Audrey Mandroyan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Audrey Mandroyan has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Chloé Rotty
Institut UTINAM, UMR CNRS 6213, Université de Bourgogne Franche-Comté, 30 avenue de l’Observatoire, 25 009 Besançon, France
2 shared publications- Jean-Yves Hihn
Université Marie et Louis Pasteur, CNRS, Institut UTINAM UMR 6213 F-25000 Besançon, France
2 shared publications - Marie-Laure Doche
UTINAM UMR 6213 CNRS University Bourgogne Franche-Comté
2 shared publications - Agathe Vaché
CEA-LITEN, DTNM, 38000 Grenoble, France
1 shared publication - Emmanuel Billy
CEA-LITEN, DTNM, 38000 Grenoble, France
1 shared publication Ghislain Montavon
1 shared publication
Latest Publications
- Open Access
- 14 April 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (7) , 072508
Selective Electrorefining of Silver from Eutectic Mixtures Containing Silver and Copper at Solar-Panel Waste Ratio
Recycling of photovoltaic (PV) cells is a challenge for recovery of silver and copper, located in the core layer of panels. However, recovery of pure silver continues to be difficult due to parasitic reactions involving co-deposition of copper and silver. This work investigates the electrochemical behavior of Choline-chloride based eutectic mixtures (Ethaline, Propeline, Oxaline, and Reline) in order to achieve selective silver recovery in reproducible conditions. This is possible due to a stable hydration level of 5% achieved at 50 °C, where the physico-chemical and electrochemical properties were found to be stable. The nature of silver or copper complexes in eutectic mixtures was then studied to understand the electrochemical behavior of metal complexes. High-purity silver electrodeposits were obtained in two different Ag: Cu ratios of 1: 1 and 1:17, respectively, the latter mimicking the ratio obtained in PV waste leaching solutions. High silver recovery rate were obtained independently on the eutectic mixture. In the lower Ag: Cu ratio (1:17), purity of the silver deposit depends on the nature of the copper complexes and on electrolyte viscosity. In Reline, a copper-free silver deposit was obtained with a high recovery rate reaching 94.6%.
- 14 April 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (7) , 072508
Open AccessSelective Electrorefining of Silver from Eutectic Mixtures Containing Silver and Copper at Solar-Panel Waste Ratio
Recycling of photovoltaic (PV) cells is a challenge for recovery of silver and copper, located in the core layer of panels. However, recovery of pure silver continues to be difficult due to parasitic reactions involving co-deposition of copper and silver. This work investigates the electrochemical behavior of Choline-chloride based eutectic mixtures (Ethaline, Propeline, Oxaline, and Reline) in order to achieve selective silver recovery in reproducible conditions. This is possible due to a stable hydration level of 5% achieved at 50 °C, where the physico-chemical and electrochemical properties were found to be stable. The nature of silver or copper complexes in eutectic mixtures was then studied to understand the electrochemical behavior of metal complexes. High-purity silver electrodeposits were obtained in two different Ag: Cu ratios of 1: 1 and 1:17, respectively, the latter mimicking the ratio obtained in PV waste leaching solutions. High silver recovery rate were obtained independently on the eutectic mixture. In the lower Ag: Cu ratio (1:17), purity of the silver deposit depends on the nature of the copper complexes and on electrolyte viscosity. In Reline, a copper-free silver deposit was obtained with a high recovery rate reaching 94.6%.
- 1 July 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (7) , 071504
Mechanistic Study of Cast and 3D-Printed Stainless Steel Electropolishing in Acid Media and Deep Eutectic Solvents
The mechanistic analysis of the electropolishing procedure of stainless steel (SS) was revisited using electrochemical impedance spectroscopy. Firstly, the control of the dissolution reaction by diffusion was confirmed with the linear dependence of the limiting current density as a function of the electrode rotation rate using the Levich’s law. Nevertheless, varying the viscosity (by changing temperature from 35 °C–70 °C) show a direct relationship between the diffusion coefficient and the kinematic viscosity, irrespective of the cation concentration at the interface, thus suggesting a minor role in the diffusion limiting step. This limitation is therefore provided by the diffusion of an acceptor specie from the electrolyte toward the anode surface. To discriminate the role of water or mineral anion in the so-called acceptor model, a full descriptive model of the electrochemical behavior of interface was devised for analyzing electropolishing results obtained by electrochemical impedance spectroscopy (EIS) for both cast and additive layer manufactoring (ALM) 316L SS in aqueous acid electrolyte and in deep eutectic solvent (DES). It was shown that the model involving an acceptor specie allows to describe with a good accuracy the electrochemical behavior of the different systems at several potentials.
- 1 July 2022
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 169 (7) , 071504
Mechanistic Study of Cast and 3D-Printed Stainless Steel Electropolishing in Acid Media and Deep Eutectic Solvents
The mechanistic analysis of the electropolishing procedure of stainless steel (SS) was revisited using electrochemical impedance spectroscopy. Firstly, the control of the dissolution reaction by diffusion was confirmed with the linear dependence of the limiting current density as a function of the electrode rotation rate using the Levich’s law. Nevertheless, varying the viscosity (by changing temperature from 35 °C–70 °C) show a direct relationship between the diffusion coefficient and the kinematic viscosity, irrespective of the cation concentration at the interface, thus suggesting a minor role in the diffusion limiting step. This limitation is therefore provided by the diffusion of an acceptor specie from the electrolyte toward the anode surface. To discriminate the role of water or mineral anion in the so-called acceptor model, a full descriptive model of the electrochemical behavior of interface was devised for analyzing electropolishing results obtained by electrochemical impedance spectroscopy (EIS) for both cast and additive layer manufactoring (ALM) 316L SS in aqueous acid electrolyte and in deep eutectic solvent (DES). It was shown that the model involving an acceptor specie allows to describe with a good accuracy the electrochemical behavior of the different systems at several potentials.
- 1 March 2017
- Published by Elsevier in Surfaces and Interfaces
- Vol. 6, 170-176
Comparison of electropolishing behaviours of TSC, ALM and cast 316L stainless steel in H3PO4/H2SO4
- 1 March 2017
- Published by Elsevier in Surfaces and Interfaces
- Vol. 6, 170-176
Comparison of electropolishing behaviours of TSC, ALM and cast 316L stainless steel in H3PO4/H2SO4