Akash Subhash Awale
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Akash Subhash Awale has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Abhimanyu Chaudhari
Department of Mechanical Engineering, Indian Institute of Technology (BHU), Varanasi, India
3 shared publications Meghanshu Vashista
Indian Institute of Technology Varanasi
3 shared publications- Meghanshu Vashista
I.I.T.(BHU)
3 shared publications - Mohd Zaheer Khan Yusufzai
Department of Mechanical Engineering, Indian Institute of Technology (BHU) Varanasi, Uttar Pradesh, India
3 shared publications - Ashwani Sharma
Department of Mechanical Engineering, Indian Institute of Technology (BHU), Varanasi, India
2 shared publications Kamal Kishore
School of Mechanical Engineering, Shandong University of Technology, Zibo, China
2 shared publications
Latest Publications
- 19 October 2025
- Published by Springer Nature
- p. 179-191
The Evaluation of Mechanical and Magnetic Properties of Hot Die Steel After Sustainable Grinding Using Barkhausen Emission Technique
- 19 October 2025
- Published by Springer Nature
- p. 179-191
The Evaluation of Mechanical and Magnetic Properties of Hot Die Steel After Sustainable Grinding Using Barkhausen Emission Technique
- 9 May 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (5-6) , 2065-2082
Investigation of biodegradable oil–based MQL parameters for sustainable grinding of H13 die steel using MCDM techniques
- 9 May 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (5-6) , 2065-2082
Investigation of biodegradable oil–based MQL parameters for sustainable grinding of H13 die steel using MCDM techniques
- 22 June 2022
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 144 (11) , 1-32
Modeling and Simulation Study of Dry Ultrasonic Vibration-Assisted Grinding of Tool Steel With Single Alumina Abrasive Grit
In the precision fabrication industries, ultrasonic vibration-assisted grinding is widely utilized for the finishing of “difficult-to-cut” materials due to its intermittent cutting mechanism and brittle-to-ductile mode machining. In this study, a two-dimensional finite element model (FEM) of single grit ultrasonic vibration-assisted dry grinding (UVADG) and conventional dry grinding (CDG) of AISI D2 steel has been developed, which taken into account the influence of longitudinal ultrasonic vibration on the workpiece with variable downfeed. The effects of ultrasonic vibration and downfeed on the chip formation mechanism, temperature field, grinding force, and equivalent stress and strain were evaluated by analytical and simulation methods. The results show that the formation of the grinding chips under UVADG is much shorter and straighter than CDG mode at all respective downfeed. The validation experiment compared the simulated and experimental grinding force in both grinding modes to verify the reliability of the FEM results. The validation results demonstrate that the FEM model can accurately describe the single grit UVADG and CDG grinding. At each downfeed, the CDG mode has generated a larger equivalent plastic strain than the UVADG mode, resulting in a higher thermomechanical load on the workpiece. According to the findings, UVADG mode has the least plastic damage on the ground surface, which may improve the surface integrity of the ground component.
- 22 June 2022
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 144 (11) , 1-32
Modeling and Simulation Study of Dry Ultrasonic Vibration-Assisted Grinding of Tool Steel With Single Alumina Abrasive Grit
In the precision fabrication industries, ultrasonic vibration-assisted grinding is widely utilized for the finishing of “difficult-to-cut” materials due to its intermittent cutting mechanism and brittle-to-ductile mode machining. In this study, a two-dimensional finite element model (FEM) of single grit ultrasonic vibration-assisted dry grinding (UVADG) and conventional dry grinding (CDG) of AISI D2 steel has been developed, which taken into account the influence of longitudinal ultrasonic vibration on the workpiece with variable downfeed. The effects of ultrasonic vibration and downfeed on the chip formation mechanism, temperature field, grinding force, and equivalent stress and strain were evaluated by analytical and simulation methods. The results show that the formation of the grinding chips under UVADG is much shorter and straighter than CDG mode at all respective downfeed. The validation experiment compared the simulated and experimental grinding force in both grinding modes to verify the reliability of the FEM results. The validation results demonstrate that the FEM model can accurately describe the single grit UVADG and CDG grinding. At each downfeed, the CDG mode has generated a larger equivalent plastic strain than the UVADG mode, resulting in a higher thermomechanical load on the workpiece. According to the findings, UVADG mode has the least plastic damage on the ground surface, which may improve the surface integrity of the ground component.
- 1 May 2022
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 58 (5) , 369-380
Assessment the Surface Characteristics of Heat-Treated AISI 1040 Steel Using Magnetic Nondestructive Techniques
In the manufacturing industries, heat treatment is extremely important process to achieve desirable thermo-mechanical properties of engineering materials by controlling the specific austenitizing temperature range. These desirable properties were evaluated with several conventional techniques. However, these techniques are more time-consuming, costly, and destructive in nature. To overcome the above serious inspection issues, magnetic nondestructive techniques such as Barkhausen noise (BN) and hysteresis loop (HL) were adopted for surface characterization of different heat-treated AISI 1040 steel at various austenitizing temperatures, i.e., 800, 850, and 900°C. Surface properties were evaluated in terms of microstructure, grain size, and microhardness. BN and HL responses of the heat-treated samples were reported in terms of root mean square (RMS), coercivity, HL, and BN envelope. The experimental results indicated that the drastic variation in the microstructure and microhardness of primary surface and subsurface was observed under quenching at austenitizing temperature 900°C due to rapid cooling of lath martensite, which restricts the formation of perlite. According to nondestructive evaluation, higher BN-RMS and lower coercivity were obtained in annealed samples. A linear correlation between magnetic response variables (BN-RMS and coercivity) and material properties (microhardness and grain size) was obtained at different magnetizing frequencies. Small HL and BN envelopes were found in the quenched sample because of restricted magnetic domains alignment with magnetic field under a fine lath martensite structure.
- 1 May 2022
- Published by Pleiades Publishing Ltd in Russian Journal of Nondestructive Testing
- Vol. 58 (5) , 369-380
Assessment the Surface Characteristics of Heat-Treated AISI 1040 Steel Using Magnetic Nondestructive Techniques
In the manufacturing industries, heat treatment is extremely important process to achieve desirable thermo-mechanical properties of engineering materials by controlling the specific austenitizing temperature range. These desirable properties were evaluated with several conventional techniques. However, these techniques are more time-consuming, costly, and destructive in nature. To overcome the above serious inspection issues, magnetic nondestructive techniques such as Barkhausen noise (BN) and hysteresis loop (HL) were adopted for surface characterization of different heat-treated AISI 1040 steel at various austenitizing temperatures, i.e., 800, 850, and 900°C. Surface properties were evaluated in terms of microstructure, grain size, and microhardness. BN and HL responses of the heat-treated samples were reported in terms of root mean square (RMS), coercivity, HL, and BN envelope. The experimental results indicated that the drastic variation in the microstructure and microhardness of primary surface and subsurface was observed under quenching at austenitizing temperature 900°C due to rapid cooling of lath martensite, which restricts the formation of perlite. According to nondestructive evaluation, higher BN-RMS and lower coercivity were obtained in annealed samples. A linear correlation between magnetic response variables (BN-RMS and coercivity) and material properties (microhardness and grain size) was obtained at different magnetizing frequencies. Small HL and BN envelopes were found in the quenched sample because of restricted magnetic domains alignment with magnetic field under a fine lath martensite structure.
- 26 November 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (4) , 1-12
Effect of ultrasonic vibration assisted dry grinding on hysteresis loop characteristics of AISI D2 tool steel
- 26 November 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (4) , 1-12
Effect of ultrasonic vibration assisted dry grinding on hysteresis loop characteristics of AISI D2 tool steel
- 1 August 2020
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 56, 75-86
Multi-objective optimization of MQL mist parameters for eco-friendly grinding
- 1 August 2020
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 56, 75-86
Multi-objective optimization of MQL mist parameters for eco-friendly grinding
- 1 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (11) , 1165c9
Surface integrity characterization of austenitic, martensitic and ferritic stainless steel under different grinding process
- 1 September 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (11) , 1165c9
Surface integrity characterization of austenitic, martensitic and ferritic stainless steel under different grinding process
- 24 October 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (2) , 026508
Surface integrity characterization of ground hardened H13 hot die steel using different lubrication environments
Surface integrity has a significant effect on the service life of manufactured component as poor surface integrity may cause failure of produced component during its service life. Grinding is the last processing operation during manufacturing cycle of components, which decides the surface integrity of manufactured component. Surface quality of a component depends on the lubricating and cooling performance of cutting fluids during grinding. Thus the present research work investigates the effect of different lubrication modes like dry, flood, minimum quantity lubrication (MQL) on the surface properties of ground hardened H13 hot die steel. Surface integrity was evaluated in terms of surface roughness and microhardness of ground surface, ground surface topography, and microchip morphology. Where as, grinding performance was evalulated in terms of grinding force. The surface topography and elemental composition of ground surface along with microchip were observed using scanning electron microscope (SEM), atomic force microscope (AFM), and energy dispersive X-ray spectroscopy (EDX). Experimental results indicated that MQL with castor oil (CO) provided lowest surface roughness and grinding forces among all lubrication conditions, which were Rɑ-0.245 μm, Rz-1.846 μm, Ft-30.65 N, Fn-42.35 N, respectively. According to AFM analysis, poor surface quality (deep grooves and furrows) was observed under dry grinding due to micro-fractured abrasive grains and hard microchip rubbed over the ground surface. Continuous and smooth (no wear track) microchip was observed with MQL-CO lubrication. Further, EDX analysis indicated that microchips obtained upon MQL-CO lubrication were having very less carbon peaks without any surface oxidation. Higher microhardness was observed with MQL-DIW cooling due to suddenly quenching effect over the nascent ground surface.
- 24 October 2018
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (2) , 026508
Surface integrity characterization of ground hardened H13 hot die steel using different lubrication environments
Surface integrity has a significant effect on the service life of manufactured component as poor surface integrity may cause failure of produced component during its service life. Grinding is the last processing operation during manufacturing cycle of components, which decides the surface integrity of manufactured component. Surface quality of a component depends on the lubricating and cooling performance of cutting fluids during grinding. Thus the present research work investigates the effect of different lubrication modes like dry, flood, minimum quantity lubrication (MQL) on the surface properties of ground hardened H13 hot die steel. Surface integrity was evaluated in terms of surface roughness and microhardness of ground surface, ground surface topography, and microchip morphology. Where as, grinding performance was evalulated in terms of grinding force. The surface topography and elemental composition of ground surface along with microchip were observed using scanning electron microscope (SEM), atomic force microscope (AFM), and energy dispersive X-ray spectroscopy (EDX). Experimental results indicated that MQL with castor oil (CO) provided lowest surface roughness and grinding forces among all lubrication conditions, which were Rɑ-0.245 μm, Rz-1.846 μm, Ft-30.65 N, Fn-42.35 N, respectively. According to AFM analysis, poor surface quality (deep grooves and furrows) was observed under dry grinding due to micro-fractured abrasive grains and hard microchip rubbed over the ground surface. Continuous and smooth (no wear track) microchip was observed with MQL-CO lubrication. Further, EDX analysis indicated that microchips obtained upon MQL-CO lubrication were having very less carbon peaks without any surface oxidation. Higher microhardness was observed with MQL-DIW cooling due to suddenly quenching effect over the nascent ground surface.