Rénal Backov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Rénal Backov has a total of 212 co-authors. Here are the top co-authors by number of shared publications:
- Clément Sanchez
University of Strasbourg
22 shared publications - Nicolas Brun
ICGM, Univ Montpellier, CNRS, ENSCM
17 shared publications - Florent Carn
Matière et Systèmes Complexes (MSC), UMR 7057 CNRS and Université Paris Cité, 10 rue Alice Domon et Léonie Duquet, Paris 75205 Cedex 13, France
15 shared publications Hervé Deleuze
Univ. Bordeaux, Institut des Sciences Moléculaires, UMR 5255 CNRS, F-33405 Talence, France
14 shared publicationsMartin Depardieu
CRPP UPR8641 CNRS University of Bordeaux 115 Avenue du Dr. Schweitzer 33600 Pessac France
11 shared publications- Véronique Schmitt
Centre de Recherche Paul Pascal, UMR CNRS 5031, Université de Bordeaux, Pessac, France
11 shared publications
Latest Publications
- Open Access
- 28 August 2026
- Published by Elsevier in SSRN Electronic Journal
Black TiO2@Silica Hierarchical Foams Obtained in Reducing-Agent-Free Conditions
The development of novel materials is critical for sustainable environmental remediation, providing efficient sorbents and catalysts. Photocatalysts are particularly promising because they convert solar energy into chemical reactivity. Titanium dioxide is widely studied owing to its stability, low cost and strong oxidative potential, but its wide band gap and limited visible-light absorption restrict its solar efficiency. Defect engineering, including the formation of ”black TiO2”, can improve light harvesting and charge-carrier dynamics. These strategies are usually developed as powdered materials, while TiO2 confinement is often addressed separately through coatings or deposition onto 2D supports. Integrating modified TiO2 directly into three-dimensional porous architectures would therefore combine tunable modified optical properties with improved accessibility, processability, mass transport and material recovery. Here, we report a modified synthesis route toward hierarchical TiO2@SiO2 monoliths derived from high internal phase emulsion systems, enabling both high TiO2 loading within a porous silica framework and the in situ formation of defect-rich ”black TiO2”. TiO2 reduction is achieved without additional external reducing agents such as NaBH4 or dihydrogen (H2), while preserving monolithic architecture and accessible hierarchical porosity. This strategy offers a simple route fostering defect-engineered self-standing TiO2/SiO2 monoliths in which optical absorption, interfacial accessibility and hierarchical transport pathways are combined within a single material.
- 28 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessBlack TiO2@Silica Hierarchical Foams Obtained in Reducing-Agent-Free Conditions
The development of novel materials is critical for sustainable environmental remediation, providing efficient sorbents and catalysts. Photocatalysts are particularly promising because they convert solar energy into chemical reactivity. Titanium dioxide is widely studied owing to its stability, low cost and strong oxidative potential, but its wide band gap and limited visible-light absorption restrict its solar efficiency. Defect engineering, including the formation of ”black TiO2”, can improve light harvesting and charge-carrier dynamics. These strategies are usually developed as powdered materials, while TiO2 confinement is often addressed separately through coatings or deposition onto 2D supports. Integrating modified TiO2 directly into three-dimensional porous architectures would therefore combine tunable modified optical properties with improved accessibility, processability, mass transport and material recovery. Here, we report a modified synthesis route toward hierarchical TiO2@SiO2 monoliths derived from high internal phase emulsion systems, enabling both high TiO2 loading within a porous silica framework and the in situ formation of defect-rich ”black TiO2”. TiO2 reduction is achieved without additional external reducing agents such as NaBH4 or dihydrogen (H2), while preserving monolithic architecture and accessible hierarchical porosity. This strategy offers a simple route fostering defect-engineered self-standing TiO2/SiO2 monoliths in which optical absorption, interfacial accessibility and hierarchical transport pathways are combined within a single material.
- 22 June 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (26) , 18826-18836
Self-Standing Macro-Mesocellular Inorganic Aerogels Obtained While Coupling a Direct Concentrated Emulsion, Sol–Gel Chemistry, and a Supercritical CO 2 Drying Process
A scCO2 drying/lixiviation process allows self-standing inorganic macrocelullar aerogels to be produced within 1 h. The applied depressurization rate permits the macrocellular internal throats to be tuned with native hydrodynamic instability. scCO2 treatment advantageously addresses lixiviation of the tensioactive molecules employed as the templating agent. Final calcined aero-Si(HIPE) materials, at the optimum temperature of 450 °C, afford a specific surface area of up to 1400 m2 g-1. The lower treatment temperature and lower tension-active contents dramatically reduce the carbon footprint penalty, compared with that of traditional xero-Si(HIPE). Further annealing of these aero-Si(HIPE) foams at 1200 °C drastically decreases the specific surface area while maintaining both the open macroposity and the self-standing character. Concomitantly, severe shrinkage and densification of the monoliths occur upon cristobalite crystallization. For the sake of making this generic endeavor, the scCO2 drying/lixiviation approach has also been extended to MUB-110, MUB-200, and MUB-300 co-oxide(HIPE) catalysts describing the same scenario of fostering the specific surface area, maintaining the monolith-type character and associated macroporous open tortuosity, and minimizing the carbon footprint penalty.
- 22 June 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (26) , 18826-18836
Self-Standing Macro-Mesocellular Inorganic Aerogels Obtained While Coupling a Direct Concentrated Emulsion, Sol–Gel Chemistry, and a Supercritical CO 2 Drying Process
A scCO2 drying/lixiviation process allows self-standing inorganic macrocelullar aerogels to be produced within 1 h. The applied depressurization rate permits the macrocellular internal throats to be tuned with native hydrodynamic instability. scCO2 treatment advantageously addresses lixiviation of the tensioactive molecules employed as the templating agent. Final calcined aero-Si(HIPE) materials, at the optimum temperature of 450 °C, afford a specific surface area of up to 1400 m2 g-1. The lower treatment temperature and lower tension-active contents dramatically reduce the carbon footprint penalty, compared with that of traditional xero-Si(HIPE). Further annealing of these aero-Si(HIPE) foams at 1200 °C drastically decreases the specific surface area while maintaining both the open macroposity and the self-standing character. Concomitantly, severe shrinkage and densification of the monoliths occur upon cristobalite crystallization. For the sake of making this generic endeavor, the scCO2 drying/lixiviation approach has also been extended to MUB-110, MUB-200, and MUB-300 co-oxide(HIPE) catalysts describing the same scenario of fostering the specific surface area, maintaining the monolith-type character and associated macroporous open tortuosity, and minimizing the carbon footprint penalty.
- 1 January 2026
- Published by Societe Chimique de France
- Vol. 510, 27-33
Photocatalyse hétérogène 3D : laissons passer la lumière
(Text in French) 3D induced heterogeneous photocatalysis: let the light shine in. While combining the sol-gel process and the physical-chemistry of complex fluids, through a one step process, it is possible conceiving monolithic oxide ceramics bearing a hierarchical porosity. Overall, an amorphous siliceous matrix being hierarchically organized is promoting the open-3D architectures cohesion where transitional metal oxide nanoparticles are randomly distributed. Thus, a florilegia of novel biphasic catalysts is emerging and are labelled hereafter as MUB, acronym that stands for “Matériaux de l’Université de Bordeaux”. Within these monolithic open frameworks, both mass and photonic transport are optimized, mimicking radiolarian exoskeletons as outstanding photocatalytic systems. This article focuses on the topic over volumic VOCs photo-abatement processes opening the path towards minimizing footprint penalty while bypassing restrictive and conventional 2D-based methodologies. Overall strategy where we let the light shine in.
- 1 January 2026
- Published by Societe Chimique de France
- Vol. 510, 27-33
Photocatalyse hétérogène 3D : laissons passer la lumière
(Text in French) 3D induced heterogeneous photocatalysis: let the light shine in. While combining the sol-gel process and the physical-chemistry of complex fluids, through a one step process, it is possible conceiving monolithic oxide ceramics bearing a hierarchical porosity. Overall, an amorphous siliceous matrix being hierarchically organized is promoting the open-3D architectures cohesion where transitional metal oxide nanoparticles are randomly distributed. Thus, a florilegia of novel biphasic catalysts is emerging and are labelled hereafter as MUB, acronym that stands for “Matériaux de l’Université de Bordeaux”. Within these monolithic open frameworks, both mass and photonic transport are optimized, mimicking radiolarian exoskeletons as outstanding photocatalytic systems. This article focuses on the topic over volumic VOCs photo-abatement processes opening the path towards minimizing footprint penalty while bypassing restrictive and conventional 2D-based methodologies. Overall strategy where we let the light shine in.
- 24 September 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (39) , 26760-26769
Mastering Syntheses of Siliceous Hierarchical Porous Self-Standing Monoliths through the Integration of the Sol–Gel Process, Complex Fluids, and a Planetary Mixer
Self-standing siliceous monoliths bearing hierarchical porosity have been synthesized while combining the sol-gel process, complex fluids, and a planetary mixer. The mechanically well-defined and a priori reproducible stirring procedure leads to a precise control over the final hierarchical porous characteristics of the materials: Both the macroscopic cell and interconnecting throat dimensions in the monoliths, i.e., macroporosity, can be tuned by choosing the rotation speed. The fabrication process also leads to well-defined macrocellular wall thicknesses that can be tuned in the range of 30-90 nm by stirring control. Final high internal phase emulsion-based siliceous materials, Si(HIPE), are offering around 80-90% porosity, decreasing with stirring speed, and a broadly mixing invariant BET specific surface area of about 860 ± 60 m2 g-1, where the microporous surface area is rather constant at 480 ± 20 m2 g-1, with the BJH (mesoporous) area being more spread in the range of 380 ± 80 m2 g-1.
- 24 September 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (39) , 26760-26769
Mastering Syntheses of Siliceous Hierarchical Porous Self-Standing Monoliths through the Integration of the Sol–Gel Process, Complex Fluids, and a Planetary Mixer
Self-standing siliceous monoliths bearing hierarchical porosity have been synthesized while combining the sol-gel process, complex fluids, and a planetary mixer. The mechanically well-defined and a priori reproducible stirring procedure leads to a precise control over the final hierarchical porous characteristics of the materials: Both the macroscopic cell and interconnecting throat dimensions in the monoliths, i.e., macroporosity, can be tuned by choosing the rotation speed. The fabrication process also leads to well-defined macrocellular wall thicknesses that can be tuned in the range of 30-90 nm by stirring control. Final high internal phase emulsion-based siliceous materials, Si(HIPE), are offering around 80-90% porosity, decreasing with stirring speed, and a broadly mixing invariant BET specific surface area of about 860 ± 60 m2 g-1, where the microporous surface area is rather constant at 480 ± 20 m2 g-1, with the BJH (mesoporous) area being more spread in the range of 380 ± 80 m2 g-1.
- Open Access
- 19 July 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (34) , 22703-22714
Carbon black structural effect within kraft black liquor-based poly(HIPE): enhanced hydrogen storage and electro-capacitive properties
A biopolymer derived from Kraft Black Liquor (KBL), a byproduct of the paper industry composed mainly of lignin and hemicellulose, has been successfully filled with three different types of carbon black (CB) that differ in their specific surface areas, sizes, shapes and surface heteroatoms. These composite CB–KBL dispersions have been subsequently employed to generate porous monoliths through an emulsion-polymerization templating process. After carbonization, the fillers' influence over the resulting carbon monolith structures and textures is investigated. In particular, beyond XRD, Raman spectroscopy demonstrates improved sample structuration through CB filler addition while nitrogen sorption measurements reveal the influence of the fillers over the final composite's porosities. Considering their properties and effectiveness, hydrogen storage at 77 K reveals that some materials offer up to 1.4 wt% of H2 storage capacity, being higher than that of some commercial carbon materials (with the same specific surface) offering 1.2 wt% hydrogen retention. When addressing their electrochemical energy storage properties, some of these electrode materials deliver extremely promising specific capacities and rate capabilities, with values up to 47 mA h g−1 at 1 A g−1 in alkaline electrolyte, higher than those of the well-known “YP-80F” commercial material tested under the same conditions. These enhanced energy storage properties, while employing a high tonnage paper industry by-product as a carbonaceous source and carbon blacks as structural and textural modifiers, render these materials realistic candidates favoring a sustainable energy transition.
- 19 July 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (34) , 22703-22714
Open AccessCarbon black structural effect within kraft black liquor-based poly(HIPE): enhanced hydrogen storage and electro-capacitive properties
A biopolymer derived from Kraft Black Liquor (KBL), a byproduct of the paper industry composed mainly of lignin and hemicellulose, has been successfully filled with three different types of carbon black (CB) that differ in their specific surface areas, sizes, shapes and surface heteroatoms. These composite CB–KBL dispersions have been subsequently employed to generate porous monoliths through an emulsion-polymerization templating process. After carbonization, the fillers' influence over the resulting carbon monolith structures and textures is investigated. In particular, beyond XRD, Raman spectroscopy demonstrates improved sample structuration through CB filler addition while nitrogen sorption measurements reveal the influence of the fillers over the final composite's porosities. Considering their properties and effectiveness, hydrogen storage at 77 K reveals that some materials offer up to 1.4 wt% of H2 storage capacity, being higher than that of some commercial carbon materials (with the same specific surface) offering 1.2 wt% hydrogen retention. When addressing their electrochemical energy storage properties, some of these electrode materials deliver extremely promising specific capacities and rate capabilities, with values up to 47 mA h g−1 at 1 A g−1 in alkaline electrolyte, higher than those of the well-known “YP-80F” commercial material tested under the same conditions. These enhanced energy storage properties, while employing a high tonnage paper industry by-product as a carbonaceous source and carbon blacks as structural and textural modifiers, render these materials realistic candidates favoring a sustainable energy transition.
- Open Access
- 9 January 2024
- Published by Wiley in ChemBioChem
- Vol. 25 (3) , e202300781
Tuning Chemoenzymatic Pd/Laccase Conformation Toward Optimized Heterogeneous Aerobic Oxidation
Heterogeneous chemoenzymatic catalysts differing in their spatial organization and relative orientation of their enzymatic laccase and Pd units confined into macrocellular silica foams were tested on veratryl alcohol oxidation. When operating under continuous flow, we show that the catalytic efficiency of hybrids is significantly enhanced when the Pd(II) complex is combined with a laccase exhibiting a surface located lysine next to the T1 oxidation site of the enzyme.
- 9 January 2024
- Published by Wiley in ChemBioChem
- Vol. 25 (3) , e202300781
Open AccessTuning Chemoenzymatic Pd/Laccase Conformation Toward Optimized Heterogeneous Aerobic Oxidation
Heterogeneous chemoenzymatic catalysts differing in their spatial organization and relative orientation of their enzymatic laccase and Pd units confined into macrocellular silica foams were tested on veratryl alcohol oxidation. When operating under continuous flow, we show that the catalytic efficiency of hybrids is significantly enhanced when the Pd(II) complex is combined with a laccase exhibiting a surface located lysine next to the T1 oxidation site of the enzyme.
- 10 November 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (46) , 16385-16394
Kraft Black Liquor as a Carbonaceous Source for the Generation of Porous Monolithic Materials and Applications toward Hydrogen Adsorption and Ultrastable Supercapacitors
High internal phase emulsions (HIPEs) have templated self-standing porous carbonaceous materials (carboHIPEs) while employing Kraft Black Liquor, a paper milling industry byproduct, as a carbon precursor source. As such, the starting emulsion has been prepared through a laboratory-made homogenizer, while native materials have been characterized at various length scales either with Raman spectrometry, X-ray diffraction (XRD), mercury intrusion porosimetry, and nitrogen absorption. After thermal carbonization, specific surface areas ranging from ∼600 m2 g-1 to 1500 m2 g-1 have been reached while maintaining a monolithic character. Despite a poor graphitization yield, the carbonaceous materials offer good electronic transport properties, reaching 31 S m-1. When tested toward energy storage applications, the native unwashed materials revealed a hydrogen storage of 0.07 wt % at 40 bar and room temperature (RT), while hydrogen retention is reaching 0.37 wt % at 40 bar and RT for the washed sample. When employed as supercapacitor electrodes, these carbonaceous foams are able to deliver high capacities of ∼140 F/g at 1 A/g, thereby matching the ones obtained from a commercial carbon reference, while additionally providing a restored remnant capacity of 120 F/g at 2 A/g over 5000 cycle numbers.
- 10 November 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (46) , 16385-16394
Kraft Black Liquor as a Carbonaceous Source for the Generation of Porous Monolithic Materials and Applications toward Hydrogen Adsorption and Ultrastable Supercapacitors
High internal phase emulsions (HIPEs) have templated self-standing porous carbonaceous materials (carboHIPEs) while employing Kraft Black Liquor, a paper milling industry byproduct, as a carbon precursor source. As such, the starting emulsion has been prepared through a laboratory-made homogenizer, while native materials have been characterized at various length scales either with Raman spectrometry, X-ray diffraction (XRD), mercury intrusion porosimetry, and nitrogen absorption. After thermal carbonization, specific surface areas ranging from ∼600 m2 g-1 to 1500 m2 g-1 have been reached while maintaining a monolithic character. Despite a poor graphitization yield, the carbonaceous materials offer good electronic transport properties, reaching 31 S m-1. When tested toward energy storage applications, the native unwashed materials revealed a hydrogen storage of 0.07 wt % at 40 bar and room temperature (RT), while hydrogen retention is reaching 0.37 wt % at 40 bar and RT for the washed sample. When employed as supercapacitor electrodes, these carbonaceous foams are able to deliver high capacities of ∼140 F/g at 1 A/g, thereby matching the ones obtained from a commercial carbon reference, while additionally providing a restored remnant capacity of 120 F/g at 2 A/g over 5000 cycle numbers.
- 7 August 2023
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 35 (16) , 6502-6516
Hierarchical Porous WO3@SiO2 Self-Standing Monolithic Catalysts and Their Efficient Cycling “Cosolvent-Free” Friedel–Crafts Alkylation/Acylation Catalytic Properties
- 7 August 2023
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 35 (16) , 6502-6516
Hierarchical Porous WO3@SiO2 Self-Standing Monolithic Catalysts and Their Efficient Cycling “Cosolvent-Free” Friedel–Crafts Alkylation/Acylation Catalytic Properties
- Open Access
- 23 May 2023
- Published by Wiley in Chempluschem
- Vol. 88 (5) , e202300156
Controlled Immobilization of a Palladium Complex/Laccase Hybrid into a Macrocellular Siliceous Host
This study investigates the site‐directed immobilization of a hybrid catalyst bearing a biquinoline‐based‐Pd(II) complex (1) and a robust laccase within cavities of a silica foam to favor veratryl alcohol oxidation. We performed the grafting of 1 at a unique surface located lysine of two laccase variants, either at closed (1⊂UNIK157) or opposite position (1⊂UNIK71) of the enzyme oxidation site. After immobilization into the cavities of silica monoliths bearing hierarchical porosity, we show that catalytic activity is dependent on the orientation and loading of each hybrid, 1⊂UNIK157 being twice as active than 1⊂UNIK71 (203 TON vs 100 TON) when operating under continuous flow. These systems can be reused 5 times, with an operational activity remaining as high as 40 %. We show that the synergy between 1 and laccase can be tuned within the foam. This work is a proof of concept for controlling the organization of a heterogeneous hybrid catalyst using a Pd/laccase/silica foam.
- 23 May 2023
- Published by Wiley in Chempluschem
- Vol. 88 (5) , e202300156
Open AccessControlled Immobilization of a Palladium Complex/Laccase Hybrid into a Macrocellular Siliceous Host
This study investigates the site‐directed immobilization of a hybrid catalyst bearing a biquinoline‐based‐Pd(II) complex (1) and a robust laccase within cavities of a silica foam to favor veratryl alcohol oxidation. We performed the grafting of 1 at a unique surface located lysine of two laccase variants, either at closed (1⊂UNIK157) or opposite position (1⊂UNIK71) of the enzyme oxidation site. After immobilization into the cavities of silica monoliths bearing hierarchical porosity, we show that catalytic activity is dependent on the orientation and loading of each hybrid, 1⊂UNIK157 being twice as active than 1⊂UNIK71 (203 TON vs 100 TON) when operating under continuous flow. These systems can be reused 5 times, with an operational activity remaining as high as 40 %. We show that the synergy between 1 and laccase can be tuned within the foam. This work is a proof of concept for controlling the organization of a heterogeneous hybrid catalyst using a Pd/laccase/silica foam.