David de Carvalho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
David de Carvalho has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- António Guerner Dias
Faculdade de Ciências da Universidade do Porto
4 shared publications - João Alexandre Paschoalin Filho
University Nove de Julho, São Paulo, Brazil
4 shared publications - Paulo José Rocha de Albuquerque
State University of Campinas (UNICAMP)
4 shared publications - Andrea Ghermandi
School of Environmental Sciences, Faculty of Social Sciences, University of Haifa, Israel
2 shared publications Brenno Augusto Marcondes Versolatto
Nove de Julho University -Master Degree in Sustainable and Intelligent Cities, São Paulo/Brazil
2 shared publications- Diego Gonçalves Camelo
Aluno do Programa de Mestrado em Cidades Inteligentes e Sustentáveis/Uninove
2 shared publications
Latest Publications
- 7 August 2024
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 17 (9) , 1-10
Assessment of wastes used as gabion filling for lining works of a river located in Brazil
- 7 August 2024
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 17 (9) , 1-10
Assessment of wastes used as gabion filling for lining works of a river located in Brazil
- 13 April 2023
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 16 (5) , 1-9
The use of phosphogypsum for soil bricks manufacturing as an alternative for its sustainable destination
- 13 April 2023
- Published by Springer Nature in Arabian Journal of Geosciences
- Vol. 16 (5) , 1-9
The use of phosphogypsum for soil bricks manufacturing as an alternative for its sustainable destination
- Open Access
- 3 March 2023
- Published by Universidad Nacional de Colombia in DYNA
- Vol. 90 (225) , 122-130
Behavior of a new laterally top-loaded post-grouted micropile in highly porous lateritic soil
The use of micropiles has been increasing in recent years, mostly for horizontally loaded cases. Given the little information about this foundation type under lateral top-loading, especially in high-porosity and collapsible soils, a total of four transversal loading tests were carried out in a new post-grouted micropile configuration with length of 17 m and diameter of 0.3 m, two in natural soil moisture conditions and two in flooded conditions. Load-displacement curves and the horizontal reaction coefficient of the new micropile were obtained. Results were compared with other pile types laterally tested under the same conditions and in the same geological and geotechnical contexts. Generally, results were better than the other pile types, mainly under saturated condition. The new micropile proved to be a better and more efficient alternative for local lateritic soil treatment when compared with the soil-cement treatment. El uso de micropilotes ha crecido en los últimos años, principalmente para casos solicitados horizontalmente. Dada la poca información sobre este tipo de fundación cargada lateralmente, especialmente en suelos colapsables y de alta porosidad, se realizaron un total de cuatro ensayos de carga lateral en una nueva configuración de micropilote post-inyectado de 17 m de longitud y 0.3 m de diámetro, dos en condiciones naturales de humedad y dos en condiciones inundadas. Se obtuvieron las curvas carga-desplazamiento y el coeficiente de reacción horizontal del nuevo micropilote. Los resultados se compararon con otros tipos de pilotes ensayados lateralmente en las mismas condiciones y en los mismos contextos geológico y geotécnico. En general, los resultados fueron mejores que otros tipos de pilotes, especialmente en condiciones saturadas. El nuevo micropilote demonstró ser una alternativa mejor y más eficiente para tratamiento de lo suelo laterítico local en comparación con el tratamiento de suelo-cemento.
- 3 March 2023
- Published by Universidad Nacional de Colombia in DYNA
- Vol. 90 (225) , 122-130
Open AccessBehavior of a new laterally top-loaded post-grouted micropile in highly porous lateritic soil
The use of micropiles has been increasing in recent years, mostly for horizontally loaded cases. Given the little information about this foundation type under lateral top-loading, especially in high-porosity and collapsible soils, a total of four transversal loading tests were carried out in a new post-grouted micropile configuration with length of 17 m and diameter of 0.3 m, two in natural soil moisture conditions and two in flooded conditions. Load-displacement curves and the horizontal reaction coefficient of the new micropile were obtained. Results were compared with other pile types laterally tested under the same conditions and in the same geological and geotechnical contexts. Generally, results were better than the other pile types, mainly under saturated condition. The new micropile proved to be a better and more efficient alternative for local lateritic soil treatment when compared with the soil-cement treatment. El uso de micropilotes ha crecido en los últimos años, principalmente para casos solicitados horizontalmente. Dada la poca información sobre este tipo de fundación cargada lateralmente, especialmente en suelos colapsables y de alta porosidad, se realizaron un total de cuatro ensayos de carga lateral en una nueva configuración de micropilote post-inyectado de 17 m de longitud y 0.3 m de diámetro, dos en condiciones naturales de humedad y dos en condiciones inundadas. Se obtuvieron las curvas carga-desplazamiento y el coeficiente de reacción horizontal del nuevo micropilote. Los resultados se compararon con otros tipos de pilotes ensayados lateralmente en las mismas condiciones y en los mismos contextos geológico y geotécnico. En general, los resultados fueron mejores que otros tipos de pilotes, especialmente en condiciones saturadas. El nuevo micropilote demonstró ser una alternativa mejor y más eficiente para tratamiento de lo suelo laterítico local en comparación con el tratamiento de suelo-cemento.
- Open Access
- 2 February 2022
- Published by UNESP - Universidade Estadual Paulista in Geosciences = Geociências
- Vol. 40 (4) , 1137-1145
LÓGICA FUZZY APLICADA A ELABORAÇÃO DE CARTA GEOTÉCNICA DE APTIDÃO À URBANIZAÇÃO DA ÁREA DE EXPANSÃO DA UNICAMP - CAMPINAS, SP
A necessidade de se planejar e direcionar o uso e ocupação do solo fez com que surgissem variados métodos para esse fim, dentre estes a cartografia geotécnica. A avaliação da aptidão de terrenos para urbanização tem sido tradicionalmente realizada pela cartografia geotécnica, sendo atualmente fortemente apoiada em ferramentas de geoprocessamento. A lógica fuzzy é um método matemático que pode ser aplicado como ferramenta de geoprocessamento para fins cartográficos quando se necessita realizar a análise integrada de diversos temas. Este estudo objetivou testar a aplicação da lógica fuzzy para elaboração de carta geotécnica de aptidão a urbanização da área de expansão da UNICAMP. Para esse fim, mapas geológico, hidrológico, geomorfológico e de solos foram compilados, atualizados em campo e tratados pelo software GIS, ArcMap 10.7. A seguir a lógica fuzzy foi aplicada e as classes de aptidão a urbanização foram determinadas. Complementarmente se realizou ensaios geotécnicos nas classes de aptidão para melhor caracterização dessas e validação do mapeamento gerado pela lógica fuzzy. Foram definidas 6 classes de aptidão a urbanização, separando áreas propícias a ocupação, áreas com ocupação permitida se observando determinados critérios técnicos e áreas com restrição severa ou absoluta a urbanização, tais como áreas de preservação previstas pelas leis ambientais e ou de proteção dos recursos hídricos. A lógica fuzzy se mostrou um método eficiente para a diferenciação das classes de aptidão a urbanização.
- 2 February 2022
- Published by UNESP - Universidade Estadual Paulista in Geosciences = Geociências
- Vol. 40 (4) , 1137-1145
Open AccessLÓGICA FUZZY APLICADA A ELABORAÇÃO DE CARTA GEOTÉCNICA DE APTIDÃO À URBANIZAÇÃO DA ÁREA DE EXPANSÃO DA UNICAMP - CAMPINAS, SP
A necessidade de se planejar e direcionar o uso e ocupação do solo fez com que surgissem variados métodos para esse fim, dentre estes a cartografia geotécnica. A avaliação da aptidão de terrenos para urbanização tem sido tradicionalmente realizada pela cartografia geotécnica, sendo atualmente fortemente apoiada em ferramentas de geoprocessamento. A lógica fuzzy é um método matemático que pode ser aplicado como ferramenta de geoprocessamento para fins cartográficos quando se necessita realizar a análise integrada de diversos temas. Este estudo objetivou testar a aplicação da lógica fuzzy para elaboração de carta geotécnica de aptidão a urbanização da área de expansão da UNICAMP. Para esse fim, mapas geológico, hidrológico, geomorfológico e de solos foram compilados, atualizados em campo e tratados pelo software GIS, ArcMap 10.7. A seguir a lógica fuzzy foi aplicada e as classes de aptidão a urbanização foram determinadas. Complementarmente se realizou ensaios geotécnicos nas classes de aptidão para melhor caracterização dessas e validação do mapeamento gerado pela lógica fuzzy. Foram definidas 6 classes de aptidão a urbanização, separando áreas propícias a ocupação, áreas com ocupação permitida se observando determinados critérios técnicos e áreas com restrição severa ou absoluta a urbanização, tais como áreas de preservação previstas pelas leis ambientais e ou de proteção dos recursos hídricos. A lógica fuzzy se mostrou um método eficiente para a diferenciação das classes de aptidão a urbanização.
- Open Access
- 1 December 2020
- Published by Journal of Urban Technology and Sustainability in Journal of Urban Technology and Sustainability
- Vol. 3 (1) , 28-35
Caracterização de resíduos de construção e demolição para uso em engenharia civil
Resíduos de construção e demolição têm sido estudados por meios técnicos para desenvolver ferramentas de gestão para reduzir os impactos ambientais. Dentre essas, a reciclagem pode ser destacada. Este artigo demonstra a obtenção e avaliação de parâmetros de engenharia para resíduos de construção de concreto obtidos em uma usina de reciclagem de RCD próxima a São Paulo. Para tanto, foram realizados ensaios laboratoriais de acordo com as normas técnicas pertinentes para determinação das seguintes características: peso específico, integridade por ultrassom, resistência à compressão, módulo de elasticidade e absorção. Os parâmetros obtidos podem servir para melhor caracterizar os resíduos em estudo, bem como valores iniciais para o desenvolvimento de projetos básicos de engenharia civil com baixa responsabilidade estrutural.
- 1 December 2020
- Published by Journal of Urban Technology and Sustainability in Journal of Urban Technology and Sustainability
- Vol. 3 (1) , 28-35
Open AccessCaracterização de resíduos de construção e demolição para uso em engenharia civil
Resíduos de construção e demolição têm sido estudados por meios técnicos para desenvolver ferramentas de gestão para reduzir os impactos ambientais. Dentre essas, a reciclagem pode ser destacada. Este artigo demonstra a obtenção e avaliação de parâmetros de engenharia para resíduos de construção de concreto obtidos em uma usina de reciclagem de RCD próxima a São Paulo. Para tanto, foram realizados ensaios laboratoriais de acordo com as normas técnicas pertinentes para determinação das seguintes características: peso específico, integridade por ultrassom, resistência à compressão, módulo de elasticidade e absorção. Os parâmetros obtidos podem servir para melhor caracterizar os resíduos em estudo, bem como valores iniciais para o desenvolvimento de projetos básicos de engenharia civil com baixa responsabilidade estrutural.
- 15 May 2020
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 38 (12) , 1321-1330
Use of construction and demolition solid wastes for basket gabion filling
Construction and demolition wastes have been studied by technical means aiming at the development of management tools to reduce their environmental impacts. Among these, recycling can be highlighted. This paper aims at the technical assessment of basket gabions filled with construction and demolition solid waste. Gabions are usually used for retaining walls construction, and these are commonly filled with rocks. Retaining walls are essential for earthfill slopes stabilization, and they must have proper characteristics of strength. However, depending on the slope height or the technical responsibility of the retaining wall, alternative materials with proper characteristics could be used to fill the gabions. The use of recycled material for gabion filling could reduce environmental impacts and costs caused by retaining wall construction. So, basket gabion cells were filled with construction solid waste and basaltic rocks, both crushed into coarse granulometry aiming to compare technical characteristics among them. The performed laboratory tests showed that the horizontal and vertical displacements determined for gabion filled with wastes were near to those obtained for gabions filled with basaltic rocks for a retaining wall of 5 m and up. In conclusion, it can be drawn that basket gabions filled with construction and demolition waste may be a technical alternative for civil construction, reducing environmental impacts and raw material consumption for retaining wall execution.
- 15 May 2020
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 38 (12) , 1321-1330
Use of construction and demolition solid wastes for basket gabion filling
Construction and demolition wastes have been studied by technical means aiming at the development of management tools to reduce their environmental impacts. Among these, recycling can be highlighted. This paper aims at the technical assessment of basket gabions filled with construction and demolition solid waste. Gabions are usually used for retaining walls construction, and these are commonly filled with rocks. Retaining walls are essential for earthfill slopes stabilization, and they must have proper characteristics of strength. However, depending on the slope height or the technical responsibility of the retaining wall, alternative materials with proper characteristics could be used to fill the gabions. The use of recycled material for gabion filling could reduce environmental impacts and costs caused by retaining wall construction. So, basket gabion cells were filled with construction solid waste and basaltic rocks, both crushed into coarse granulometry aiming to compare technical characteristics among them. The performed laboratory tests showed that the horizontal and vertical displacements determined for gabion filled with wastes were near to those obtained for gabions filled with basaltic rocks for a retaining wall of 5 m and up. In conclusion, it can be drawn that basket gabions filled with construction and demolition waste may be a technical alternative for civil construction, reducing environmental impacts and raw material consumption for retaining wall execution.
- Open Access
- 1 June 2019
- Published by FapUNIFESP (SciELO) in Engenharia Agrícola
- Vol. 39 (3) , 370-379
WIND EFFECTS ON FOUNDATIONS OF SILOS AND LIGHT STRUCTURES: SOLUTION BY USE OF STEEL PILES IN DIABASIC SOIL
Wind solicitations generate horizontal, tensile, and compressive stresses on building foundations. In empty light structures, such as agricultural greenhouses and, in the specific case of silos and elevated structures such as metal water tanks, the consideration of these loads becomes important because the lack of the weight component due to the storage load significantly influences the balance of forces. This study focused on the behavior of metallic steel profiles, aiming at its application as a foundation element for the pile, considering the soil of Diabasic origin common to the Center-South region of Brazil. Load tests in real scale were carried out on three steel profiles, type I, gauge W 250 mm x 32.7 kg m-1, drilled in the ground up to 12m deep by means of a pile driver. One steel profile was submitted to lateral loading, another to vertical compressive loading, and the other to vertical tensile load. Test results determined the bearing load of the pile for each loading type, calculated the soil reaction coefficient for lateral loading, and verified the applicability of load capacity prediction methods to tensile and compressive strengths of piles, commonly used in foundation projects.
- 1 June 2019
- Published by FapUNIFESP (SciELO) in Engenharia Agrícola
- Vol. 39 (3) , 370-379
Open AccessWIND EFFECTS ON FOUNDATIONS OF SILOS AND LIGHT STRUCTURES: SOLUTION BY USE OF STEEL PILES IN DIABASIC SOIL
Wind solicitations generate horizontal, tensile, and compressive stresses on building foundations. In empty light structures, such as agricultural greenhouses and, in the specific case of silos and elevated structures such as metal water tanks, the consideration of these loads becomes important because the lack of the weight component due to the storage load significantly influences the balance of forces. This study focused on the behavior of metallic steel profiles, aiming at its application as a foundation element for the pile, considering the soil of Diabasic origin common to the Center-South region of Brazil. Load tests in real scale were carried out on three steel profiles, type I, gauge W 250 mm x 32.7 kg m-1, drilled in the ground up to 12m deep by means of a pile driver. One steel profile was submitted to lateral loading, another to vertical compressive loading, and the other to vertical tensile load. Test results determined the bearing load of the pile for each loading type, calculated the soil reaction coefficient for lateral loading, and verified the applicability of load capacity prediction methods to tensile and compressive strengths of piles, commonly used in foundation projects.
- 1 February 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 31 (2)
Behavior of Laterally Top-Loaded Deep Foundations in Highly Porous and Collapsible Soil
Problems associated with horizontal loading in foundation structures often occur when the surface soil has particular characteristics like the unsaturated, porous, and collapsible soils that are very common in Brazil. In the state of São Paulo, more precisely in the region of Campinas, the occurrence of such soils is detected in several places. For this reason, this work was conceived for the purpose of assessing the performance of four types of deep foundations subjected to horizontal loading via analysis of the load versus horizontal displacement curve and determination of the horizontal reaction coefficient of the soil ( ). To accomplish this, load tests were carried out with bored piles, continuous flight auger piles (CFA), steel piles, and belled caissons at the Experimental Site of Foundations at the State University of Campinas—Unicamp, Campinas, São Paulo, Brazil. The tests were performed under soil conditions of natural moisture and after 48 h of flooding. The results showed a large drop in parameters of soil resistance due to flooding—an approximately 50% drop on average for the ultimate load and 70% for the horizontal reaction coefficient of the soil.- 1 February 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 31 (2)
Behavior of Laterally Top-Loaded Deep Foundations in Highly Porous and Collapsible Soil
Problems associated with horizontal loading in foundation structures often occur when the surface soil has particular characteristics like the unsaturated, porous, and collapsible soils that are very common in Brazil. In the state of São Paulo, more precisely in the region of Campinas, the occurrence of such soils is detected in several places. For this reason, this work was conceived for the purpose of assessing the performance of four types of deep foundations subjected to horizontal loading via analysis of the load versus horizontal displacement curve and determination of the horizontal reaction coefficient of the soil ( ). To accomplish this, load tests were carried out with bored piles, continuous flight auger piles (CFA), steel piles, and belled caissons at the Experimental Site of Foundations at the State University of Campinas—Unicamp, Campinas, São Paulo, Brazil. The tests were performed under soil conditions of natural moisture and after 48 h of flooding. The results showed a large drop in parameters of soil resistance due to flooding—an approximately 50% drop on average for the ultimate load and 70% for the horizontal reaction coefficient of the soil.- Open Access
- 19 December 2018
- Published by USCS Universidade Municipal de Sao Caetano do Sul in Gestão & Regionalidade
- Vol. 34 (102)
DIAGNÓSTICO DO PROGRAMA DE COLETA SELETIVA NA ZONA LESTE NA CIDADE DE SÃO PAULO SOB A ÓTICA DAS COOPERATIVAS, PODER PÚBLICO E MUNÍCIPES
Este trabalho identifica a visão de gestor público, líderes de cooperativas de reciclagem e munícipes acerca da coleta seletiva na Zona Leste de São Paulo, de forma a entender dificuldades enfrentadas pelos envolvidos, bem como causas que justificam os baixos volumes de material coletado. Para a obtenção dos dados foram efetuadas entrevistas, que foram gravadas e, posteriormente, transcritas. Foram entrevistados: um representante da prefeitura ligado a programas de coleta seletiva, dois líderes de Cooperativas de Material Reciclável atuantes na Zona Leste e 10 munícipes. Osresultados demonstraram que o programa de coleta seletiva na cidade de São Paulo ainda é falho; já que nem o poder público, nem as cooperativas e; muito menos a população; estão satisfeitos e apontaram diversas falhas.
- 19 December 2018
- Published by USCS Universidade Municipal de Sao Caetano do Sul in Gestão & Regionalidade
- Vol. 34 (102)
Open AccessDIAGNÓSTICO DO PROGRAMA DE COLETA SELETIVA NA ZONA LESTE NA CIDADE DE SÃO PAULO SOB A ÓTICA DAS COOPERATIVAS, PODER PÚBLICO E MUNÍCIPES
Este trabalho identifica a visão de gestor público, líderes de cooperativas de reciclagem e munícipes acerca da coleta seletiva na Zona Leste de São Paulo, de forma a entender dificuldades enfrentadas pelos envolvidos, bem como causas que justificam os baixos volumes de material coletado. Para a obtenção dos dados foram efetuadas entrevistas, que foram gravadas e, posteriormente, transcritas. Foram entrevistados: um representante da prefeitura ligado a programas de coleta seletiva, dois líderes de Cooperativas de Material Reciclável atuantes na Zona Leste e 10 munícipes. Osresultados demonstraram que o programa de coleta seletiva na cidade de São Paulo ainda é falho; já que nem o poder público, nem as cooperativas e; muito menos a população; estão satisfeitos e apontaram diversas falhas.
- 28 August 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 753, 285-289
Effect of Second Loading on the Instrumented Continuous Flight Auger Concrete Pile on Porous Soil
This paper presents the results of two load tests carried out in a continuous flight auger pile of 0.4 m in diameter and 12 m in length. The pile was instrumented in depth with strain gages in order to obtain the load capacity along the shaft and the tip. The load tests were carried out at the University of Campinas Experimental Site Test. The subsoil where the pile was installed is constituted by a first stratum of Silty Clay, which is porous and collapsible, of 6.5 m in thickness, followed by a stratum of residual soil of Clayey Silt up to 14 m depth. The first load test was the slow type, and a quick load test in the same pile after five days. From the results obtained with the use of instrumentation, the values for both lateral and tip load were determined in each one of test carried out in the pile studied. With these results and applying the Cambefort’s Law, it was could evaluate the evolution of the shaft friction and tip load in relation to the associated settlements, as well as the occurrence of residual load. The ultimate load obtained in the test was 960 kN and 810 kN for the first and second tests, respectively. The stress for the tip was 853 kPa and 655 kPa for the first and second tests, respectively.
- 28 August 2017
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 753, 285-289
Effect of Second Loading on the Instrumented Continuous Flight Auger Concrete Pile on Porous Soil
This paper presents the results of two load tests carried out in a continuous flight auger pile of 0.4 m in diameter and 12 m in length. The pile was instrumented in depth with strain gages in order to obtain the load capacity along the shaft and the tip. The load tests were carried out at the University of Campinas Experimental Site Test. The subsoil where the pile was installed is constituted by a first stratum of Silty Clay, which is porous and collapsible, of 6.5 m in thickness, followed by a stratum of residual soil of Clayey Silt up to 14 m depth. The first load test was the slow type, and a quick load test in the same pile after five days. From the results obtained with the use of instrumentation, the values for both lateral and tip load were determined in each one of test carried out in the pile studied. With these results and applying the Cambefort’s Law, it was could evaluate the evolution of the shaft friction and tip load in relation to the associated settlements, as well as the occurrence of residual load. The ultimate load obtained in the test was 960 kN and 810 kN for the first and second tests, respectively. The stress for the tip was 853 kPa and 655 kPa for the first and second tests, respectively.