Vicente Lopes Junior
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Vicente Lopes Junior has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Samuel da Silva
Department of Mechanical Engineering, Universidade Estadual Paulista (UNESP), Ilha Solteira, Brazil
9 shared publications - Gilberto Pechoto de Melo
Unesp - Ilha Solteira
3 shared publications Michael J. Brennan
Institute of Sound and Vibration Research, University of Southampton, Southampton, UK
3 shared publications- Michael John Brennan
São Paulo State University (UNESP)
3 shared publications Clayton Rodrigo Marqui
Embraer
2 shared publications- Gustavo Luiz Chagas Manhães de Abreu
Universidade Estadual Paulista - UNESP, FEIS, Dep. de Engenharia Mecânica, Ilha Solteira-SP
2 shared publications
Latest Publications
- 4 June 2016
- Published by Springer Nature
- p. 1-3
Introduction
- 4 June 2016
- Published by Springer Nature
- p. 135-154
Piezoelectric Materials
- Open Access
- 4 April 2014
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 37 (2) , 441-450
Active modal damping control of a smart truss structure using a self-organizing fuzzy controller
- 4 April 2014
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 37 (2) , 441-450
Open AccessActive modal damping control of a smart truss structure using a self-organizing fuzzy controller
- 1 February 2014
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 333 (5) , 1331-1343
An investigation into the simultaneous use of a resonator as an energy harvester and a vibration absorber
- 1 February 2014
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 333 (5) , 1331-1343
An investigation into the simultaneous use of a resonator as an energy harvester and a vibration absorber
- 31 August 2013
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 36 (3) , 523-532
Identification of nonlinear structures using discrete-time Volterra series
- 31 August 2013
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 36 (3) , 523-532
Identification of nonlinear structures using discrete-time Volterra series
- 26 March 2013
- Published by Springer Nature in Journal of Control, Automation and Electrical Systems
- Vol. 24 (1-2) , 54-69
Fuzzy Control Embedded in Microcontroller and Applied to an Experimental Apparatus Using Magnetorheological Fluid Damper
- 26 March 2013
- Published by Springer Nature in Journal of Control, Automation and Electrical Systems
- Vol. 24 (1-2) , 54-69
Fuzzy Control Embedded in Microcontroller and Applied to an Experimental Apparatus Using Magnetorheological Fluid Damper
- Open Access
- 1 January 2012
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 34 (spe) , 386-392
System identification and active vibration control of a flexible structure
- 1 January 2012
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 34 (spe) , 386-392
Open AccessSystem identification and active vibration control of a flexible structure
- 21 July 2011
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 22 (14) , 1581-1594
Modeling and Experimental Aspects of Self-healing Bolted Joint through Shape Memory Alloy Actuators
Bolted joints are a form of mechanical coupling largely used in machinery due to their reliability and low cost. Failure of bolted joints can lead to catastrophic events, such as leaking, train derailments, aircraft crashes, etc. Most of these failures occur due to the reduction of the pre-load, induced by mechanical vibration or human errors in the assembly or maintenance process. This article investigates the application of shape memory alloy (SMA) washers as an actuator to increase the pre-load on loosened bolted joints. The application of SMA washer follows a structural health monitoring procedure to identify a damage (reduction in pre-load) occurrence. In this article, a thermo-mechanical model is presented to predict the final pre-load achieved using this kind of actuator, based on the heat input and SMA washer dimension. This model extends and improves on the previous model of Ghorashi and Inman [2004, “Shape Memory Alloy in Tension and Compression and its Application as Clamping Force Actuator in a Bolted Joint: Part 2 – Modeling,” J. Intell. Mater. Syst. Struct., 15:589–600], by eliminating the pre-load term related to nut turning making the system more practical. This complete model is a powerful but complex tool to be used by designers. A novel modeling approach for self-healing bolted joints based on curve fitting of experimental data is presented. The article concludes with an experimental application that leads to a change in joint assembly to increase the system reliability, by removing the ceramic washer component. Further research topics are also suggested.
- 21 July 2011
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
- Vol. 22 (14) , 1581-1594
Modeling and Experimental Aspects of Self-healing Bolted Joint through Shape Memory Alloy Actuators
Bolted joints are a form of mechanical coupling largely used in machinery due to their reliability and low cost. Failure of bolted joints can lead to catastrophic events, such as leaking, train derailments, aircraft crashes, etc. Most of these failures occur due to the reduction of the pre-load, induced by mechanical vibration or human errors in the assembly or maintenance process. This article investigates the application of shape memory alloy (SMA) washers as an actuator to increase the pre-load on loosened bolted joints. The application of SMA washer follows a structural health monitoring procedure to identify a damage (reduction in pre-load) occurrence. In this article, a thermo-mechanical model is presented to predict the final pre-load achieved using this kind of actuator, based on the heat input and SMA washer dimension. This model extends and improves on the previous model of Ghorashi and Inman [2004, “Shape Memory Alloy in Tension and Compression and its Application as Clamping Force Actuator in a Bolted Joint: Part 2 – Modeling,” J. Intell. Mater. Syst. Struct., 15:589–600], by eliminating the pre-load term related to nut turning making the system more practical. This complete model is a powerful but complex tool to be used by designers. A novel modeling approach for self-healing bolted joints based on curve fitting of experimental data is presented. The article concludes with an experimental application that leads to a change in joint assembly to increase the system reliability, by removing the ceramic washer component. Further research topics are also suggested.
- 12 May 2011
- Published by Springer Nature
- p. 875-882
Adaptive Filter Feature Identification for Structural Health Monitoring in Aeronautical Panel
- 12 May 2011
- Published by Springer Nature
- p. 875-882
Adaptive Filter Feature Identification for Structural Health Monitoring in Aeronautical Panel
- 27 August 2010
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 10 (5) , 481-489
Adaptive filter feature identification for structural health monitoring in an aeronautical panel
This article presents an approach to structural health monitoring (SHM) using adaptive filters. The experimental signals from different structural conditions provided by piezoelectric actuators/sensors bonded in the test structure are modeled by a discrete-time recursive least square (RLS) filter. The biggest advantage of using a RLS filter is the clear possibility to perform an online SHM procedure because the identification is also valid for nonstationary linear systems. An online damage-sensitive index feature is computed based on portions of the autoregressive coefficients normalized by the square root of the sum of the squares. The proposed method is then used in a laboratory test involving an aeronautical panel coupled with piezoelectric sensors/actuators (PZTs) in different positions. To test this hypothesis, the t-test is used to obtain the damage decision. The proposed algorithm was able to identify and localize damages in the structure. The article concludes by exploring the applicability and drawbacks of the method and proposes some implementation suggestions.
- 27 August 2010
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 10 (5) , 481-489
Adaptive filter feature identification for structural health monitoring in an aeronautical panel
This article presents an approach to structural health monitoring (SHM) using adaptive filters. The experimental signals from different structural conditions provided by piezoelectric actuators/sensors bonded in the test structure are modeled by a discrete-time recursive least square (RLS) filter. The biggest advantage of using a RLS filter is the clear possibility to perform an online SHM procedure because the identification is also valid for nonstationary linear systems. An online damage-sensitive index feature is computed based on portions of the autoregressive coefficients normalized by the square root of the sum of the squares. The proposed method is then used in a laboratory test involving an aeronautical panel coupled with piezoelectric sensors/actuators (PZTs) in different positions. To test this hypothesis, the t-test is used to obtain the damage decision. The proposed algorithm was able to identify and localize damages in the structure. The article concludes by exploring the applicability and drawbacks of the method and proposes some implementation suggestions.