Pietrogiovanni Cerchier
Research Subjects
Research Interests
Pietrogiovanni Cerchier has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Manuele Dabalà
Department of Industrial Engineering, University of Padova, via Marzolo 9, 35131 Padova, Italy
8 shared publications - Katya Brunelli
Department of Industrial Engineering, University of Padova, via Marzolo 9, 35131 Padova, Italy
6 shared publications Katya Brunelli
Department of Industrial Engineering, University of Padua, Padova, Italy
4 shared publications- Luca Pezzato
Institute of Condensed Matter Chemistry and Energy Technologies, National Research Council of Italy, 35127 Padova, Italy
3 shared publications - Francesco Miserocchi
9-TECH,Italy
2 shared publications Luca Pezzato
Department of Industrial Engineering, University of Padua, Padova, Italy
2 shared publications
Latest Publications
- Open Access
- 21 August 2026
- Published by Elsevier in Journal of Cleaner Production
- Vol. 575
Comparative assessment of photovoltaic waste generation across European countries
- 21 August 2026
- Published by Elsevier in Journal of Cleaner Production
- Vol. 575
Open AccessComparative assessment of photovoltaic waste generation across European countries
- 16 September 2025
- Published by Eurowaste SRL in Detritus
- No. 32,p. 95-103
MATERIAL RECOVERY FROM PHOTOVOLTAIC PANELS BY MEANS OF THERMAL TREATMENT: THE EFFECT OF BACKSHEET REMOVAL.
The thermal combustion of polymers contained in PV has been studied by 9-Tech, and it has been shown to be an efficacious way to recover from end-of-life (EoL) photovoltaic secondary raw materials with high efficiency and purity. In this work, the removal of the backsheet from photovoltaic (PV) panels has been investigated as a pre-treatment step in the thermal recycling process, assessing its impact on material recovery, energy consumption, and environmental emissions. The backsheet has been removed by means of an innovative technology developed by CEA based on sanding. The analysis of the materials recovered from PV panels with and without backsheet indicated that backsheet removal improves material purity by eliminating contamination with titanium dioxide (TiO₂) powder. Furthermore, it reduced dust emissions and avoided the production of toxic hydrofluoric acid. Finally, it also slightly increased energy consumption due to the removal of combustible polymeric material.
- 16 September 2025
- Published by Eurowaste SRL in Detritus
- No. 32,p. 95-103
MATERIAL RECOVERY FROM PHOTOVOLTAIC PANELS BY MEANS OF THERMAL TREATMENT: THE EFFECT OF BACKSHEET REMOVAL.
The thermal combustion of polymers contained in PV has been studied by 9-Tech, and it has been shown to be an efficacious way to recover from end-of-life (EoL) photovoltaic secondary raw materials with high efficiency and purity. In this work, the removal of the backsheet from photovoltaic (PV) panels has been investigated as a pre-treatment step in the thermal recycling process, assessing its impact on material recovery, energy consumption, and environmental emissions. The backsheet has been removed by means of an innovative technology developed by CEA based on sanding. The analysis of the materials recovered from PV panels with and without backsheet indicated that backsheet removal improves material purity by eliminating contamination with titanium dioxide (TiO₂) powder. Furthermore, it reduced dust emissions and avoided the production of toxic hydrofluoric acid. Finally, it also slightly increased energy consumption due to the removal of combustible polymeric material.
- 25 October 2024
- Published by Eurowaste SRL in Detritus
- Vol. 29 (29) , 54-62
PHOTOVOLTAIC PANEL RECYCLING: TESTS IN THE PILOT PLANT IN VENICE AND SILICON APPLICATIONS FOR FERROALLOY PRODUCTION
In 2020 9-Tech developed one of the most advanced technologies in Europe for recycling PV panels. In detail, the proposed technology is able to recover all the valuable materials contained in PV panels (aluminum, glass, copper ribbons, silver, silicon PV cells). The pilot plant, authorized by Veneto region in 2022, has been operating in 2023 showing good performances. The recovered PV cells contain mainly silicon that is a Critical and Strategic Raw Material, but the presence of aluminum paste and silicon nitride makes challenging its reuse. Therefore, several uses for silicon are being investigated under the PARSIVAL project, specifically in the photovoltaic sector, battery anode manufacture, and ferroalloy production use. In this work, the results of the tests in the pilot plant with the 9-Tech technology and the main findings regarding the possible use of the PV cells as reagent in STILLMETAL process for the production of ferrosilicon alloys are presented.
- 25 October 2024
- Published by Eurowaste SRL in Detritus
- Vol. 29 (29) , 54-62
PHOTOVOLTAIC PANEL RECYCLING: TESTS IN THE PILOT PLANT IN VENICE AND SILICON APPLICATIONS FOR FERROALLOY PRODUCTION
In 2020 9-Tech developed one of the most advanced technologies in Europe for recycling PV panels. In detail, the proposed technology is able to recover all the valuable materials contained in PV panels (aluminum, glass, copper ribbons, silver, silicon PV cells). The pilot plant, authorized by Veneto region in 2022, has been operating in 2023 showing good performances. The recovered PV cells contain mainly silicon that is a Critical and Strategic Raw Material, but the presence of aluminum paste and silicon nitride makes challenging its reuse. Therefore, several uses for silicon are being investigated under the PARSIVAL project, specifically in the photovoltaic sector, battery anode manufacture, and ferroalloy production use. In this work, the results of the tests in the pilot plant with the 9-Tech technology and the main findings regarding the possible use of the PV cells as reagent in STILLMETAL process for the production of ferrosilicon alloys are presented.
- Open Access
- 30 August 2024
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 211
Life cycle assessment of Al-Cu-Ag-Si recycling process from photovoltaic waste
- 30 August 2024
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 211
Open AccessLife cycle assessment of Al-Cu-Ag-Si recycling process from photovoltaic waste
- Open Access
Production and Characterization of Photocatalytic PEO Coatings Containing TiO2 Powders Recovered from Wastes
In this work, the possibility of incorporating TiO2 titanium dioxide particles derived from the recycling process of photovoltaic panels into PEO coatings was investigated. These particles constitute the main filler of the polymer constituting the rear part of the panels, and are characterized by possessing photocatalytic properties. The particles were added in different quantities to the electrolyte (a basic solution containing sodium silicate). The incorporation into the PEO coating produced on an aluminum alloy 1050, and the possibility of conferring photocatalytic properties to the surface of the samples were studied. The different samples were first characterized by optical microscope analysis, SEM and XRD and from the point of view of corrosion resistance by means of potentiodynamic tests. The photocatalytic properties of the samples were evaluated by monitoring the degradation of aqueous solutions of methylene blue exposed to a UV lamp. The particles have been successfully incorporated into the coating, and their presence does not alter the corrosion properties, which are improved compared to the uncoated sample. The particles, initially composed of a mixture of rutile and anatase, are instead transformed into rutile after incorporation due to the locally very high temperatures that can occur during the PEO process. In the samples obtained with higher quantities of titanium dioxide particles (60 and 80 g/L), a significant photocatalytic effect is observed with a significant reduction of methylene blue.
Open AccessProduction and Characterization of Photocatalytic PEO Coatings Containing TiO2 Powders Recovered from Wastes
In this work, the possibility of incorporating TiO2 titanium dioxide particles derived from the recycling process of photovoltaic panels into PEO coatings was investigated. These particles constitute the main filler of the polymer constituting the rear part of the panels, and are characterized by possessing photocatalytic properties. The particles were added in different quantities to the electrolyte (a basic solution containing sodium silicate). The incorporation into the PEO coating produced on an aluminum alloy 1050, and the possibility of conferring photocatalytic properties to the surface of the samples were studied. The different samples were first characterized by optical microscope analysis, SEM and XRD and from the point of view of corrosion resistance by means of potentiodynamic tests. The photocatalytic properties of the samples were evaluated by monitoring the degradation of aqueous solutions of methylene blue exposed to a UV lamp. The particles have been successfully incorporated into the coating, and their presence does not alter the corrosion properties, which are improved compared to the uncoated sample. The particles, initially composed of a mixture of rutile and anatase, are instead transformed into rutile after incorporation due to the locally very high temperatures that can occur during the PEO process. In the samples obtained with higher quantities of titanium dioxide particles (60 and 80 g/L), a significant photocatalytic effect is observed with a significant reduction of methylene blue.
- Open Access
- 30 September 2021
- Published by Eurowaste SRL in Detritus
- Vol. 16 (16) , 41-47
Innovative recycling of end of life silicon PV panels: ReSiELP
In Europe, an increasing amount of End of Life (EoL) photovoltaic silicon (PV) panels is expected to be collected in the next 20 years. The silicon PV modules represent a new type of electronic waste that shows challenges and opportunities. ReSiELP was a European project that aimed at recovery of valuable materials (aluminum, glass, copper, silicon, and silver) from EoL silicon PV modules. During the project a pilot plant, constituted by a furnace, a gas abatement system, an apparatus for the mechanical separation and a hydrometallurgical plant was designed and built. The pilot plan was realized to upscale recycling technology to TRL 7, with a 1500 panels/year capacity. The feasibility of industrial-scale recovery and the reintegration of all recovered materials in their appropriate value chain was investigated. The results obtained showed that 2N purity silicon and 2N purity silver can be recovered with high efficiency. In order to realize a zero-waste plant, a hydrometallurgical process was developed for the wastewater treatment. Moreover, the use of recovered glass for building materials was investigated and the obtained performance seemed comparable with commercial products.
- 30 September 2021
- Published by Eurowaste SRL in Detritus
- Vol. 16 (16) , 41-47
Open AccessInnovative recycling of end of life silicon PV panels: ReSiELP
In Europe, an increasing amount of End of Life (EoL) photovoltaic silicon (PV) panels is expected to be collected in the next 20 years. The silicon PV modules represent a new type of electronic waste that shows challenges and opportunities. ReSiELP was a European project that aimed at recovery of valuable materials (aluminum, glass, copper, silicon, and silver) from EoL silicon PV modules. During the project a pilot plant, constituted by a furnace, a gas abatement system, an apparatus for the mechanical separation and a hydrometallurgical plant was designed and built. The pilot plan was realized to upscale recycling technology to TRL 7, with a 1500 panels/year capacity. The feasibility of industrial-scale recovery and the reintegration of all recovered materials in their appropriate value chain was investigated. The results obtained showed that 2N purity silicon and 2N purity silver can be recovered with high efficiency. In order to realize a zero-waste plant, a hydrometallurgical process was developed for the wastewater treatment. Moreover, the use of recovered glass for building materials was investigated and the obtained performance seemed comparable with commercial products.
- 1 April 2019
- Published by SAGE Publications in Surface Engineering
- Vol. 35 (4) , 325-333
Plasma electrolytic oxidation coatings with fungicidal properties
Plasma electrolytic oxidation (PEO) is a relatively new surface treatment that permits to increase the corrosion and wear resistance of metals. One of the peculiarities of the process is the possibility to incorporate into the produced coating the particles suspended in the electrolyte. In this work, micrometric silver particles were added in the PEO coating to innovatively give a fungicidal effect to the samples due to the presence of silver, whose fungicidal effect is well known. PEO coatings were produced on aluminium alloy 7075 using an electrolyte containing sodium silicate and silver particles. The thickness, morphology, composition and corrosion resistance of the obtained coatings were studied. The fungicidal properties were evaluated with contact tests of 2 and 4 h using Candida albicans ATCC 10231. Silver particles were homogeneously distributed in the coating and the silver-containing samples were characterised by improved corrosion resistance and high fungicidal activity.
- 1 April 2019
- Published by SAGE Publications in Surface Engineering
- Vol. 35 (4) , 325-333
Plasma electrolytic oxidation coatings with fungicidal properties
Plasma electrolytic oxidation (PEO) is a relatively new surface treatment that permits to increase the corrosion and wear resistance of metals. One of the peculiarities of the process is the possibility to incorporate into the produced coating the particles suspended in the electrolyte. In this work, micrometric silver particles were added in the PEO coating to innovatively give a fungicidal effect to the samples due to the presence of silver, whose fungicidal effect is well known. PEO coatings were produced on aluminium alloy 7075 using an electrolyte containing sodium silicate and silver particles. The thickness, morphology, composition and corrosion resistance of the obtained coatings were studied. The fungicidal properties were evaluated with contact tests of 2 and 4 h using Candida albicans ATCC 10231. Silver particles were homogeneously distributed in the coating and the silver-containing samples were characterised by improved corrosion resistance and high fungicidal activity.
- 1 September 2018
- Published by Elsevier in International Biodeterioration & Biodegradation
- Vol. 133, 70-78
Antifouling properties of different Plasma Electrolytic Oxidation coatings on 7075 aluminium alloy
- 1 September 2018
- Published by Elsevier in International Biodeterioration & Biodegradation
- Vol. 133, 70-78
Antifouling properties of different Plasma Electrolytic Oxidation coatings on 7075 aluminium alloy
- 29 March 2018
- Published by Walter de Gruyter GmbH
Green synthesis of copper nanoparticles with ultrasound assistance
- 29 March 2018
- Published by Walter de Gruyter GmbH
Green synthesis of copper nanoparticles with ultrasound assistance