Yanbin Du
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yanbin Du has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
Qiang Liang
10 shared publicationsJian Tu
9 shared publicationsGuohua He
8 shared publicationsYunchuan Peng
7 shared publicationsHongxi Chen
Chongqing Key Laboratory of Green Design and Manufacturing of Intelligent Equipment, Chongqing Technology and Business University, Chongqing 400067, P. R. China
6 shared publicationsWensheng Ma
6 shared publications
Latest Publications
- 14 November 2026
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
MOEDO-BASED MULTI-OBJECTIVE OPTIMIZATION OF LASER REMELTING FOR SURFACE ROUGHNESS, MICROHARDNESS, AND ENERGY CONSUMPTION
In the context of low-carbon and energy-efficient manufacturing, this study investigated laser remelting of 35CrMo/Fe45 cladding layers to improve surface quality and microhardness while reducing energy consumption. Laser power, scanning speed, and overlap ratio were selected as the main process parameters, while surface roughness, microhardness, and electrical energy consumption during laser-on processing were taken as the optimization objectives. Based on the experimental data obtained using an enhanced Latin hypercube sampling design, a surrogate model was constructed. The multi-objective exponential distribution optimizer (MOEDO) was then used to generate a Pareto-optimal solution set, from which CRITIC–TOPSIS selected the optimal process parameters. Relative to the as-clad condition, the surface roughness of the cladding layer decreased from 8.56[Formula: see text] [Formula: see text]m to 0.789[Formula: see text] [Formula: see text]m, while the microhardness increased from 536 HV0.5 to 625.3 HV0.5. Compared with the reference condition, the optimized process reduced surface roughness by 39.6%, increased microhardness by 31.5%, and reduced electrical energy consumption during laser-on processing by 55.7%. The proposed approach provides a practical basis for balancing surface-quality improvement, hardness enhancement, and energy saving in energy-efficient laser remelting of cladding layers.
- 14 November 2026
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
MOEDO-BASED MULTI-OBJECTIVE OPTIMIZATION OF LASER REMELTING FOR SURFACE ROUGHNESS, MICROHARDNESS, AND ENERGY CONSUMPTION
In the context of low-carbon and energy-efficient manufacturing, this study investigated laser remelting of 35CrMo/Fe45 cladding layers to improve surface quality and microhardness while reducing energy consumption. Laser power, scanning speed, and overlap ratio were selected as the main process parameters, while surface roughness, microhardness, and electrical energy consumption during laser-on processing were taken as the optimization objectives. Based on the experimental data obtained using an enhanced Latin hypercube sampling design, a surrogate model was constructed. The multi-objective exponential distribution optimizer (MOEDO) was then used to generate a Pareto-optimal solution set, from which CRITIC–TOPSIS selected the optimal process parameters. Relative to the as-clad condition, the surface roughness of the cladding layer decreased from 8.56[Formula: see text] [Formula: see text]m to 0.789[Formula: see text] [Formula: see text]m, while the microhardness increased from 536 HV0.5 to 625.3 HV0.5. Compared with the reference condition, the optimized process reduced surface roughness by 39.6%, increased microhardness by 31.5%, and reduced electrical energy consumption during laser-on processing by 55.7%. The proposed approach provides a practical basis for balancing surface-quality improvement, hardness enhancement, and energy saving in energy-efficient laser remelting of cladding layers.
- Open Access
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
Mo-regulated tribo-oxide stability and near-surface evolution in laser-clad AlCoCrFeNiMox high-entropy alloy coatings during high-temperature sliding
AlCoCrFeNiMox high-entropy alloy coatings with different Mo contents (x = 0, 0.05, 0.15, 0.25, and 0.35) were fabricated on 316L stainless steel by laser cladding to improve its high-temperature sliding wear resistance. The effects of Mo addition on phase constitution, lattice distortion, microstructure, and hardness were investigated, and the tribological behavior of the coatings was evaluated at 600 °C, with emphasis on tribo-oxide-layer stability and post-wear near-surface evolution. All coatings were mainly composed of disordered A2 and ordered B2 phases. Increasing Mo content caused a low-angle shift of the main diffraction peaks and an increase in lattice parameter, indicating enhanced lattice distortion. Accordingly, the coating hardness increased monotonically, reaching 652.30 HV0.5 for Mo0.35, approximately 230% higher than that of the 316L substrate. In contrast, wear resistance showed a non-monotonic dependence on Mo content. The Mo0.25 coating exhibited the lowest average coefficient of friction of 0.2241 and the lowest wear rate of 4.08 × 10-6 mm3·N-1·m-1, corresponding to a reduction of approximately 98.8% relative to the substrate. Its superior wear resistance was attributed to improved load-bearing capacity and the retention of a continuous, compact tribo-oxide layer during sliding. Excessive Mo addition, although further increasing hardness, intensified Fe–Cr–Mo redistribution near grain boundaries and was accompanied by more pronounced σ-phase-related diffraction signals in the post-wear near-surface region, thereby weakening tribo-oxide-layer stability. These results indicate that the high-temperature sliding wear resistance of laser-clad AlCoCrFeNiMox coatings is governed by the balance among Mo-induced strengthening, tribo-oxide-layer stability, and near-surface microstructural evolution.
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMo-regulated tribo-oxide stability and near-surface evolution in laser-clad AlCoCrFeNiMox high-entropy alloy coatings during high-temperature sliding
AlCoCrFeNiMox high-entropy alloy coatings with different Mo contents (x = 0, 0.05, 0.15, 0.25, and 0.35) were fabricated on 316L stainless steel by laser cladding to improve its high-temperature sliding wear resistance. The effects of Mo addition on phase constitution, lattice distortion, microstructure, and hardness were investigated, and the tribological behavior of the coatings was evaluated at 600 °C, with emphasis on tribo-oxide-layer stability and post-wear near-surface evolution. All coatings were mainly composed of disordered A2 and ordered B2 phases. Increasing Mo content caused a low-angle shift of the main diffraction peaks and an increase in lattice parameter, indicating enhanced lattice distortion. Accordingly, the coating hardness increased monotonically, reaching 652.30 HV0.5 for Mo0.35, approximately 230% higher than that of the 316L substrate. In contrast, wear resistance showed a non-monotonic dependence on Mo content. The Mo0.25 coating exhibited the lowest average coefficient of friction of 0.2241 and the lowest wear rate of 4.08 × 10-6 mm3·N-1·m-1, corresponding to a reduction of approximately 98.8% relative to the substrate. Its superior wear resistance was attributed to improved load-bearing capacity and the retention of a continuous, compact tribo-oxide layer during sliding. Excessive Mo addition, although further increasing hardness, intensified Fe–Cr–Mo redistribution near grain boundaries and was accompanied by more pronounced σ-phase-related diffraction signals in the post-wear near-surface region, thereby weakening tribo-oxide-layer stability. These results indicate that the high-temperature sliding wear resistance of laser-clad AlCoCrFeNiMox coatings is governed by the balance among Mo-induced strengthening, tribo-oxide-layer stability, and near-surface microstructural evolution.
- 9 May 2026
- Published by Elsevier in Optics & Laser Technology
- Vol. 203
Construction and optimization of interpretable models for QT500-7 laser hardening process parameters
- 9 May 2026
- Published by Elsevier in Optics & Laser Technology
- Vol. 203
Construction and optimization of interpretable models for QT500-7 laser hardening process parameters
- Open Access
- 27 April 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Nb content on microstructure and high-temperature wear mechanism of FeAlCoCrNiNbx coatings prepared by substrate dilution
Heavy-duty mechanical transmission components fabricated from 30CrMo steel are prone to thermal softening, oxidative wear, and surface spallation when operating above 600 °C, leading to a significant reduction in service life. To enhance hightemperature wear resistance, FeAlCoCrNiNbx (x = 0, 3, 6, and 9 at.%) multi-principal element alloy coatings were fabricated in situ on the 30CrMo substrate by Nb doping during laser cladding, exploiting the Fe dilution effect. The influence of Nb content on the coating microstructure, mechanical properties, and high-temperature wear behavior was systematically investigated. The results indicate that the coating hardness increases with Nb content, with the 9 at.% Nb coating achieving an average hardness of 720 HV0.2, approximately 2.7 times that of the substrate. High-temperature wear resistance initially increases and then decreases with Nb content. Moderate Nb doping induces the formation of a relatively dense oxide layer, reducing direct metallic contact between the coating and counter-ball, with the 6 at.% Nb coating exhibiting the lowest wear rate (1.01 × 10-6 mm3·N-1·m-1), representing a 94.4% reduction compared to the substrate. Excessive Nb (9 at.%) leads to the formation of a continuous, coarse, and brittle Laves phase network, which under cyclic frictional stress promotes crack initiation and oxide spallation, deteriorating high-temperature wear performance. These findings indicate that moderate Nb doping is critical for optimizing the hardness and high-temperature wear resistance of FeAlCoCrNi-based multi-principal element alloy coatings, providing a feasible strategy for designing high-temperature wear-resistant multi-principal element coatings via substrate Fe dilution-assisted laser cladding.
- 27 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Nb content on microstructure and high-temperature wear mechanism of FeAlCoCrNiNbx coatings prepared by substrate dilution
Heavy-duty mechanical transmission components fabricated from 30CrMo steel are prone to thermal softening, oxidative wear, and surface spallation when operating above 600 °C, leading to a significant reduction in service life. To enhance hightemperature wear resistance, FeAlCoCrNiNbx (x = 0, 3, 6, and 9 at.%) multi-principal element alloy coatings were fabricated in situ on the 30CrMo substrate by Nb doping during laser cladding, exploiting the Fe dilution effect. The influence of Nb content on the coating microstructure, mechanical properties, and high-temperature wear behavior was systematically investigated. The results indicate that the coating hardness increases with Nb content, with the 9 at.% Nb coating achieving an average hardness of 720 HV0.2, approximately 2.7 times that of the substrate. High-temperature wear resistance initially increases and then decreases with Nb content. Moderate Nb doping induces the formation of a relatively dense oxide layer, reducing direct metallic contact between the coating and counter-ball, with the 6 at.% Nb coating exhibiting the lowest wear rate (1.01 × 10-6 mm3·N-1·m-1), representing a 94.4% reduction compared to the substrate. Excessive Nb (9 at.%) leads to the formation of a continuous, coarse, and brittle Laves phase network, which under cyclic frictional stress promotes crack initiation and oxide spallation, deteriorating high-temperature wear performance. These findings indicate that moderate Nb doping is critical for optimizing the hardness and high-temperature wear resistance of FeAlCoCrNi-based multi-principal element alloy coatings, providing a feasible strategy for designing high-temperature wear-resistant multi-principal element coatings via substrate Fe dilution-assisted laser cladding.
- 23 April 2026
- Published by Wiley in Quality and Reliability Engineering International
- Vol. 42 (6) , 2989-3002
Research on a Comprehensive Reliability Analysis Method for Industrial Robots Based on an Improved FMEA Approach
This paper addresses the shortcomings of the traditional failure mode and effects analysis (FMEAs) method in the reliability analysis of industrial robots and proposes an improved comprehensive FMEA analysis method. Firstly, according to the failure characteristics of industrial robots, the new risk factors of control ( C ) and cost sensitivity ( E ) are introduced, and a six‐dimensional risk evaluation system covering severity ( S ), occurrence ( O ), detection ( D ), maintenance ( M ), C , and E is established, which enhances the applicability of the method. Secondly, during the analysis process, interval numbers are used to represent expert decision information, reducing the impact of uncertainty. These interval numbers are further transformed into cloud models to simultaneously handle the fuzziness and randomness in the evaluation. Finally, by calculating the cloud clustering coefficient between the risk priority number (RPN) value of the cloud model for each failure mode (FM) with the standard risk cloud model, a multidimensional and quantitative assessment of the comprehensive risk level is achieved. The proposed method improves the accuracy and practicality of risk level for FMs, providing effective support for the reliability analysis and maintenance decision‐making of industrial robots.
- 23 April 2026
- Published by Wiley in Quality and Reliability Engineering International
- Vol. 42 (6) , 2989-3002
Research on a Comprehensive Reliability Analysis Method for Industrial Robots Based on an Improved FMEA Approach
This paper addresses the shortcomings of the traditional failure mode and effects analysis (FMEAs) method in the reliability analysis of industrial robots and proposes an improved comprehensive FMEA analysis method. Firstly, according to the failure characteristics of industrial robots, the new risk factors of control ( C ) and cost sensitivity ( E ) are introduced, and a six‐dimensional risk evaluation system covering severity ( S ), occurrence ( O ), detection ( D ), maintenance ( M ), C , and E is established, which enhances the applicability of the method. Secondly, during the analysis process, interval numbers are used to represent expert decision information, reducing the impact of uncertainty. These interval numbers are further transformed into cloud models to simultaneously handle the fuzziness and randomness in the evaluation. Finally, by calculating the cloud clustering coefficient between the risk priority number (RPN) value of the cloud model for each failure mode (FM) with the standard risk cloud model, a multidimensional and quantitative assessment of the comprehensive risk level is achieved. The proposed method improves the accuracy and practicality of risk level for FMs, providing effective support for the reliability analysis and maintenance decision‐making of industrial robots.
- Open Access
- 23 September 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 1038-1052
A hybrid optimization method for determining laser cladding process parameters to control geometric morphology in CoCrFeNiMn high-entropy alloy
- 23 September 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 39, 1038-1052
Open AccessA hybrid optimization method for determining laser cladding process parameters to control geometric morphology in CoCrFeNiMn high-entropy alloy
- 30 August 2025
- Published by Wiley in Steel Research International
- Vol. 97 (2) , 1026-1040
Simulation and Optimization of Temperature Field for Laser‐Cladded CoCrFeNiMn High‐Entropy Alloy Coating on 316L Stainless Steel Surface Based on Newton–Raphson‐Based Optimization‐Extreme Learning Machine and Classification and Pareto Dominance‐Based Multiobjective Evolutionary Algorithm
A laser cladding heat source parameter optimization method based on the Newton–Raphson‐based optimization‐extreme learning machine (NRBO‐ELM) and classification and Pareto dominance‐based multiobjective evolutionary algorithm (CPS‐MOEA) frameworks is proposed to improve the simulation accuracy of the laser cladding temperature field for high‐entropy alloy powder. CoCrFeNiMn high‐entropy alloy coating is prepared on 316 L stainless steel surfaces by laser cladding technology. An L25(5 3 ) orthogonal test is designed, and the transient temperature field in the laser cladding process is simulated by ANSYS. A mapping model between heat source parameters and molten pool quality characteristics is established based on NRBO‐ELM. The heat source parameters are optimized via the CPS‐MOEA algorithm to generate the Pareto solution set. A comprehensive evaluation and decision‐making method based on weighted rank sum ratio is developed to rank the Pareto solution set and determine the optimal combination of heat source parameters. Results demonstrate the existence of a critical point near shape parameters b and c = 2.5 mm, where the material's low thermal conductivity coefficient, coupled with the nonuniform distribution of heat source energy, results in localized heat accumulation. The NRBO‐ELM mapping model accurately predicts the transient temperature field with less than 2% error. The optimized transient temperature field in laser cladding shows consistency with actual experimental measurements.
- 30 August 2025
- Published by Wiley in Steel Research International
- Vol. 97 (2) , 1026-1040
Simulation and Optimization of Temperature Field for Laser‐Cladded CoCrFeNiMn High‐Entropy Alloy Coating on 316L Stainless Steel Surface Based on Newton–Raphson‐Based Optimization‐Extreme Learning Machine and Classification and Pareto Dominance‐Based Multiobjective Evolutionary Algorithm
A laser cladding heat source parameter optimization method based on the Newton–Raphson‐based optimization‐extreme learning machine (NRBO‐ELM) and classification and Pareto dominance‐based multiobjective evolutionary algorithm (CPS‐MOEA) frameworks is proposed to improve the simulation accuracy of the laser cladding temperature field for high‐entropy alloy powder. CoCrFeNiMn high‐entropy alloy coating is prepared on 316 L stainless steel surfaces by laser cladding technology. An L25(5 3 ) orthogonal test is designed, and the transient temperature field in the laser cladding process is simulated by ANSYS. A mapping model between heat source parameters and molten pool quality characteristics is established based on NRBO‐ELM. The heat source parameters are optimized via the CPS‐MOEA algorithm to generate the Pareto solution set. A comprehensive evaluation and decision‐making method based on weighted rank sum ratio is developed to rank the Pareto solution set and determine the optimal combination of heat source parameters. Results demonstrate the existence of a critical point near shape parameters b and c = 2.5 mm, where the material's low thermal conductivity coefficient, coupled with the nonuniform distribution of heat source energy, results in localized heat accumulation. The NRBO‐ELM mapping model accurately predicts the transient temperature field with less than 2% error. The optimized transient temperature field in laser cladding shows consistency with actual experimental measurements.
- 9 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (22) , 26285-26297
Effect of WC Content on the Wear Resistance of WC/Ni60 Composite Coatings on 35CrMoV Steel by Laser Cladding
- 9 May 2025
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (22) , 26285-26297
Effect of WC Content on the Wear Resistance of WC/Ni60 Composite Coatings on 35CrMoV Steel by Laser Cladding