Jialuo Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jialuo Chen has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Satish Kumar
G. W. Woodruff School of Mechanical Engineering , Georgia Institute of Technology, Atlanta, Georgia, UNITED STATES
2 shared publicationsArdalan Lotfi
1 shared publication- Diego Vaca
School of Mechanical Engineering, Georgia Institute of Technology 1 , Atlanta, Georgia 30332, USA
1 shared publication Nitish Kumar
Georgia Institute of Technology, Atlanta, Georgia, United States
1 shared publication- Peter J. Hesketh
George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, 801 Ferst Dr, Atlanta, GA 30332, USA
1 shared publication Saswat Mishra
Georgia Institute of Technology, Atlanta, Georgia, United States
1 shared publication
Latest Publications
- 19 March 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 31 (23) , 235301
Thin dielectric-layer-enabled low-voltage operation of fully printed flexible carbon nanotube thin-film transistors
The quality of printable dielectric layer has become one of the major obstacles to achieving high-performance fully printed transistors. A thick dielectric layer will require high gate voltage to switch the transistors on and off, which will cause high power dissipation in printed devices. In response to this challenge, fully printed carbon nanotube (CNT)-based thin-film transistors (TFTs) have been fabricated on flexible membranes such as polyimide and liquid crystal polymer using aerosol jet printing. These devices can be operated at bias voltages below ±10 V (drain/gate voltages around ±6 V). This is much smaller than the previously reported values for fully printed CNT-TFTs because of using xdi-dcs (mixture of poly(vinylphenol)/poly (methylsilsesquioxane)) as the dielectric and using a single printing method. The lower voltage is a consequence of a thin dielectric layer (∼300 nm) and good uniformity in the printed CNT network. The printed CNT-TFTs show on/off ratio >10 5 , and mobility >5 cm 2 V −1 s −1 . Layer-by-layer deposition of CNT allows highly uniform and dense network formation, and the optimization of the xdi-dcs concentration using natural butyl alcohol provides high-yield printing of a thin dielectric layer. Collectively, this work shows the potential of using fully printed CNT-TFTs in various flexible electronic applications such as wearable sensors, actuators, artificial skin, displays and wireless tags and antennas.
- 19 March 2020
- Published by IOP Publishing in Nanotechnology
- Vol. 31 (23) , 235301
Thin dielectric-layer-enabled low-voltage operation of fully printed flexible carbon nanotube thin-film transistors
The quality of printable dielectric layer has become one of the major obstacles to achieving high-performance fully printed transistors. A thick dielectric layer will require high gate voltage to switch the transistors on and off, which will cause high power dissipation in printed devices. In response to this challenge, fully printed carbon nanotube (CNT)-based thin-film transistors (TFTs) have been fabricated on flexible membranes such as polyimide and liquid crystal polymer using aerosol jet printing. These devices can be operated at bias voltages below ±10 V (drain/gate voltages around ±6 V). This is much smaller than the previously reported values for fully printed CNT-TFTs because of using xdi-dcs (mixture of poly(vinylphenol)/poly (methylsilsesquioxane)) as the dielectric and using a single printing method. The lower voltage is a consequence of a thin dielectric layer (∼300 nm) and good uniformity in the printed CNT network. The printed CNT-TFTs show on/off ratio >10 5 , and mobility >5 cm 2 V −1 s −1 . Layer-by-layer deposition of CNT allows highly uniform and dense network formation, and the optimization of the xdi-dcs concentration using natural butyl alcohol provides high-yield printing of a thin dielectric layer. Collectively, this work shows the potential of using fully printed CNT-TFTs in various flexible electronic applications such as wearable sensors, actuators, artificial skin, displays and wireless tags and antennas.
- 1 February 2019
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 281, 1080-1087
Carbon nanotube thin-film-transistors for gas identification
- 1 February 2019
- Published by Elsevier in Sensors and Actuators B: Chemical
- Vol. 281, 1080-1087
Carbon nanotube thin-film-transistors for gas identification
- 7 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 17 (2) , 353-361
Variability in Output Characteristics of Single-Walled Carbon Nanotube Thin-Film Transistors
Single-walled carbon nanotube (CNT) based thin film transistors (TFTs) are promising candidates for future electronic devices because of their excellent properties. However, device-to-device performance variability of TFTs can pose challenging problems which is rooted in the randomness of CNT networks, the variation in individual CNT properties due to change in chirality, and the fabrication imperfections. This work presents a systematic study of variability in I-V characteristics through a combination of experimental and theoretical analysis of the major sources which cause performance variation. The sources of variation including % of metallic CNT (m-CNTs), threshold voltage, CNT mean length and CNT network density have been studied separately. The analysis shows that the presence of m-CNT is a major source contributing to the performance variation for short channel TFTs, but its effect reduces for large channel length transistors. The threshold voltage is found to be the major source of variation for long channel TFTs. A better consistency in performance can be guaranteed for TFTs with larger channel area, which ensures a smaller variation in CNT network density and CNT mean length. These results provide key insights into the variability estimation of I-V characteristics of CNT based devices which is vital for reliability studies of CNT-TFTs based circuits for different electronic applications.
- 7 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 17 (2) , 353-361
Variability in Output Characteristics of Single-Walled Carbon Nanotube Thin-Film Transistors
Single-walled carbon nanotube (CNT) based thin film transistors (TFTs) are promising candidates for future electronic devices because of their excellent properties. However, device-to-device performance variability of TFTs can pose challenging problems which is rooted in the randomness of CNT networks, the variation in individual CNT properties due to change in chirality, and the fabrication imperfections. This work presents a systematic study of variability in I-V characteristics through a combination of experimental and theoretical analysis of the major sources which cause performance variation. The sources of variation including % of metallic CNT (m-CNTs), threshold voltage, CNT mean length and CNT network density have been studied separately. The analysis shows that the presence of m-CNT is a major source contributing to the performance variation for short channel TFTs, but its effect reduces for large channel length transistors. The threshold voltage is found to be the major source of variation for long channel TFTs. A better consistency in performance can be guaranteed for TFTs with larger channel area, which ensures a smaller variation in CNT network density and CNT mean length. These results provide key insights into the variability estimation of I-V characteristics of CNT based devices which is vital for reliability studies of CNT-TFTs based circuits for different electronic applications.