Amin Vosoughi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Amin Vosoughi has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Maziar Hakim
Department of Chemical and Petroleum Engineering, Sharif University of Technology, Tehran, Iran
2 shared publications Amin Delparish
Department of Chemical and Petroleum Engineering, Sharif University of Technology, Tehran, Iran
1 shared publicationFatemeh Yazdian
Research Center for New Technologies in Life Science Engineering, University of Tehran, P.O. Box 14395-1374, Tehran, Iran; Department of Life Science Engineering, Faculty of New Sciences and Technologies, University of Tehran, P.O. Box 14395-1561, Tehran, Iran
1 shared publication- Ghassem Amoabediny
School of Chemical Engineering, College of Engineering, University of Tehran, Tehran, Iran
1 shared publication - Gholamreza Pazuki
Department of Chemical Engineering, Amirkabir University of Technology (Tehran Polytechnic), Tehran, Iran
1 shared publication Gita Behmardikalantari
1 shared publication
Latest Publications
- Open Access
- 1 September 2018
- Published by Wiley in Bioengineering & Translational Medicine
- Vol. 3 (3) , 265-274
Encapsulation of mesenchymal stem cells in glycosaminoglycans‐chitosan polyelectrolyte microcapsules using electrospraying technique: Investigating capsule morphology and cell viability
Polyelectrolyte microcapsules are modular constructs which facilitate cell handling and assembly of cell‐based tissue constructs. In this study, an electrospray (ES) encapsulation apparatus was developed for the encapsulation of mesenchymal stem cells (MSCs). Ionic complexation between glycosaminoglycans (GAGs) and chitosan formed a polyelectrolyte complex membrane at the interface. To optimize the capsules, the effect of voltage, needle size and GAG formulation on capsule size were investigated. It was observed that by increasing the voltage and decreasing the needle size, the capsule size would decrease but at voltages above 12 kV, capsule size distribution broadened significantly which yields lower circularity. Increase in GAG viscosity resulted in larger microcapsules and cell viability exhibited no significant changes during the encapsulation procedure. These results suggest that ES is a highly efficient, and scalable approach to the encapsulation of MSCs for subsequent use in bioprinting and other modular tissue engineering or regenerative medicine applications.
- 1 September 2018
- Published by Wiley in Bioengineering & Translational Medicine
- Vol. 3 (3) , 265-274
Open AccessEncapsulation of mesenchymal stem cells in glycosaminoglycans‐chitosan polyelectrolyte microcapsules using electrospraying technique: Investigating capsule morphology and cell viability
Polyelectrolyte microcapsules are modular constructs which facilitate cell handling and assembly of cell‐based tissue constructs. In this study, an electrospray (ES) encapsulation apparatus was developed for the encapsulation of mesenchymal stem cells (MSCs). Ionic complexation between glycosaminoglycans (GAGs) and chitosan formed a polyelectrolyte complex membrane at the interface. To optimize the capsules, the effect of voltage, needle size and GAG formulation on capsule size were investigated. It was observed that by increasing the voltage and decreasing the needle size, the capsule size would decrease but at voltages above 12 kV, capsule size distribution broadened significantly which yields lower circularity. Increase in GAG viscosity resulted in larger microcapsules and cell viability exhibited no significant changes during the encapsulation procedure. These results suggest that ES is a highly efficient, and scalable approach to the encapsulation of MSCs for subsequent use in bioprinting and other modular tissue engineering or regenerative medicine applications.
- 1 May 2015
- Published by Elsevier in Fluid Phase Equilibria
- Vol. 394, 140-147
Prediction of liquid–liquid equilibrium behavior for aliphatic+aromatic+ionic liquid using two different neural network-based models
- 1 May 2015
- Published by Elsevier in Fluid Phase Equilibria
- Vol. 394, 140-147
Prediction of liquid–liquid equilibrium behavior for aliphatic+aromatic+ionic liquid using two different neural network-based models
- 19 January 2015
- Published by IWA Publishing in Water Science & Technology
- Vol. 71 (6) , 823-831
Optimization of operating parameters for efficient photocatalytic inactivation of Escherichia coli based on a statistical design of experiments
In this work, the individual and interaction effects of three key operating parameters of the photocatalytic disinfection process were evaluated and optimized using response surface methodology (RSM) for the first time. The chosen operating parameters were: reaction temperature, initial pH of the reaction mixture and TiO2 P-25 photocatalyst loading. Escherichia coli concentration, after 90 minutes irradiation of UV-A light, was selected as the response. Twenty sets of photocatalytic disinfection experiments were conducted by adjusting operating parameters at five levels using the central composite design. Based on the experimental data, a semi-empirical expression was established and applied to predict the response. Analysis of variance revealed a strong correlation between predicted and experimental values of the response. The optimum values of the reaction temperature, initial pH of the reaction mixture and photocatalyst loading were found to be 40.3 °C, 5.9 g/L, and 1.0 g/L, respectively. Under the optimized conditions, E. coli concentration was observed to reduce from 107 to about 11 CFU/mL during the photocatalytic process. Moreover, all these results showed the great significance of the RSM in developing high performance processes for photocatalytic water disinfection.
- 19 January 2015
- Published by IWA Publishing in Water Science & Technology
- Vol. 71 (6) , 823-831
Optimization of operating parameters for efficient photocatalytic inactivation of Escherichia coli based on a statistical design of experiments
In this work, the individual and interaction effects of three key operating parameters of the photocatalytic disinfection process were evaluated and optimized using response surface methodology (RSM) for the first time. The chosen operating parameters were: reaction temperature, initial pH of the reaction mixture and TiO2 P-25 photocatalyst loading. Escherichia coli concentration, after 90 minutes irradiation of UV-A light, was selected as the response. Twenty sets of photocatalytic disinfection experiments were conducted by adjusting operating parameters at five levels using the central composite design. Based on the experimental data, a semi-empirical expression was established and applied to predict the response. Analysis of variance revealed a strong correlation between predicted and experimental values of the response. The optimum values of the reaction temperature, initial pH of the reaction mixture and photocatalyst loading were found to be 40.3 °C, 5.9 g/L, and 1.0 g/L, respectively. Under the optimized conditions, E. coli concentration was observed to reduce from 107 to about 11 CFU/mL during the photocatalytic process. Moreover, all these results showed the great significance of the RSM in developing high performance processes for photocatalytic water disinfection.