings Technology
- Vol. 275, 252-259
Fatigue durability and corrosion resistance of TiO2 films on CoCrMo alloy under cyclic deformation
- 1 August 2015
- Published by Elsevier in Surface and Coatings Technology
- Vol. 275, 252-259
Fatigue durability and corrosion resistance of TiO2 films on CoCrMo alloy under cyclic deformation
- 1 May 2015
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 24 (3)
The role of pulse length in target poisoning during reactive HiPIMS: application to amorphous HfO2
- 1 May 2015
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 24 (3)
The role of pulse length in target poisoning during reactive HiPIMS: application to amorphous HfO2