Mohamed A. K. Othman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mohamed A. K. Othman has a total of 95 co-authors. Here are the top co-authors by number of shared publications:
- Filippo Capolino
University of California
17 shared publications - Emilio Alessandro Nanni
SLAC National Accelerator Laboratory, Stanford University, Menlo Park, USA
10 shared publications - Alexander Figotin
Department of Mathematics, University of California , Irvine, California 92697
6 shared publications - Matthias. C. Hoffmann
Linac Coherent Light Source, SLAC National Accelerator Laboratory, Menlo Park, USA
6 shared publications X. J. Wang
SLAC National Accelerator Laboratory, Stanford University, Menlo Park, CA
6 shared publications- Annika E. Gabriel
University of California Santa Cruz
5 shared publications
Latest Publications
- Open Access
- 17 September 2026
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 29  (9) , 093801
Development of ultrahigh power compact x-band pulse compressor
We demonstrate a new 11.424 GHz SLED-type rf pulse compressor for powering high-gradient x-band photoinjectors with pulse lengths around 20 ns. rf pulse compression provides a practical path to higher peak power at the cost of pulse length for various applications such as rf deflectors for electron beam diagnostics on free-electron lasers. Our new compact pulse compressor uses spherical cavities supporting axially symmetric TE modes which have minimal electric fields on the cavity surfaces, intended to improve high-power robustness as compared to existing compact spherical SLEDs which use a TE dipole mode. We present the design of this pulse compressor composed of two spherical cavities and a waveguide hybrid. The two cavities and hybrid have TE 01 circular waveguide ports. This pulse compressor was built and high power tested at SLAC. These tests demonstrated a peak power of 317 MW by compressing 52 MW, 1 μ s pulses generated by a SLAC XL-4 klystron representing, to our knowledge, the highest peak power achieved from a single-stage compact SLED rf pulse compressor at x-band. The full width at half maximum of this compressed pulse was ( 27.1 ± 1.1 ) ns . We conjecture that this development demonstrates a viable route to reaching the high-gradient, short pulse regime for accelerating structures and rf photoinjectors.
- 17 September 2026
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 29  (9) , 093801
Open AccessDevelopment of ultrahigh power compact x-band pulse compressor
We demonstrate a new 11.424 GHz SLED-type rf pulse compressor for powering high-gradient x-band photoinjectors with pulse lengths around 20 ns. rf pulse compression provides a practical path to higher peak power at the cost of pulse length for various applications such as rf deflectors for electron beam diagnostics on free-electron lasers. Our new compact pulse compressor uses spherical cavities supporting axially symmetric TE modes which have minimal electric fields on the cavity surfaces, intended to improve high-power robustness as compared to existing compact spherical SLEDs which use a TE dipole mode. We present the design of this pulse compressor composed of two spherical cavities and a waveguide hybrid. The two cavities and hybrid have TE 01 circular waveguide ports. This pulse compressor was built and high power tested at SLAC. These tests demonstrated a peak power of 317 MW by compressing 52 MW, 1 μ s pulses generated by a SLAC XL-4 klystron representing, to our knowledge, the highest peak power achieved from a single-stage compact SLED rf pulse compressor at x-band. The full width at half maximum of this compressed pulse was ( 27.1 ± 1.1 ) ns . We conjecture that this development demonstrates a viable route to reaching the high-gradient, short pulse regime for accelerating structures and rf photoinjectors.
- 21 August 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33  (17) , 37084-37094
Three-dimensional reconstruction of THz near-fields from a LiNbO3 optical rectification source
Terahertz (THz) generation by optical rectification in LiNbO3 (LN) is a widely used technique for generating intense THz radiation. The spatiotemporal characterization of THz pulses from these sources is currently limited to far-field methods. While simulations of tilted pulse front THz generation have been published, little work has been done to measure the near-field properties of the THz source. A better understanding of the THz near-field properties will improve optimization of THz generation efficiency, transport, and coupling. We demonstrate a technique for quantitative spatiotemporal characterization of single-cycle strong-field THz pulses with 2-D near-field electro-optic imaging. We have reconstructed the full temporal 3D THz near-field and shown how the phase front can be tailored by controlling the incident pump pulse.
- 21 August 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33  (17) , 37084-37094
Three-dimensional reconstruction of THz near-fields from a LiNbO3 optical rectification source
Terahertz (THz) generation by optical rectification in LiNbO3 (LN) is a widely used technique for generating intense THz radiation. The spatiotemporal characterization of THz pulses from these sources is currently limited to far-field methods. While simulations of tilted pulse front THz generation have been published, little work has been done to measure the near-field properties of the THz source. A better understanding of the THz near-field properties will improve optimization of THz generation efficiency, transport, and coupling. We demonstrate a technique for quantitative spatiotemporal characterization of single-cycle strong-field THz pulses with 2-D near-field electro-optic imaging. We have reconstructed the full temporal 3D THz near-field and shown how the phase front can be tailored by controlling the incident pump pulse.
- Open Access
- 1 March 2024
- Published by AIP Publishing in Structural Dynamics
- Vol. 11  (2) , 024311
Improved temporal resolution in ultrafast electron diffraction measurements through THz compression and time-stamping
We present an experimental demonstration of ultrafast electron diffraction (UED) with THz-driven electron bunch compression and time-stamping that enables UED probes with improved temporal resolution. Through THz-driven longitudinal bunch compression, a compression factor of approximately four is achieved. Moreover, the time-of-arrival jitter between the compressed electron bunch and a pump laser pulse is suppressed by a factor of three. Simultaneously, the THz interaction imparts a transverse spatiotemporal correlation on the electron distribution, which we utilize to further enhance the precision of time-resolved UED measurements. We use this technique to probe single-crystal gold nanofilms and reveal transient oscillations in the THz near fields with a temporal resolution down to 50 fs. These oscillations were previously beyond reach in the absence of THz compression and time-stamping.
- 1 March 2024
- Published by AIP Publishing in Structural Dynamics
- Vol. 11  (2) , 024311
Open AccessImproved temporal resolution in ultrafast electron diffraction measurements through THz compression and time-stamping
We present an experimental demonstration of ultrafast electron diffraction (UED) with THz-driven electron bunch compression and time-stamping that enables UED probes with improved temporal resolution. Through THz-driven longitudinal bunch compression, a compression factor of approximately four is achieved. Moreover, the time-of-arrival jitter between the compressed electron bunch and a pump laser pulse is suppressed by a factor of three. Simultaneously, the THz interaction imparts a transverse spatiotemporal correlation on the electron distribution, which we utilize to further enhance the precision of time-resolved UED measurements. We use this technique to probe single-crystal gold nanofilms and reveal transient oscillations in the THz near fields with a temporal resolution down to 50 fs. These oscillations were previously beyond reach in the absence of THz compression and time-stamping.
- 3 April 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122  (14)
Measurement of femtosecond dynamics of ultrafast electron beams through terahertz compression and time-stamping
Visualizing ultrafast dynamics at the atomic scale requires time-resolved characterization with femtosecond temporal resolution. For fully relativistic electron bunch probes, existing techniques for single-shot ultrafast electron diffraction (UED) are limited by the achievable electron probe bunch length, charge, and timing jitter. We present the first experimental demonstration of dual-fed THz-driven compression and time-stamping that enables electron probes with improved temporal resolution. This technique utilizes two counter-propagating quasi-single-cycle THz pulses generated from two OH-1 organic crystals coupled into an optimized THz compressor structure. We demonstrate electron bunch compression and time-of-arrival jitter suppression by a factor of 3 paving the way toward unique opportunities for UED time-resolved measurements.
- 3 April 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122  (14)
Measurement of femtosecond dynamics of ultrafast electron beams through terahertz compression and time-stamping
Visualizing ultrafast dynamics at the atomic scale requires time-resolved characterization with femtosecond temporal resolution. For fully relativistic electron bunch probes, existing techniques for single-shot ultrafast electron diffraction (UED) are limited by the achievable electron probe bunch length, charge, and timing jitter. We present the first experimental demonstration of dual-fed THz-driven compression and time-stamping that enables electron probes with improved temporal resolution. This technique utilizes two counter-propagating quasi-single-cycle THz pulses generated from two OH-1 organic crystals coupled into an optimized THz compressor structure. We demonstrate electron bunch compression and time-of-arrival jitter suppression by a factor of 3 paving the way toward unique opportunities for UED time-resolved measurements.
- Open Access
- 14 December 2022
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 25  (12) , 121301
Design, fabrication, and tuning of a THz-driven electron gun
We present the design, fabrication, and cold testing of a THz-driven field emission electron gun. The gun is designed as a two-cell standing-wave structure with a copper tip inserted halfway into the first cell that serves as the field emission source. It is powered by a 110 GHz gyrotron and is expected to produce 51 fC, 360 keV electron bunches with an input power of 500 kW. Several gun structures were fabricated using a high precision diamond turned mandrel and copper electroforming. The frequencies of the cavity resonances were mechanically tuned using azimuthal compression.
- 14 December 2022
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 25  (12) , 121301
Open AccessDesign, fabrication, and tuning of a THz-driven electron gun
We present the design, fabrication, and cold testing of a THz-driven field emission electron gun. The gun is designed as a two-cell standing-wave structure with a copper tip inserted halfway into the first cell that serves as the field emission source. It is powered by a 110 GHz gyrotron and is expected to produce 51 fC, 360 keV electron bunches with an input power of 500 kW. Several gun structures were fabricated using a high precision diamond turned mandrel and copper electroforming. The frequencies of the cavity resonances were mechanically tuned using azimuthal compression.
- Open Access
- 22 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Temporal and Spatial Characterization of Ultrafast Terahertz Near-Fields for Particle Acceleration
Terahertz generation by optical rectification in LiNbO 3 using the tilted pulse front method is a powerful technique that is routinely used to generate THz pulses with energies in the tens of micro-joules and field strengths above 1 MV/cm. THz-frequency accelerating structures that utilize these fields could provide the accelerating gradients needed for next generation particle accelerators with compact, GV/m-scale devices. However, accelerator applications are limited by significant losses during transport of THz radiation from the generating nonlinear crystal to the acceleration structure. In addition, the spectral properties of high-field THz sources make it difficult to couple THz radiation into accelerating structures. A better understanding of the THz near-field source properties and how they are affected by changes in the generation setup is necessary for the optimization of THz transport and coupling. We demonstrate a technique for robust spatial and temporal characterization of single cycle strong field THz pulses in the near-field of a LiNbO 3 source using electro-optic sampling. Using this technique we have reconstructed the full temporal 3D THz near-field close to the LiNbO 3 emission face. Our results will help to inform designs of novel structures for use in THz time domain spectroscopy, THz particle acceleration, and ultrafast beam manipulation.
- 22 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Open AccessTemporal and Spatial Characterization of Ultrafast Terahertz Near-Fields for Particle Acceleration
Terahertz generation by optical rectification in LiNbO 3 using the tilted pulse front method is a powerful technique that is routinely used to generate THz pulses with energies in the tens of micro-joules and field strengths above 1 MV/cm. THz-frequency accelerating structures that utilize these fields could provide the accelerating gradients needed for next generation particle accelerators with compact, GV/m-scale devices. However, accelerator applications are limited by significant losses during transport of THz radiation from the generating nonlinear crystal to the acceleration structure. In addition, the spectral properties of high-field THz sources make it difficult to couple THz radiation into accelerating structures. A better understanding of the THz near-field source properties and how they are affected by changes in the generation setup is necessary for the optimization of THz transport and coupling. We demonstrate a technique for robust spatial and temporal characterization of single cycle strong field THz pulses in the near-field of a LiNbO 3 source using electro-optic sampling. Using this technique we have reconstructed the full temporal 3D THz near-field close to the LiNbO 3 emission face. Our results will help to inform designs of novel structures for use in THz time domain spectroscopy, THz particle acceleration, and ultrafast beam manipulation.
- 1 January 2022
- Published by Optica Publishing Group
- Vol. 44, STu4L.3
Time-Stamping of Ultrafast Electron Probes Using Terahertz Radiation
We show a method for detection and correction of the time-of-arrival jitter of electron bunches generated from an rf photoeinjector through Terahertz time-stamping, subsequently improving the temporal resolution of pump-probe UED measurements.
- 1 January 2022
- Published by Optica Publishing Group
- Vol. 44, STu4L.3
Time-Stamping of Ultrafast Electron Probes Using Terahertz Radiation
We show a method for detection and correction of the time-of-arrival jitter of electron bunches generated from an rf photoeinjector through Terahertz time-stamping, subsequently improving the temporal resolution of pump-probe UED measurements.
- 17 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69  (1) , 35-39
Low Phase Noise Oscillator Design Using Degenerate Band Edge Ladder Architectures
A new approach based on a strong degeneracy state to design oscillators that exhibit low phase noise and low power consumption is presented. A 100-MHz oscillator is designed using a periodic structure based on a degenerate band edge that is augmented with an NMOS cross-coupled pair. The analysis and simulation results show 16 dB phase noise improvement compared to oscillators based on a conventional single-ladder periodic structure. It is also shown that this oscillator dissipates less power than a conventional LC oscillator that requires a buffer to drive a 50Ω load.
- 17 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69  (1) , 35-39
Low Phase Noise Oscillator Design Using Degenerate Band Edge Ladder Architectures
A new approach based on a strong degeneracy state to design oscillators that exhibit low phase noise and low power consumption is presented. A 100-MHz oscillator is designed using a periodic structure based on a degenerate band edge that is augmented with an NMOS cross-coupled pair. The analysis and simulation results show 16 dB phase noise improvement compared to oscillators based on a conventional single-ladder periodic structure. It is also shown that this oscillator dissipates less power than a conventional LC oscillator that requires a buffer to drive a 50Ω load.
- 8 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Terahertz Dual-Fed Relativistic Electron Bunch Compression
We present results of a THz-driven dual-fed electron bunch compression experiment. We have used two counter-propagating single-cycle THz pulses, generated by optical rectification in the nonlinear organic crystal OH1, to feed a tapered parallel-plate waveguide bunch compressor structure. We report measurement of sub 40 fs rms bunches, achieving compression by factor of 4 and jitter reduction by a factor of 3.6. This approach will open new frontiers toward revealing new dynamical behavior with unprecedented temporal resolution in exotic materials using UED.
- 8 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Terahertz Dual-Fed Relativistic Electron Bunch Compression
We present results of a THz-driven dual-fed electron bunch compression experiment. We have used two counter-propagating single-cycle THz pulses, generated by optical rectification in the nonlinear organic crystal OH1, to feed a tapered parallel-plate waveguide bunch compressor structure. We report measurement of sub 40 fs rms bunches, achieving compression by factor of 4 and jitter reduction by a factor of 3.6. This approach will open new frontiers toward revealing new dynamical behavior with unprecedented temporal resolution in exotic materials using UED.
- 15 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 48  (12) , 4356-4364
Experimental Testing of a 3-D-Printed Metamaterial Slow Wave Structure for High-Power Microwave Generation
A high-power-microwave (HPM) source consisting of a backward wave oscillator (BWO) based on a metamaterial slow wave structure (MTM SWS) is investigated and tested. The MTM SWS is composed of a circular waveguide with periodic loading of two complementary electric split-ring resonator (CeSRR) disks and was designed at the University of California, Irvine, CA, USA (UCI). This SWS has been studied and simulated to quantify its cold structure properties. Moreover, a BWO using the proposed SWS has been simulated using a particle-in-cell solver to evaluate its performance. In the simulations, this BWO has generated 88-MW peak power in a pulse duration on the order of 15 ns with frequency about 2.9 GHz. This SWS was fabricated using 3-D printing and copper plating technology and was tested using the SINUS-6 pulsed electron beam accelerator at the University of New Mexico, Albuquerque, NM, USA (UNM). An output of 22 MW at 3.0 GHz was observed in experiments.
- 15 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 48  (12) , 4356-4364
Experimental Testing of a 3-D-Printed Metamaterial Slow Wave Structure for High-Power Microwave Generation
A high-power-microwave (HPM) source consisting of a backward wave oscillator (BWO) based on a metamaterial slow wave structure (MTM SWS) is investigated and tested. The MTM SWS is composed of a circular waveguide with periodic loading of two complementary electric split-ring resonator (CeSRR) disks and was designed at the University of California, Irvine, CA, USA (UCI). This SWS has been studied and simulated to quantify its cold structure properties. Moreover, a BWO using the proposed SWS has been simulated using a particle-in-cell solver to evaluate its performance. In the simulations, this BWO has generated 88-MW peak power in a pulse duration on the order of 15 ns with frequency about 2.9 GHz. This SWS was fabricated using 3-D printing and copper plating technology and was tested using the SINUS-6 pulsed electron beam accelerator at the University of New Mexico, Albuquerque, NM, USA (UNM). An output of 22 MW at 3.0 GHz was observed in experiments.