YMYurii Maksymiuk

Yurii Maksymiuk

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yurii Maksymiuk has a total of 59 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Assessment of the effect of the fluctuating component of wind pressure on a lattice telecommunication tower

    by Yurii Maksymiuk, Yevhen Tsyupyn, Olha Bashynska, Andrii Kozak

    The paper presents a calculation methodology for accounting for the fluctuating component of wind loading in the analysis of a spatial lattice telecommunication tower 50 m high, designed according to a modular concept (2.0 m vertical module) with plan-dimension changes along the height. Unlike the standard approach, where the dynamic coefficient is taken as an input multiplier, a methodology based on the peak response parameter is proposed. In this methodology, the equivalent dynamic coefficient is determined by the criterion of the structure’s peak response (top displacement, base bending moment, or critical axial force), and the distribution of equivalent nodal forces is formed so as to ensure equality of the generalized modal force in the first vibration mode. The matrix form of the equations of motion is given in full as , with derivation of the element stiffness and mass matrices of a spatial truss element and rules for assembling the global matrices. An algorithm is proposed for piecewise formation of the equivalent wind load over the height intervals 0–32, 32–34, 34–44, 44–46, and 46–50 m, converting pressure to forces through the effective projected area of the lattice. The methodology provides a physically justified consideration of the fluctuating component without direct time-history simulation of the wind process and improves the reproducibility of calculation results. In addition, the choice of the first mode as dominant for the along-wind response is substantiated, and procedural checks of load consistency are provided through equality of the generalized modal force. It is shown that the piecewise discretization enables correct consideration of structural transitions and differences in «wind-exposed area» along the height, while the use of the effective projected area reduces subjectivity when modeling permeable lattice systems. A control criterion is proposed: and , which guarantees convergence with respect to the selected response quantity.

  • Open Access

    Сomparative analysis of methods for determining the parameters of small-sized vibration installations

    by Yurii Maksymiuk, Mykola Kuzminets, Artur Onyshchenko, Ivan Martyniuk, Oleksandr Maksymiuk

    The article discusses modern approaches to determining the main parameters of small-sized vibrating pads, which are widely used in the construction industry for compaction of concrete mixtures and the formation of products with specified physical and mechanical properties. The relevance of the study is due to the need to increase the efficiency of vibration equipment while reducing energy consumption, material consumption and dimensions of installations. The main attention is paid to the analysis of existing methods for calculating the dynamic characteristics of vibration sites, in particular, the determination of the amplitude of vibrations, the frequency of excitation, accelerations of the working platform and the parameters of vibration exciters. Analytical, empirical and numerical approaches to modeling oscillatory processes, including the application of methods of the theory of oscillations and finite elements, are considered. It has been established that traditional analytical dependencies do not always take into account the influence of design features and real operating conditions, which can lead to deviations between the calculated and experimental data. The paper conducts a comparative analysis of various calculation methods, identifies their advantages and limitations in terms of accuracy, labor intensity and the possibility of practical application. Particular attention is paid to the influence of the loading mass, the rigidity of elastic elements and the parameters of the excitatory force on the efficiency of the vibrating platform. It is shown that the most promising are combined approaches that combine analytical calculations with numerical modeling and experimental verification of results. The results obtained can be used in the design and modernization of small-sized vibration units, as well as for optimizing their operating modes, taking into account specific technological conditions. The practical significance of the study is to improve the quality of compaction of concrete mixtures, reduce energy costs and ensure the reliability of equipment operation. Thus, the analysis allows us to form reasonable recommendations for the choice of effective methods for calculating the parameters of small-sized vibration platforms and determines the directions of further scientific research in this area.

  • Open Access

    Conditions for implementing tutorial technology in teaching construction mechanics

    by Kostiantyn Pochka, Yurii Maksymiuk, Yurii Krasylnyk, Halyna Korchova, Mykola Rudenko

    The conditions for implementing tutoring technology in teaching construction mechanics have been established, covering pedagogical, organisational, material, technical and psychological aspects of the educational process. Pedagogical conditions include training teachers as tutors, developing methodological strategies for individual and group support of students, and creating teaching and methodological support that promotes the development of competencies of future professionals. Organisational conditions include optimising the structure of the educational process, determining the mode of interaction between the teacher as a tutor and students, planning training modules, and coordinating work between departments and laboratories. Material and technical conditions provide access to modern teaching aids, digital platforms, laboratory equipment and electronic resources, enabling personalised learning and active practical activities. Psychological conditions consist of creating an atmosphere of trust, motivation, support for independence and responsibility among students, which shapes their readiness for professional development and self-improvement. The structural components of the tutorial technology for teaching construction mechanics are revealed, among which the target, content, technological, activity and result blocks are distinguished. The target component determines the directions of training and program learning outcomes, while the content component shapes the content of the educational process in accordance with standards and competency requirements. The technological component includes methods, techniques and tools of tutoring support, the activity component involves specific activities of students and tutors, and the result component evaluates the effectiveness of learning and the achievement of educational goals. The key determinants of the effectiveness of tutoring support for students are substantiated, among which the level of pedagogical competence of the tutor, the degree of individualisation of learning, the motivational potential of students and the integration of digital learning technologies are highlighted. The main approaches to personalising learning are identified, which involve building an individual educational trajectory, adapting learning material to the needs and abilities of students, systematic assessment of results, and correction of the educational process.

  • Open Access

    THE USE OF ADDITIVE TECHNOLOGIES IN THE CONSTRUCTION OF HIGH-RISE STRUCTURES

    by М. І. Барбаш, Yu. Maksymiuk, K. Dmytriiev, Ю. В. Максим’юк, К. В. Дмитрієв

    Additive manufacturing is emerging as a transformative approach for the rapid, resource-efficient erection of high-rise concrete structures. Conventional formwork-based methods incur substantial material waste (up to 60 %), prolonged construction cycles and heavy labor demands. This study evaluates extrusion-based 3D concrete printing (3DCP) and its integration with advanced simulation, robotics and inline quality control to overcome these constraints. First, the extrusion process is optimized by balancing pumpability and buildability: mixes with slump flows of 190–200 mm and controlled thixotropy ensure stable filament deposition at layer thicknesses of 8–12 mm, while compressed-air or screw-driven extruders maintain consistent flow rates and prevent air entrapment. Time-dependent rheology is managed through inline monitoring of shear strength, extending workable “open time” to 20–25 minutes under field conditions. Material modifications, including 0.5 % polypropylene fibers and 10 % fly-ash substitution, improve interlayer adhesion by 15 % and reduce micro-cracking, respectively. Mechanical behavior of printed elements is predicted using nonlinear finite-element models that incorporate time-evolving stiffness from 1 kPa up to 100 MPa within the first 24 hours. Calibration against laboratory shear-vanes and compression tests yields accurate forecasts of deformation (±5 % error) and stress distribution, supporting design of multi-story wall modules. Cooperative robotics, coordinated through BIM, further enhance precision: three-robot setups reduce peak bending moments by 67 %, support forces by up to 37 %, and positional deviations below ±3 mm, enabling the fabrication of complex vaults and free-form façades without temporary shoring. Economic analysis demonstrates that 3DCP can reduce material costs by 78 % and labor inputs by 60 %, achieving print rates up to 12 m³/h and producing a standard 3 × 3 m module in under 30 hours. When coupled with modular factory production of network-integrated panels, onsite assembly time drops from days to hours. Government incentives and dedicated research grants have accelerated pilot installations, yet the absence of unified standards for strength (≥ 30 MPa at 24 hours) and geometric tolerances (±5 mm) remains a critical barrier. To scale additive methods in vertical construction, it is vital to establish comprehensive process certifications, develop cementitious mixes with extended workability windows, refine multi-agent print planning algorithms, and conduct large-scale field trials. These steps will embed 3D concrete printing within building codes, ensuring its reliability, safety and widespread adoption in tomorrow’s urban skylines.

  • Open Access

    Calculation of the t-shaped shank of the steam turbine rotor blade

    by Yurii Maksymiuk, Ivan Martyniuk, Andriy Andrusyak, Oleksandr Kozak

    The broad possibilities of the developed approach [8, 9, 11, 12] are illustrated by the solution of a new practically important task related to specific design developments. The most important load-bearing elements of the rotors of steam turbines are the blade shanks. This paper presents the calculation of the T-shaped shank, which is affected by the forces caused by the rotation of the rotor. They consist of the surface load blade distributed over the area of the root section of the blade and mass forces distributed over the volume of the shank. but along some of its central parts. This leads to an uneven distribution of contact forces along the axis along the shank. The results of the calculation allow us to draw the following conclusions that in the case of a uniform load, the determination of stresses can be carried out within the framework of a flat setting, since this leads to a relatively small (five, eight percent) error compared to the spatial setting. Taking into account the uneven nature of the load distribution along the length of the shelf allows you to significantly clarify the level of maximum stresses in comparison with a flat problem. Thus, the value of the intensity of tangential stresses increased by more than thirty percent and exceeded the yield strength of the material. The results of the calculation of the shank beyond the elastic properties of the material are presented in this work and reflect the development of the zone of plastic deformations in the plane Z3'=0. By studying the influence of the geometric parameters of the shank, it was found that a decrease in the level of plastic deformations can be achieved by simultaneously increasingthe radiusthe gap and the width of the shelf.

  • Open Access

    MODELING OF DYNAMIC SYSTEMS IN THE DESIGN OF MECHANICAL STRUCTURES FOR INDUSTRY

    by Y. Maksymiuk, O. Avdiichuk, D. Lukianchuk

    Modeling dynamic systems in the design of mechanical structures is a crucial area of modern engineering as it ensures increased efficiency, reliability, and resilience of equipment under changing operational conditions. The relevance of this study is driven by the necessity to develop high-tech solutions that address contemporary industrial challenges, particularly through the integration of adaptive and parametric approaches to design. The growing demands for energy efficiency, durability, and cost reduction in maintenance highlight the importance of utilizing innovative materials and modern engineering tools. The aim of this study is to develop approaches for modeling dynamic systems using integrated parametric and adaptive methods to enhance the efficiency and resilience of mechanical structures under variable operational conditions. To achieve this aim, the study employed analytical reviews of contemporary approaches to dynamic system design, modeling of their behavior under changing loads, and comparative analysis of methods for integrating adaptive solutions into mechanical structures. The study analyzed modern methods for modeling dynamic systems and assessed their practical efficiency in the industry. A model was developed to integrate parametric and adaptive approaches, enabling the optimization of structures while considering variable technological conditions. Key challenges were identified, including the high cost of implementation, technical limitations of software, and insufficient integration of innovations into traditional manufacturing processes. The conclusions emphasize that the use of adaptive solutions and advanced materials significantly reduces vibrations, increases structural durability, and decreases maintenance costs. Recommendations include implementing sensor networks and digital twins for real-time equipment monitoring, as well as improving optimization models. The prospects for further research involve developing new algorithms to enhance energy efficiency, integrating adaptive systems into industrial equipment, and creating innovative methods for predicting the technical condition of structures. This will ensure high industrial competitiveness in a dynamically changing market environment.

  • Features of the Dynamic Interaction Between the Elastically Deformed Working Body of a Ripper-Pick and the Soil

    by Kostiantyn Pochka, Mykola Prystailo, Maksym Delembovskyi, Maksym Balaka, Yurii Maksymiuk, Andrii Polishchuk


  • Open Access

    Technical aspects of ensuring seismic stability of modern structures

    by Yurii Maksymiuk, Oleksandr Avdiichuk, Dmytro Lukianchuk

    The article examines an important area of civil engineering that is becoming increasingly significant in the context of growing urbanization and the increasing frequency of seismic events worldwide. As populations concentrate in earthquake-prone regions, ensuring the structural integrity of buildings and infrastructure becomes a primary task for architects, engineers, and urban planners. The relevance of this topic is determined by the devastating impact of earthquakes on human life, economic stability, and environmental integrity, making the development of reliable methods and technologies to improve seismic resilience essential. The aim of the research is to explore and analyze advanced engineering solutions, in particular innovative materials, structural systems and seismic isolation technologies, to improve the seismic stability of modern structures while addressing practical implementation challenges. The article presents a comprehensive analysis of current technical solutions used in the design and construction of earthquake-resistant structures. It discusses advancements in materials science, innovative architectural designs, and the integration of modern engineering technologies such as base isolation, energy dissipation systems, and reinforced concrete technologies. The role of computer programs and modeling in predicting seismic responses and optimizing structural performance under dynamic loads is also highlighted. The results show that the use of these modern methods significantly enhances the ability of structures to withstand seismic forces, thereby reducing the potential for catastrophic failure. Thus, the study emphasizes the necessity for continuous innovation and adaptation in seismic design practices. The article underscores the need for a multidisciplinary approach that incorporates knowledge from geotechnical engineering, materials science, and architecture to create resilient urban environments. Furthermore, it advocates for updating building codes and regulations to reflect the latest research findings and technological advancements. The article confirms that, despite significant progress in ensuring the seismic stability of modern structures, ongoing research and collaborative efforts are crucial for addressing the evolving challenges posed by earthquakes.

  • Open Access

    Development and computer testing of equipment for cutting soils with spatially oriented knives of a bulldozer blade

    by Yurii Maksymiuk, Volodymyr Rashkivskyi, Mykola Prystailo, Bohdan Fedyshyn

    The paper uses approaches to the creation and computer testing of a model of an experimental installation for cutting soil with spatially oriented working bodies of earthmoving machines used on construction sites. Today, there is a need for the efficient performance of construction work related to the operation of construction machinery with blade equipment. This, in turn, poses the task of determining the productivity of mechanized earthworks in various working environments. The main method of mechanical soil development is cutting. The main geometric conditions are the position of the cutting wedge edge relative to the cutting direction and the surface of the massif, the contour of the cutting edge, the contour and number of working surfaces of the cutting wedge, the number of so-called side cutting surfaces and the so-called blocked cutting surfaces. The peculiarity of the digging process is that its power and energy indicators depend on the kinematic conditions and geometric parameters - thickness, width and cut area, as well as on the angles of orientation of the working body in space. The creation of such a computer model of the experimental setup is due to the need for continuous improvement of existing equipment and the creation of new equipment to meet existing needs. The model of the experimental setup was created in accordance with the working hypothesis, where the movement of the spatially oriented knife occurs perpendicular to the movement of the blade equipment, at different ratios of the speed of the blade and the movement of the knife, which creates a simple interaction with the working environment, and the deviation of the application of the full cutting force by an angle α. According to the working hypothesis, depending on the plan of movement of the spatially oriented knife, its geometric interaction with the working environment changes and the cutting force changes accordingly. The necessity to create more productive and efficient earthmoving equipment requires the use of modern design solutions. Using the calculations of soil cutting by spatially oriented earthmoving tools in the form of a dihedral blade of dump equipment, a computer study of stress equivalents, linear displacement, yield strength factor, tensile strength factor, and loss of stability factor was carried out. The results are summarized in the form of tabular data and graphical display.


  • Open Access

    Analysis of the stress-strain state of the rotary device fastening part by the semi-analytical finite element method

    by Yurii Maksymiuk, Oleksii Shkryl, Ivan Martyniuk, Andrii Kozak, Oleksandr Maksymiuk

    The possibilities of the numerical apparatus developed on the basis of the semi-analytical finite element method are shown on the example of solving a specific problem. In the areas of maximum values, the parameters of the stress-strain state of the re-device fastening part were compared. It is worth noting the relatively complex configuration of the cross-section of the object, which led to a thorough study of the principles of constructing a grid area. The surface of interaction between the axis and the hull was modeled by a fairly thin layer of elements in relation to their thickness, which absorb only normal stresses. Analysis of the stress-strain state of the rotary device fastening part should be carried out from the standpoint of a spatial problem. Moreover, according to the results of the elastic calculation, the transition section between the body and the base plate turned out to be more loaded compared to the zone of contact interaction between the body and the axle. The data of the calculation performed in the elastic-plastic formulation made it possible to clarify the idea of the operating conditions of individual sections of the object and to draw a conclusion about the uniformity of the hull. The carried out studies confidently demonstrated the wide possibilities of the developed approach in solving new, practically important problems of elastic deformation of prismatic bodies of complex shape in the spatial formulation of new ones. To substantiate the reliability of the results of the calculation of the elements under consideration, a sequential increase in the number of FE in the cross-section and the number of retained terms of the decomposition along the length of the body, as well as an increase in the accuracy of solving systems of equations, are given. In addition, an assessment of the satisfaction of natural boundary conditions on the surface of the body and the conditions of equilibrium in the integral sense is given according to the characteristic sections within the region, which showed their fairly good performance. New data on the regularities of behavior of critical structures in the process of loading, due to the consideration of their physical and geometric parameters, have been obtained.