Nel Samama
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Nel Samama has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Muriel Muller
SAMOVAR, Tlcom SudParis, Institut Polytechnique de Paris, Palaiseau, France
3 shared publications - Alexandre Vervisch-Picois
Navigation Group of the Department of Electronics and Physics, Palaiseau, France
2 shared publications - Jean-Christophe Cousin
TELECOM ParisTech, France
2 shared publications - Jose Rubio-Hernan
SAMOVAR, Télécom SudParis, CNRS, Université Paris-Saclay
2 shared publications Thierry Taillandier-Loize
Institut Polytechnique de Paris
2 shared publicationsA. Patarot
1 shared publication
Latest Publications
- 10 August 2025
- Published by Springer Nature
- p. 618-630
Antenna Structures for Resolving Ambiguities in the Dual-Antenna Approach and Measuring Phase Differences
- 10 August 2025
- Published by Springer Nature
- p. 618-630
Antenna Structures for Resolving Ambiguities in the Dual-Antenna Approach and Measuring Phase Differences
- 10 August 2025
- Published by Springer Nature
- p. 631-643
Symbolic Indoor Positioning as Part of a Light Infrastructure: Usefulness and Principle
- 10 August 2025
- Published by Springer Nature
- p. 631-643
Symbolic Indoor Positioning as Part of a Light Infrastructure: Usefulness and Principle
- 7 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
2-D Indoor Localization Resolution Improvement Using IR-UWB Stepped Frequencies Signals
This article discusses the ability to improve the resolution of range and azimuth angle measurements by an interferometric localization system used to locate beacons within its line of sight (LoS) by exploiting stepped frequency signals Impulse Radio - Ultra WideBand (IR-UWB) centered on 2 frequencies. This improvement does not require increasing the frequency bandwidth used. This solution uses a phase correlation (PC) method, usually applied to continuous wave (CW) signals, adapted to Ultra WideBand (UWB) pulse signals. The results obtained are compared with those computed by a classical method of energy detection (ED) by exploiting the same frequency band.
- 7 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
2-D Indoor Localization Resolution Improvement Using IR-UWB Stepped Frequencies Signals
This article discusses the ability to improve the resolution of range and azimuth angle measurements by an interferometric localization system used to locate beacons within its line of sight (LoS) by exploiting stepped frequency signals Impulse Radio - Ultra WideBand (IR-UWB) centered on 2 frequencies. This improvement does not require increasing the frequency bandwidth used. This solution uses a phase correlation (PC) method, usually applied to continuous wave (CW) signals, adapted to Ultra WideBand (UWB) pulse signals. The results obtained are compared with those computed by a classical method of energy detection (ED) by exploiting the same frequency band.
- Open Access
- 4 May 2023
- Published by MDPI AG in Future Transportation
- Vol. 3 (2) , 568-583
Advanced Smartphone-Based Identification of Transport Modes: Resilience under GNSS-Based Attacks
One of the main challenges for ticketing in Mobility as a Service is the integration of the public and individual transport modes into a unified ticketing service. To realize this concept, a trustworthy identification of transport modes that is resilient to possible attacks is required. In this work, we propose two smartphone-based methods to seamlessly identify the use of trams, buses, subways, walking and bicycles, which are able to detect GNSS-based attacks and continue to provide a trustworthy identification of transport modes. We have recorded real-world measurements with commercial smartphones using the transport network in Munich and Paris. Our results show that it is possible to provide trustworthy identification of transport modes even when the system is under attack. In conclusion, in this work we demonstrate the vulnerability of smartphone-based ticketing to GNSS-based attacks, propose two methods to overcome this vulnerability and demonstrate the validity of our methods with real-world measurements.
- 4 May 2023
- Published by MDPI AG in Future Transportation
- Vol. 3 (2) , 568-583
Open AccessAdvanced Smartphone-Based Identification of Transport Modes: Resilience under GNSS-Based Attacks
One of the main challenges for ticketing in Mobility as a Service is the integration of the public and individual transport modes into a unified ticketing service. To realize this concept, a trustworthy identification of transport modes that is resilient to possible attacks is required. In this work, we propose two smartphone-based methods to seamlessly identify the use of trams, buses, subways, walking and bicycles, which are able to detect GNSS-based attacks and continue to provide a trustworthy identification of transport modes. We have recorded real-world measurements with commercial smartphones using the transport network in Munich and Paris. Our results show that it is possible to provide trustworthy identification of transport modes even when the system is under attack. In conclusion, in this work we demonstrate the vulnerability of smartphone-based ticketing to GNSS-based attacks, propose two methods to overcome this vulnerability and demonstrate the validity of our methods with real-world measurements.
- Open Access
Characterization of the Ability of Low-Cost GNSS Receiver to Detect Spoofing Using Clock Bias
The aim of this paper was to propose a method to characterize the ability of a GNSS user to detect a spoofing attack from the behavior of the clock bias. Spoofing interference is not a new issue, especially in military GNSS, although it is a new challenge for civil GNSS, since it is currently implemented and used in many everyday applications. For this reason, it is still a topical issue, especially for receivers that only have access to high-level data (PVT,CN0). To address this important issue, after conducting a study of the receiver clock polarization calculation process, this led to the development of a very basic Matlab model that emulates a spoofing attack at the computational level. Using this model, we were able to observe that the clock bias is affected by the attack. However, the amplitude of this disturbance depends on two factors: the distance between the spoofer and the target and the synchronization between the clock that generates the spoofing signal and the reference clock of the constellation. To validate this observation, more or less synchronized spoofing attacks were carried out on a fixed commercial GNSS receiver with the use of GNSS signal simulators and also with a moving target. We propose then a method to characterize the capacity of detecting a spoofing attack with the clock bias behavior. We present the application of this method for two commercial receivers of the same manufacturer from different generations.
Open AccessCharacterization of the Ability of Low-Cost GNSS Receiver to Detect Spoofing Using Clock Bias
The aim of this paper was to propose a method to characterize the ability of a GNSS user to detect a spoofing attack from the behavior of the clock bias. Spoofing interference is not a new issue, especially in military GNSS, although it is a new challenge for civil GNSS, since it is currently implemented and used in many everyday applications. For this reason, it is still a topical issue, especially for receivers that only have access to high-level data (PVT,CN0). To address this important issue, after conducting a study of the receiver clock polarization calculation process, this led to the development of a very basic Matlab model that emulates a spoofing attack at the computational level. Using this model, we were able to observe that the clock bias is affected by the attack. However, the amplitude of this disturbance depends on two factors: the distance between the spoofer and the target and the synchronization between the clock that generates the spoofing signal and the reference clock of the constellation. To validate this observation, more or less synchronized spoofing attacks were carried out on a fixed commercial GNSS receiver with the use of GNSS signal simulators and also with a moving target. We propose then a method to characterize the capacity of detecting a spoofing attack with the clock bias behavior. We present the application of this method for two commercial receivers of the same manufacturer from different generations.
- 27 February 2023
- Published by Springer Nature
- p. 696-714
A Symbolic GeoPositioning System to Allow e-Health Enhanced Usages
- 27 February 2023
- Published by Springer Nature
- p. 696-714
A Symbolic GeoPositioning System to Allow e-Health Enhanced Usages
- Open Access
An IoT-Based GeoData Production System Deployed in a Hospital
Navigation in large hospitals remains a challenge, especially for patients, visitors and, in some cases, for staff, but in particular it is notable in the case of tracking ambulatory equipment. Current techniques generally seek to reproduce what outdoor navigation systems provide, i.e., “good” accuracy. In many cases, especially in hospitals, reliability is much more important than accuracy. We show that it is possible to realize a simple, reliable system with a low accuracy, but which perfectly fulfills the task assigned in the particular case of tracking stretchers. Optimizing the use of hospital equipment requires the knowledge of its movement. The possibility to access equipment location in real time as well as on the knowledge of the time necessary to move it between two locations allows to predict or to estimate the load and possibly to scale the necessary number of stretchers, and thus the availability of the stretcher bearers. In this paper, an approach of the real-time location of these devices is proposed, and it is called “symbolic”. The principle is described, as well as the practical implementation and the data that can be retrieved. In the second part, an analysis of the results obtained is provided in two directions: the location of stretchers and the determination of travel times. The methodology followed is described, and it is shown that a correct positioning rate of 90% is reached, which is slightly lower than expected, explained by the chosen practical implementation. Moreover, the average error on the determination of travel times is approximately ten seconds on 2 to 7 min trips. The “reliability” (the terminology of which is discussed at the end of the paper) of the results is related to the simplicity of the approach.
Open AccessAn IoT-Based GeoData Production System Deployed in a Hospital
Navigation in large hospitals remains a challenge, especially for patients, visitors and, in some cases, for staff, but in particular it is notable in the case of tracking ambulatory equipment. Current techniques generally seek to reproduce what outdoor navigation systems provide, i.e., “good” accuracy. In many cases, especially in hospitals, reliability is much more important than accuracy. We show that it is possible to realize a simple, reliable system with a low accuracy, but which perfectly fulfills the task assigned in the particular case of tracking stretchers. Optimizing the use of hospital equipment requires the knowledge of its movement. The possibility to access equipment location in real time as well as on the knowledge of the time necessary to move it between two locations allows to predict or to estimate the load and possibly to scale the necessary number of stretchers, and thus the availability of the stretcher bearers. In this paper, an approach of the real-time location of these devices is proposed, and it is called “symbolic”. The principle is described, as well as the practical implementation and the data that can be retrieved. In the second part, an analysis of the results obtained is provided in two directions: the location of stretchers and the determination of travel times. The methodology followed is described, and it is shown that a correct positioning rate of 90% is reached, which is slightly lower than expected, explained by the chosen practical implementation. Moreover, the average error on the determination of travel times is approximately ten seconds on 2 to 7 min trips. The “reliability” (the terminology of which is discussed at the end of the paper) of the results is related to the simplicity of the approach.
- 31 October 2021
- Published by Springer Nature
- p. 215-227
Overall Feasibility of RF Energy Harvesting for IoT
- 31 October 2021
- Published by Springer Nature
- p. 215-227
Overall Feasibility of RF Energy Harvesting for IoT
- Open Access
- 10 June 2020
- Published by Hindawi Limited in Journal of Sensors
- Vol. 2020, 1-8
Improvement of the Angle of Arrival Measurement Accuracy for Indoor UWB Localization
This paper shows that the accuracy of azimuth angle measurement for an interferometric localization system used to locate tags in its Line-of-Sight (LoS) can be improved by exploiting Impulse Radio-Ultra WideBand (IR-UWB) signals and without increasing the frequency bandwidth. This solution uses a Phase Correlation (PC) method, initially applied for Continuous Wave (CW) signals, adapted for Ultra WideBand (UWB) pulse signals. The obtained results are compared to those computed by a classical Energy Detection (ED) method where it becomes impossible to estimate azimuth angles for tag positions close to the orthogonal centered axis of the localization system baseline.
- 10 June 2020
- Published by Hindawi Limited in Journal of Sensors
- Vol. 2020, 1-8
Open AccessImprovement of the Angle of Arrival Measurement Accuracy for Indoor UWB Localization
This paper shows that the accuracy of azimuth angle measurement for an interferometric localization system used to locate tags in its Line-of-Sight (LoS) can be improved by exploiting Impulse Radio-Ultra WideBand (IR-UWB) signals and without increasing the frequency bandwidth. This solution uses a Phase Correlation (PC) method, initially applied for Continuous Wave (CW) signals, adapted for Ultra WideBand (UWB) pulse signals. The obtained results are compared to those computed by a classical Energy Detection (ED) method where it becomes impossible to estimate azimuth angles for tag positions close to the orthogonal centered axis of the localization system baseline.