Can Ozgur Colpan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Can Ozgur Colpan has a total of 99 co-authors. Here are the top co-authors by number of shared publications:
- Yılser Devrim
Engineering Faculty, Energy System Engineering Department Atılım University Ankara Türkiye
7 shared publications - Anil Erdogan
Energy Institute, Renewable Energy Division, Istanbul Technical University, Ayazağa Campus
6 shared publications David Ouellette
6 shared publications- Mustafa Umut Karaoğlan
Dokuz Eylul University
6 shared publications Adnan Ozden
5 shared publications- Mustafa Ercelik5 shared publications
Latest Publications
- 13 August 2026
- Published by Wiley in Fuel Cells
- Vol. 26 (4)
A Review of Fuel Cell Vehicles for Road Transport: Performance, Economic, and Environmental Evaluations
Road transport is a vital component of daily life and logistics, relying on vehicles such as trucks, buses, and motorcycles. However, its rapid growth has increased carbon emissions, posing serious environmental challenges. To address this, hydrogen has emerged as a key energy carrier for enabling green transportation. Fuel cells, utilizing hydrogen's energy potential, offer an efficient solution for sustainable mobility. This paper presents a comprehensive review of fuel cell vehicles (FCVs) and their role in achieving eco‐friendly transport. Studies of FCVs from 1998 to 2024 are classified by duty type and haul type. This classification encompasses key aspects such as modeling, simulation, software used, and metaheuristic algorithms, which contribute to optimizing system performance and efficiency. Cost and environmental impact assessments are also considered in the classification process. The findings reveal that most studies focus on fuel cell‐powered heavy‐duty trucks. MATLAB/Simulink is the most widely used software for conducting effective modeling and simulation of FCVs. Among the optimization methods reviewed, particle swarm optimization, genetic algorithms, modified student psychology optimization, and teaching–learning‐based optimization provide satisfactory results. Life‐cycle analysis is a critical factor in assessing the carbon emissions of FCVs. It is shown that using fuel cells could cause a reduction in life‐cycle emissions up to 0.2–0.4 tonnes CO 2 ‐eq per vehicle. This study contributes to the application of FCVs with low cost, high efficiency, and minimum ecological impact.
- 13 August 2026
- Published by Wiley in Fuel Cells
- Vol. 26 (4)
A Review of Fuel Cell Vehicles for Road Transport: Performance, Economic, and Environmental Evaluations
Road transport is a vital component of daily life and logistics, relying on vehicles such as trucks, buses, and motorcycles. However, its rapid growth has increased carbon emissions, posing serious environmental challenges. To address this, hydrogen has emerged as a key energy carrier for enabling green transportation. Fuel cells, utilizing hydrogen's energy potential, offer an efficient solution for sustainable mobility. This paper presents a comprehensive review of fuel cell vehicles (FCVs) and their role in achieving eco‐friendly transport. Studies of FCVs from 1998 to 2024 are classified by duty type and haul type. This classification encompasses key aspects such as modeling, simulation, software used, and metaheuristic algorithms, which contribute to optimizing system performance and efficiency. Cost and environmental impact assessments are also considered in the classification process. The findings reveal that most studies focus on fuel cell‐powered heavy‐duty trucks. MATLAB/Simulink is the most widely used software for conducting effective modeling and simulation of FCVs. Among the optimization methods reviewed, particle swarm optimization, genetic algorithms, modified student psychology optimization, and teaching–learning‐based optimization provide satisfactory results. Life‐cycle analysis is a critical factor in assessing the carbon emissions of FCVs. It is shown that using fuel cells could cause a reduction in life‐cycle emissions up to 0.2–0.4 tonnes CO 2 ‐eq per vehicle. This study contributes to the application of FCVs with low cost, high efficiency, and minimum ecological impact.
- Open Access
- 19 June 2026
- Published by Elsevier in SSRN Electronic Journal
MULTI-RESPONSE OPTIMIZATION OF IMMERSION-TYPE BATTERY THERMAL MANAGEMENT SYSTEM
An effective thermal management system is crucial for maintaining the performance and safety of lithium-ion (Li-ion) batteries. In this context, immersion-type battery thermal management systems (BTMS) have gained considerable attention in recent years owing to their high heat transfer capability and electrical insulation characteristics. To systematically evaluate the immersion-type BTMS, initial 3D numerical parametric studies were performed via ANSYS Fluent. Building upon these primary analyses, Response Surface Methodology (RSM) was utilized to determine the effects of battery cell spacing (h), coolant mass flow rate ((m)) ̇ , and battery–container spacing (w) on the overall system performance. The selected response variables included the maximum temperature (T_max), temperature difference (ΔT), pressure drop (ΔP), and energy density (e_d). The developed second-order regression models exhibited high predictive accuracy, and multi-response optimization was performed under the constraints of T_max≤313.15 K and ΔT≤5 K. The optimal parameter combination was identified as h=12.919 mm, m ̇=0.171 kg/s, and w=33.485 mm, yielding T_max=304.853 K, ΔT=4.310 K, ΔP=193.810 Pa, and e_d=63.191 Wh/kg. These findings demonstrate that a balanced interplay between geometric parameters and flow conditions can simultaneously ensure effective heat removal and acceptable energy density. The results provide valuable engineering insights for optimizing immersion-type BTMS designs intended for high-performance battery modules.
- 19 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMULTI-RESPONSE OPTIMIZATION OF IMMERSION-TYPE BATTERY THERMAL MANAGEMENT SYSTEM
An effective thermal management system is crucial for maintaining the performance and safety of lithium-ion (Li-ion) batteries. In this context, immersion-type battery thermal management systems (BTMS) have gained considerable attention in recent years owing to their high heat transfer capability and electrical insulation characteristics. To systematically evaluate the immersion-type BTMS, initial 3D numerical parametric studies were performed via ANSYS Fluent. Building upon these primary analyses, Response Surface Methodology (RSM) was utilized to determine the effects of battery cell spacing (h), coolant mass flow rate ((m)) ̇ , and battery–container spacing (w) on the overall system performance. The selected response variables included the maximum temperature (T_max), temperature difference (ΔT), pressure drop (ΔP), and energy density (e_d). The developed second-order regression models exhibited high predictive accuracy, and multi-response optimization was performed under the constraints of T_max≤313.15 K and ΔT≤5 K. The optimal parameter combination was identified as h=12.919 mm, m ̇=0.171 kg/s, and w=33.485 mm, yielding T_max=304.853 K, ΔT=4.310 K, ΔP=193.810 Pa, and e_d=63.191 Wh/kg. These findings demonstrate that a balanced interplay between geometric parameters and flow conditions can simultaneously ensure effective heat removal and acceptable energy density. The results provide valuable engineering insights for optimizing immersion-type BTMS designs intended for high-performance battery modules.
- 15 March 2026
- Published by Wiley in Fuel Cells
- Vol. 26 (2)
Performance Analysis of a Small‐Sized Hybrid Vehicle on a Real‐World Inclined Route Under WLTP, ARTEMIS, and NEDC Drive Cycles
The decarbonization of the transportation sector is imperative for achieving targeted reductions in greenhouse gas emissions, necessitating the integration of renewable energy pathways. While battery electric vehicles (BEVs) are widely promoted as an environmentally sustainable solution, their utility is often constrained by the significant battery mass and corresponding weight penalty required to achieve extended operational ranges. This fundamental limitation has motivated the rigorous development of fuel cell hybrid electric vehicles (FCHEVs) as a viable technological alternative. In recent years, simulation of powertrain systems has emerged as a prevalent methodology for assessing vehicle performance and energy efficiency across various electric, hybrid, and FCHEV architectures. However, a significant portion of the existing literature on hybrid vehicles focuses on component‐level optimization or specific hybrid topologies, often relying on simulations that assume idealized, flat‐terrain road profiles, thereby neglecting the impact of topographical gradients. This study addresses this research gap by developing a comprehensive powertrain system model for a battery/fuel cell hybrid vehicle implemented in MATLAB/Simulink. The model's performance is dynamically evaluated under the WLTP, ARTEMIS, and NEDC driving cycles, which are distinctly applied to the GraphHooper Maps‐derived real‐world inclined route in Elazığ. The simulations yield critical performance indicators, including the power distribution dynamics among powertrain components, changes in battery state of charge (SoC), and vehicle speed control. Furthermore, an adaptive PID controller is implemented to ensure that the vehicle's instantaneous speed precisely tracks the reference speed trajectory. This work aims to provide a high‐fidelity simulation approach that more accurately reflects real‐world driving conditions, facilitating a robust evaluation of hybrid vehicle performance in realistic operational scenarios. In this context, for the WLTP, ARTEMIS, and NEDC driving cycles applied to a 3.1‐km real‐world route, the battery SoC was improved by 1.5%, 1.8%, and 1.6%, respectively, in the hybrid configuration. Moreover, owing to the proposed adaptive control strategy, the vehicle speed tracked the reference profile with an average accuracy of 99.8%.
- 15 March 2026
- Published by Wiley in Fuel Cells
- Vol. 26 (2)
Performance Analysis of a Small‐Sized Hybrid Vehicle on a Real‐World Inclined Route Under WLTP, ARTEMIS, and NEDC Drive Cycles
The decarbonization of the transportation sector is imperative for achieving targeted reductions in greenhouse gas emissions, necessitating the integration of renewable energy pathways. While battery electric vehicles (BEVs) are widely promoted as an environmentally sustainable solution, their utility is often constrained by the significant battery mass and corresponding weight penalty required to achieve extended operational ranges. This fundamental limitation has motivated the rigorous development of fuel cell hybrid electric vehicles (FCHEVs) as a viable technological alternative. In recent years, simulation of powertrain systems has emerged as a prevalent methodology for assessing vehicle performance and energy efficiency across various electric, hybrid, and FCHEV architectures. However, a significant portion of the existing literature on hybrid vehicles focuses on component‐level optimization or specific hybrid topologies, often relying on simulations that assume idealized, flat‐terrain road profiles, thereby neglecting the impact of topographical gradients. This study addresses this research gap by developing a comprehensive powertrain system model for a battery/fuel cell hybrid vehicle implemented in MATLAB/Simulink. The model's performance is dynamically evaluated under the WLTP, ARTEMIS, and NEDC driving cycles, which are distinctly applied to the GraphHooper Maps‐derived real‐world inclined route in Elazığ. The simulations yield critical performance indicators, including the power distribution dynamics among powertrain components, changes in battery state of charge (SoC), and vehicle speed control. Furthermore, an adaptive PID controller is implemented to ensure that the vehicle's instantaneous speed precisely tracks the reference speed trajectory. This work aims to provide a high‐fidelity simulation approach that more accurately reflects real‐world driving conditions, facilitating a robust evaluation of hybrid vehicle performance in realistic operational scenarios. In this context, for the WLTP, ARTEMIS, and NEDC driving cycles applied to a 3.1‐km real‐world route, the battery SoC was improved by 1.5%, 1.8%, and 1.6%, respectively, in the hybrid configuration. Moreover, owing to the proposed adaptive control strategy, the vehicle speed tracked the reference profile with an average accuracy of 99.8%.
- Open Access
- 10 September 2025
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 226
A review on membranes for anion exchange membrane water electrolyzers
- 10 September 2025
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 226
Open AccessA review on membranes for anion exchange membrane water electrolyzers
- 8 February 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 143, 1295-1306
Performance assessment of anion exchange electrolyzer with PBI-BASED membrane through 0-D modeling
- 8 February 2025
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 143, 1295-1306
Performance assessment of anion exchange electrolyzer with PBI-BASED membrane through 0-D modeling
- 20 November 2024
- Published by Springer Nature
- p. 107-112
Progress on PEM Fuel Cell–Powered Unmanned Aerial Vehicle Research
- 20 November 2024
- Published by Springer Nature
- p. 107-112
Progress on PEM Fuel Cell–Powered Unmanned Aerial Vehicle Research
- 17 May 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 75, 662-689
Dynamic analysis and multi-objective optimization of solar and hydrogen energy-based systems for residential applications: A review
- 17 May 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 75, 662-689
Dynamic analysis and multi-objective optimization of solar and hydrogen energy-based systems for residential applications: A review
- 14 December 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 67, 1181-1193
Design, modeling, and analysis of a PV/T and PEM fuel cell based hybrid energy system for an off-grid house
- 14 December 2023
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 67, 1181-1193
Design, modeling, and analysis of a PV/T and PEM fuel cell based hybrid energy system for an off-grid house