Giampaolo D'ALessandro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Giampaolo D'ALessandro has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Filippo de Monte
Department of Industrial and Information Engineering and Economics, University of L’Aquila, 67100 L’Aquila, Italy
14 shared publications - James V. Beck
Department of Mechanical Engineering, Michigan State University, East Lansing, MI 48824
4 shared publications - Robert L. McMasters
Department of Mechanical Engineering, Virginia Military Institute, Lexington, VA 24450
4 shared publications - Marco Iezzi
G-Plus Technology S.r.l, 66100 Chieti, Italy, Italy
2 shared publications - Stefano Sfarra
University of L’Aquila
2 shared publications César Cunha Pacheco
1 shared publication
Latest Publications
- Open Access
- 9 November 2026
- Published by MDPI AG in Preprints.org
Thermodynamic Analysis of a Flash Tank
A two-phase thermodynamic model of a flash tank (FT) is proposed to predict the dy-namics of a flash tank operating with a pure substance. The model is based on the mass and energy balance equations applied to the liquid and vapor phases. It consists of five different cases related to both tank pressure changes and thermodynamic conditions of the two phases. This permits us to consider the spontaneous condensation of part of the vapor resident in the tank and/or spontaneous flashing of a fraction of resident liquid. Once the FT inlet total mass flow rate is assigned, the ones of incoming flash vapor and saturated liquid are computed as a function of the time-dependent tank pressure. A pro-cedure for computing the liquid level inside the tank is also given. As numerical tests, the thermodynamic model is applied first to a flash tank used for steam generation (powered by high temperature heat pumps or low temperature solar collectors), and then to the transient operating of a flash tank vapor injection system for a vapor-compression heat pump.
- 9 November 2026
- Published by MDPI AG in Preprints.org
Open AccessThermodynamic Analysis of a Flash Tank
A two-phase thermodynamic model of a flash tank (FT) is proposed to predict the dy-namics of a flash tank operating with a pure substance. The model is based on the mass and energy balance equations applied to the liquid and vapor phases. It consists of five different cases related to both tank pressure changes and thermodynamic conditions of the two phases. This permits us to consider the spontaneous condensation of part of the vapor resident in the tank and/or spontaneous flashing of a fraction of resident liquid. Once the FT inlet total mass flow rate is assigned, the ones of incoming flash vapor and saturated liquid are computed as a function of the time-dependent tank pressure. A pro-cedure for computing the liquid level inside the tank is also given. As numerical tests, the thermodynamic model is applied first to a flash tank used for steam generation (powered by high temperature heat pumps or low temperature solar collectors), and then to the transient operating of a flash tank vapor injection system for a vapor-compression heat pump.
- Open Access
Steam Generating High Temperature Heat Pumps: Best Practices, Optimization Strategies and Refrigerant Selection for Performance Improvement
The present paper provides a general overview of the state of the art of steam generating heat pumps (SGHPs) technology employed in the industrial field. Recommended best practices and optimization procedures for overall performance improvement of compression closed-loop-based systems are described in detail, as well as the main modifications of the thermodynamic heat pump cycle. Once the main configurations of SGHPs are described, the different concepts are compared in terms of supply temperature ranges; cases of comparison among different concepts are reviewed, and techno-economic barriers are also discussed. The working fluids (including natural refrigerants) commonly selected for these steam generating systems are presented along with their uses. Moreover, zeotropic refrigerant mixtures and new potentially usable mixtures are mentioned. After that, refrigerant selection criteria for high temperature heat pumps are also discussed. Then, using an internal heat exchanger, refrigerant injection technique and super heating in lubricated compressors are herein presented as best practices for general performance improvement. Regarding thermodynamic cycle modifications, basic auto-cascade and quasi-two-stage compression cycles are discussed along with further improvements suggested in the specialized literature. Lastly, optimization strategies useful to enhance the heat pumps’ design and based on TOPSIS method, advanced exergy analysis, exergy-based cost minimization and combined design are analyzed.
Open AccessSteam Generating High Temperature Heat Pumps: Best Practices, Optimization Strategies and Refrigerant Selection for Performance Improvement
The present paper provides a general overview of the state of the art of steam generating heat pumps (SGHPs) technology employed in the industrial field. Recommended best practices and optimization procedures for overall performance improvement of compression closed-loop-based systems are described in detail, as well as the main modifications of the thermodynamic heat pump cycle. Once the main configurations of SGHPs are described, the different concepts are compared in terms of supply temperature ranges; cases of comparison among different concepts are reviewed, and techno-economic barriers are also discussed. The working fluids (including natural refrigerants) commonly selected for these steam generating systems are presented along with their uses. Moreover, zeotropic refrigerant mixtures and new potentially usable mixtures are mentioned. After that, refrigerant selection criteria for high temperature heat pumps are also discussed. Then, using an internal heat exchanger, refrigerant injection technique and super heating in lubricated compressors are herein presented as best practices for general performance improvement. Regarding thermodynamic cycle modifications, basic auto-cascade and quasi-two-stage compression cycles are discussed along with further improvements suggested in the specialized literature. Lastly, optimization strategies useful to enhance the heat pumps’ design and based on TOPSIS method, advanced exergy analysis, exergy-based cost minimization and combined design are analyzed.
- Open Access
- 17 February 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (4) , 1603
A Review of Techniques and Bio-Heat Transfer Models Supporting Infrared Thermal Imaging for Diagnosis of Malignancy
The present review aims to analyze the application of infrared thermal imaging, aided by bio-heat models, as a tool for the diagnosis of skin and breast cancers. The state of the art of the related technical procedures, bio-heat transfer modeling, and thermogram post-processing methods is comprehensively reviewed. Once the thermal signatures of different malignant diseases are described, the updated thermographic techniques (steady-state and dynamic) used for cancer diagnosis are discussed in detail, along with the recommended best practices to ensure the most significant thermal contrast observable between the cancerous and healthy tissues. Regarding the dynamic techniques, particular emphasis is placed on innovative methods, such as lock-in thermography, thermal wave imaging, and rotational breast thermography. Forward and inverse modeling techniques for the bio-heat transfer in skin and breast tissues, supporting the thermographic examination and providing accurate data for training artificial intelligence (AI) algorithms, are reported with a special focus on real breast geometry-based 3D models. In terms of inverse techniques, different data processing algorithms to retrieve thermophysical parameters and growth features of tumor lesions are mentioned. Post-processing of infrared images is also described, citing both conventional processing procedures and applications of AI algorithms for tumor detection.
- 17 February 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (4) , 1603
Open AccessA Review of Techniques and Bio-Heat Transfer Models Supporting Infrared Thermal Imaging for Diagnosis of Malignancy
The present review aims to analyze the application of infrared thermal imaging, aided by bio-heat models, as a tool for the diagnosis of skin and breast cancers. The state of the art of the related technical procedures, bio-heat transfer modeling, and thermogram post-processing methods is comprehensively reviewed. Once the thermal signatures of different malignant diseases are described, the updated thermographic techniques (steady-state and dynamic) used for cancer diagnosis are discussed in detail, along with the recommended best practices to ensure the most significant thermal contrast observable between the cancerous and healthy tissues. Regarding the dynamic techniques, particular emphasis is placed on innovative methods, such as lock-in thermography, thermal wave imaging, and rotational breast thermography. Forward and inverse modeling techniques for the bio-heat transfer in skin and breast tissues, supporting the thermographic examination and providing accurate data for training artificial intelligence (AI) algorithms, are reported with a special focus on real breast geometry-based 3D models. In terms of inverse techniques, different data processing algorithms to retrieve thermophysical parameters and growth features of tumor lesions are mentioned. Post-processing of infrared images is also described, citing both conventional processing procedures and applications of AI algorithms for tumor detection.
- 13 June 2023
- Published by ASME International in ASME Journal of Heat and Mass Transfer
- Vol. 145 (9) , 1-23
The Effect of Biot Number on a Generalized Heat Conduction Solution
Analytical solutions for thermal conduction problems are extremely important, particularly for verification of numerical codes. Temperatures and heat fluxes can be calculated very precisely, normally to eight or ten significant figures, even in situations involving large temperature gradients. It can be convenient to have a general analytical solution for a transient conduction problem in rectangular coordinates. The general solution is based on the principle that the three primary types of boundary conditions (prescribed temperature, prescribed heat flux, and convective) can all be handled using convective boundary conditions. A large convection coefficient closely approximates a prescribed temperature boundary condition and a very low convection coefficient closely approximates an insulated boundary condition. Since a dimensionless solution is used in this research, the effect of various values of dimensionless convection coefficients, or Biot number values, are explored. An understandable concern with a general analytical solution is the effect of the choice of convection coefficients on the precision of the solution, since the primary motivation for using analytical solutions is the precision offered. An investigation is made in this study to determine the effects of the choices of large and small convection coefficients on the precision of the analytical solutions generated by the general convective formulation. Results are provided, in tabular and graphical form, to illustrate the effects of the choices of convection coefficients on the precision of the general analytical solution.
- 13 June 2023
- Published by ASME International in ASME Journal of Heat and Mass Transfer
- Vol. 145 (9) , 1-23
The Effect of Biot Number on a Generalized Heat Conduction Solution
Analytical solutions for thermal conduction problems are extremely important, particularly for verification of numerical codes. Temperatures and heat fluxes can be calculated very precisely, normally to eight or ten significant figures, even in situations involving large temperature gradients. It can be convenient to have a general analytical solution for a transient conduction problem in rectangular coordinates. The general solution is based on the principle that the three primary types of boundary conditions (prescribed temperature, prescribed heat flux, and convective) can all be handled using convective boundary conditions. A large convection coefficient closely approximates a prescribed temperature boundary condition and a very low convection coefficient closely approximates an insulated boundary condition. Since a dimensionless solution is used in this research, the effect of various values of dimensionless convection coefficients, or Biot number values, are explored. An understandable concern with a general analytical solution is the effect of the choice of convection coefficients on the precision of the solution, since the primary motivation for using analytical solutions is the precision offered. An investigation is made in this study to determine the effects of the choices of large and small convection coefficients on the precision of the analytical solutions generated by the general convective formulation. Results are provided, in tabular and graphical form, to illustrate the effects of the choices of convection coefficients on the precision of the general analytical solution.
- Open Access
Modeling and Measuring Thermodynamic and Transport Thermophysical Properties: A Review
The present review describes the up-to-date state of the evaluation of thermophysical properties (TP) of materials with three different procedures: modeling (also including inverse problems), measurements and analytical methods (e.g., through computing from other properties). Methods to measure specific heat and thermal conductivity are described in detail. Thermal diffusivity and thermal effusivity are a combination of the previously cited properties, but also for these properties, specific measurement and calculation methods are reported. Experiments can be carried out in steady-state, transient, and pulse regimes. For modeling, special focus is given to the inverse methods and parameter estimation procedures, because through them it is possible to evaluate the thermophysical property, assuring the best practices and supplying the measurement uncertainty. It is also cited when the most common data processing algorithms are used, e.g., the Gauss–Newton and Levenberg–Marquardt least squares minimization algorithms, and how it is possible to retrieve values of TP from other data. Optimization criteria for designing the experiments are also mentioned.
Open AccessModeling and Measuring Thermodynamic and Transport Thermophysical Properties: A Review
The present review describes the up-to-date state of the evaluation of thermophysical properties (TP) of materials with three different procedures: modeling (also including inverse problems), measurements and analytical methods (e.g., through computing from other properties). Methods to measure specific heat and thermal conductivity are described in detail. Thermal diffusivity and thermal effusivity are a combination of the previously cited properties, but also for these properties, specific measurement and calculation methods are reported. Experiments can be carried out in steady-state, transient, and pulse regimes. For modeling, special focus is given to the inverse methods and parameter estimation procedures, because through them it is possible to evaluate the thermophysical property, assuring the best practices and supplying the measurement uncertainty. It is also cited when the most common data processing algorithms are used, e.g., the Gauss–Newton and Levenberg–Marquardt least squares minimization algorithms, and how it is possible to retrieve values of TP from other data. Optimization criteria for designing the experiments are also mentioned.
- 20 June 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA)
One-Dimensional Analytical Solution for Transient Thermal Conduction a Hollow Cylinder
View Video Presentation: https://doi.org/10.2514/6.2022-3367.vid The primary use of analytical solutions in the area of thermal conduction problems is for verification purposes, comparing the calculated temperatures and heat flux values to the results from numerical codes. The contribution from the analytical solutions can be especially significant where large temperature gradients are found. This is because the temperature and heat flux results can be found very precisely, normally to eight or ten significant figures using analytical solutions. Normally numerical solutions require extremely fine grids in high-heat-flux locations, but analytical solutions can provide insight into the adequacy of grid densities in these types of situations. One area of particular interest is in non-rectangular analytical solutions since generalized numerical grids do not naturally lend themselves well to curved surfaces without a large number of nodes. In this current study, four solutions are offered in a geometry involving a hollow cylinder. Two of the solutions examine heating from the inside of the cylinder and two involve heating from the outside. Development of the solutions is provided along with results which show the temperature responses to the various sets of boundary conditions. Intrinsic verification is also applied in order to provide assurance that the solutions are properly formulated and evaluated.
- 20 June 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA)
One-Dimensional Analytical Solution for Transient Thermal Conduction a Hollow Cylinder
View Video Presentation: https://doi.org/10.2514/6.2022-3367.vid The primary use of analytical solutions in the area of thermal conduction problems is for verification purposes, comparing the calculated temperatures and heat flux values to the results from numerical codes. The contribution from the analytical solutions can be especially significant where large temperature gradients are found. This is because the temperature and heat flux results can be found very precisely, normally to eight or ten significant figures using analytical solutions. Normally numerical solutions require extremely fine grids in high-heat-flux locations, but analytical solutions can provide insight into the adequacy of grid densities in these types of situations. One area of particular interest is in non-rectangular analytical solutions since generalized numerical grids do not naturally lend themselves well to curved surfaces without a large number of nodes. In this current study, four solutions are offered in a geometry involving a hollow cylinder. Two of the solutions examine heating from the inside of the cylinder and two involve heating from the outside. Development of the solutions is provided along with results which show the temperature responses to the various sets of boundary conditions. Intrinsic verification is also applied in order to provide assurance that the solutions are properly formulated and evaluated.
- Open Access
- 16 July 2021
- Published by ASME International
Verification of Ansys and Matlab Conduction Results Using Analytical Solutions
Division / Sponsors: Heat Transfer Division (HTD), Fluids Engineering Division (FED)
- 16 July 2021
- Published by ASME International
Open AccessVerification of Ansys and Matlab Conduction Results Using Analytical Solutions
Division / Sponsors: Heat Transfer Division (HTD), Fluids Engineering Division (FED)