KRK. Sai Madhukar Reddy

K. Sai Madhukar Reddy

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


K. Sai Madhukar Reddy has a total of 47 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Magnetic ordering in 45 nm-diameter multisegmented FeGa/Cu nanowires: single nanowires and arrays

    by Eduardo Ortega, Sai Madhukar Reddy, Israel Betancourt, Sina Roughani, Bethanie J. H. Stadler, Arturo Ponce

    Magnetic nanowires are ideal candidates for many diverse applications, such as 3D magnetic memory and bio-barcodes, they also allow fundamental studies of magnetic interactions at the nanometer level. Usually their magnetic characterization involves hysteresis loops that represent the weighted averages of each entire array. Here, off-axis electron holography under Lorentz microscopy conditions has been used to observe the magnetization distribution and to determine the saturation magnetization (Ms = 1.26 × 106 A m−1) of a single 45 nm diameter FeGa(10.5 nm)/Cu(6.5 nm) nanowire. In addition, a row of segmented nanowires still within the alumina growth template was carefully sliced from the array to observe the magnetization distribution resulting from interwire as well as intersegment interactions. Two simultaneous magnetic states were observed in this novel experimental configuration: one is the antiferromagnetic ordering of segments along each wire with ferromagnetic ordering between nanowires and the second is the presence of ferromagnetic vortices along nanowire lengths. Simulations have been performed to verify the presence of both remnant states. These states demonstrate the frustration present in hexagonally packed nanowires and demonstrate the necessity to understand long range magnetic ordering for applications such as 3D magnetic memory.


  • Metallic 10 nm Diameter Magnetic Sensors and Large-Scale Ordered Arrays

    by Sang-Yeob Sung, Mazin M. Maqableh, Xiaobo Huang, K. Sai Madhukar Reddy, R. H. Victora, Bethanie J. H. Stadler

    Metallic nanowires with low resistivity were grown inside insulating aluminum oxide matrices that contained very uniform columnar nanopores (10.6+/1.7 nm diameters). These nanopores can be made with large-scale order (cm 2 ), which is desirable in applications such as hard drive read sensors and random access memories. The nanowires are grown by electrochemical deposition directly inside the alumina to avoid sidewall damage compared to nanostructures that are defined from films by lithographical patterning and etching. Specifically, trilayers of [Co(15 nm)/Cu(5 nm)/Co(10 nm)] were synthesized and measured to have 30 Ω resistance and 19% magnetoresistance. These parameters are desirable for read head sensors, especially because the nanowires described here have 1:1 aspect ratios, and 10× smaller areas and 100× lower resistances than conventional read sensors based on lithographically produced magnetic tunnel junctions. A new nanostamping technique is introduced, in which linear stamps with ordered cm 2 areas are imprinted onto aluminum precursors to produce ordered nanoporous aluminum oxide upon anodization. These stamps are substantially less-time consuming and cheaper to make than dot type stamps, and the order enables closely spaced arrays of CPP-GMR sensors for one-pass 2-D recording and cross recording. Importantly, the GMR sensors are grown directly into aluminum oxide with 20 nm separation. Therefore, a relatively large pattern (30 × 100 nm) can be used to produce three 10 nm-diameter GMR sensors without roughening or redeposition on sidewalls. The sensors are also already embedded in alumina for subsequent device processing.


  • Technique for measurement of magnetostriction in an individual nanowire using atomic force microscopy

    by Jung Jin Park, Eliot C. Estrine, Sai Madhukar Reddy, Bethanie J. H. Stadler, Alison B. Flatau

    We have investigated a method for measuring the dimensions of an individual multilayered Fe-Ga/Cu nanowire (NW) as it changes with induced magnetization. In this study, we demonstrate the proposed approach and establish this as a viable method for measuring the magnetostrictive behavior of an individual Fe-Ga/Cu NW using atomic force microscopy (AFM). When an external magnetic field (∼300 Oe) was applied perpendicular to the NW axis, the NW length appeared minimized. When a field (∼1000 Oe) was applied parallel to the NW axis, the height profile of the NW was found to be higher than in the case with no parallel external field. Since both ends of the NW were welded to the substrate, the magnetic field induced dimensional change of the NW caused deflection of the NW in the upward direction, which was significant enough to be detected by AFM. An average height difference of 15 nm was measured with and without an applied field which was then used to calculate the magnetostriction of the multilayered NW.


  • Hysteresis measurement of individual multilayered Fe-Ga/Cu nanowires using magnetic force microscopy

    by Jung Jin Park, Madhukar Reddy, Bethanie J. H. Stadler, Alison B. Flatau

    We have investigated nano-scale magnetic structures to learn how magnetic behaviors differ from what is observed in bulk materials. In this study, we have measured the magnetic hysteresis of individual multilayered nanowire using a magnetic force microscopy (MFM). The nanowires were composed of low-aspect ratio segments of iron-gallium (Galfenol, Fe80Ga20) and copper layers. Individual wires were released from nano-porous anodized aluminum oxide (AAO) templates and separated from other nanowires to avoid significant interactions between nearby nanowires. In this experiment, structures with aspects ratios c/a of ∼3 were studied. Different MFM phase magnitudes in response to the interaction of magnetic film coated MFM tips and Fe-Ga/Cu nanowire were observed as a function of applied external magnetic field (−850 Oe < H < 850 Oe). Amplitude differences between bright and dark responses in MFM images were used to demonstrate hysteresis. Coercivity measured was about 125 Oe, which is almost same as the coercivity value (∼150 Oe) of a nanowire array measured with a vibrating sample magnetometer (VSM). When fields are applied perpendicular to the nanowires, the hysteresis loops sheared, indicating that the easy axis is along the nanowire axis. Remanence magnetizations of an individual nanowire and a nanowire array were compared to demonstrate inter-wire magnetostatic dipolar interaction.


  • Low-Resistivity 10 nm Diameter Magnetic Sensors

    by Mazin M. Maqableh, Xiaobo Huang, Sang-Yeob Sung, K. Sai Madhukar Reddy, Gregory Norby, R. H. Victora, Bethanie J. H. Stadler

    Resistivities of 5.4 μΩ·cm were measured in 10-nm-diameter metallic wires. Low resistance is important for interconnections of the future to prevent heating, electromigration, high power consumption, and long RC time constants. To demonstrate application of these wires, Co/Cu/Co magnetic sensors were synthesized with 20–30 Ω and 19% magnetoresistance. Compared to conventional lithographically produced magnetic tunnel junction sensors, these structures offer facile fabrication and over 2 orders of magnitude lower resistances due to smooth sidewalls from in situ templated chemical growth.


  • Open Access

    Magnetization reversal mechanisms in 35-nm diameter Fe1-xGax/Cu multilayered nanowires

    by Sai Madhukar Reddy, Jung Jin Park, Mazin M. Maqableh, Alison B. Flatau, Bethanie J. H. Stadler

    In this work, magnetization reversal mechanisms in various 35 nm diameter Fe80Ga20/Cu multilayered nanowire arrays were studied by a vibrating sample magnetometer (VSM) equipped with vector coils, making it possible to monitor both x- and y-components of the sample moment during reversal. When reversal fields were applied in the low angular range (0 – 60°), all nanowire structures, irrespective of Fe80Ga20 or Cu aspect ratios, experienced reversal by nucleation and propagation of a vortex domain wall. However, when fields were applied in the high angular range of 60–90°, reversal occurred by coherent rotation. Using vector-VSM, it was further shown that in structures with pancake-like Fe80Ga20 segments, the extent to which moments in adjacent segments rotate cooperatively decreased as the Cu thickness increased.


  • Epitaxial Fe(1−x)Gax/GaAs structures via electrochemistry for spintronics applications

    by K. Sai Madhukar Reddy, Mazin M. Maqableh, Bethanie J. H. Stadler

    In this study, thin films of Fe83Ga17 (a giant magnetostrictive alloy) were grown on single-crystalline n-GaAs (001) and polycrystalline brass substrates via electrochemical synthesis from ferrous and gallium sulfate electrolytes. Extensive structural characterization using microdiffraction, high-resolution ω − 2θ, and rocking-curve analysis revealed that the films grown on GaAs(001) are highly textured with ⟨001⟩ orientation along the substrate normal, and the texture improved further upon annealing at 300 °C for 2 h in N2 environment. On the contrary, films grown on brass substrates exhibited ⟨011⟩ preferred orientation. Rocking-curve analysis done on Fe83Ga17/GaAs structures further confirmed that the ⟨001⟩ texture in the Fe83Ga17 thin film is a result of epitaxial nucleation and growth. The non-linear current−voltage plot obtained for the Fe−Ga/GaAs Schottky contacts was characteristic of tunneling injection, and showed improved behavior with annealing. Thus, this study demonstrates the feasibility of fabricating spintronic devices that incorporate highly magnetostrictive Fe(1−x)Gax thin films grown epitaxially via electrochemistry.


  • Controlled electrochemical deposition of magnetostrictive Fe1−xGax alloys

    by K. Sai Madhukar Reddy, Eliot C. Estrine, Dong-Ha Lim, William H. Smyrl, Bethanie J.H. Stadler


  • Electrochemical Synthesis of Magnetostrictive Fe–Ga/Cu Multilayered Nanowire Arrays with Tailored Magnetic Response

    by Sai Madhukar Reddy, Jung Jin Park, Suok‐Min Na, Mazin M. Maqableh, Alison B. Flatau, Bethanie J. H. Stadler

    Arrays of nanowires are fabricated with alternating segments of the magnetostrictive alloy Fe1–xGax and Cu using electrochemical deposition in nanoporous anodic aluminium oxide (AAO) templates. The difficult nature of Ga‐alloy electrochemistry is overcome by controlling mass‐transfer and hydrodynamic conditions using novel rotating disk electrode templates to obtain highly uniform segment lengths throughout the arrays. Extensive structural characterization by XRD, EBSD and TEM reveals a strong textured Fe1–xGax growth. Furthermore, using vibrating sample magnetometry (VSM), we demonstrate that control of magnetization reversal processes is possible once uniform aspect ratios are obtained for both the Fe–Ga and Cu segments.


  • Characterization of the magnetic properties of multilayer magnetostrictive iron-gallium nanowires

    by Jung Jin Park, Madhukar Reddy, Chaitanya Mudivarthi, Patrick R. Downey, Bethanie J. H. Stadler, Alison B. Flatau

    We investigate the magnetic properties of magnetostrictive iron-gallium (Galfenol, Fe100−xGax , 10≤x≤25 at. % ) nanowires with magnetic force microscopy (MFM) and using micromagnetic modeling software (magpar). Wires with diameters of 150 nm were fabricated in alternating multilayered structures with Fe-Ga and Cu having aspect ratios of ∼2 and ∼0.5 , respectively, with the goal of minimizing the relative contribution of shape anisotropy to magnetic domain alignment. Micromagnetic simulations of isolated Fe-Ga segments with these dimensions predict that (1) at remanence, two opposing vortex structures will form at the ends of a Fe-Ga segment, with a single domain wall in the middle of the segment and (2) traditional magnetic dipoles will form at the ends of the segment to align with a large (saturation) external magnetic field. MFM results are presented that support these models. At remanence, no contrast is observed in the MFM phase images. Magnetic poles become evident at the ends of the Fe-Ga segments when a magnetic field exceeding ∼300 Oe is applied along the length of the nanowire. The direction of the pole alignment is readily flipped by changing the direction of applied field by 180°. Additionally, MFM images show rotation of the magnetic poles in each Fe-Ga segment as they align with fields of ∼550 Oe applied at angles of ∼55° and ∼105° relative to the length of the nanowire. The MFM results support the simulation results and demonstrate that an aspect ratio of ∼2 will reduce shape anisotropy effects sufficiently in Fe-Ga nanowire that magnetization can lie off of the nanowire axis.