Prasenjit Mondal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Prasenjit Mondal has a total of 81 co-authors. Here are the top co-authors by number of shared publications:
- Amit Kumar Chaurasia
Indian Institute of Technology
7 shared publications - Pushpraj Patel
Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667, India
6 shared publications - Shubhi Gupta
Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667, India
6 shared publications Anil Kumar Varma
Department of Chemical Engineering, Assam Energy Institute (A centre of RGIPT, Jais, Amethi), Sivasagar, India
5 shared publications- Hemant Goyal
Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee, Uttarakhand 247667, India
5 shared publications Sanjeevani Hooda
Department of Chemical Engineering, Indian Institute of Technology Roorkee, Roorkee, India
4 shared publications
Latest Publications
- 19 October 2026
- Published by Wiley in The Canadian Journal of Chemical Engineering
Spent cathode powder catalyzed co‐pyrolysis of P rosopis juliflora (Vilayati Babul) pods and waste LDPE for bio‐fuel production: Comprehensive thermogravimetric and kinetic study with ANN ‐based prediction and product characterization
The global community is increasingly concerned about the disposal of spent lithium‐ion batteries, as their improper disposal poses serious environmental hazards. Moreover, large amounts of waste plastic and biomass are generated every year, which again creates serious threat to the environment. To address these issues, proposed research focuses on examining the co‐pyrolysis of an invasive lignocellulosic biomass, Prosopis juliflora pods (PJ) with low‐density polyethylene (LDPE) using spent cathode powder (SCP) derived from waste lithium‐ion batteries as a catalyst. Thermogravimetric analysis was conducted at three different heating rates of 10, 20, and 30°C/min for the PJ and LDPE blend (1:1 wt.%), and SCP catalyst to feedstock (PJ & LDPE) blend (1:2 wt.%). Further, kinetic and thermodynamic investigations were conducted through the thermogravimetric analysis (TGA) data, using the Kissinger–Akahira–Sunose (KAS), Ozawa–Flynn–Wall (OFW), and Starink methods. The catalytic effect of SCP greatly reduced the required activation energy, and the values for PJ + LDPE_SCP feedstock were 134.00, 129.09, and 129.47 kJ/mol using OFW, KAS, and Starink methods. For the catalytic process, Δ H ranged from 17.60 to 111.48 kJ/mol as the conversion level changed from 0.1 to 0.9. The average Δ G was 208.37 kJ/mol, and the average Δ S was −0.1126 kJ/mol/K. GC–MS and FTIR analysis revealed a marked reduction in oxygenated compounds in the bio‐oil from catalytic runs compared to non‐catalytic. The artificial neural network (ANN) model demonstrated high reliability with regression coefficient close to 0.99. The findings achieve the goal of efficiently dealing with the problem of plastic and electronic waste while producing value added fuels.
- 19 October 2026
- Published by Wiley in The Canadian Journal of Chemical Engineering
Spent cathode powder catalyzed co‐pyrolysis of P rosopis juliflora (Vilayati Babul) pods and waste LDPE for bio‐fuel production: Comprehensive thermogravimetric and kinetic study with ANN ‐based prediction and product characterization
The global community is increasingly concerned about the disposal of spent lithium‐ion batteries, as their improper disposal poses serious environmental hazards. Moreover, large amounts of waste plastic and biomass are generated every year, which again creates serious threat to the environment. To address these issues, proposed research focuses on examining the co‐pyrolysis of an invasive lignocellulosic biomass, Prosopis juliflora pods (PJ) with low‐density polyethylene (LDPE) using spent cathode powder (SCP) derived from waste lithium‐ion batteries as a catalyst. Thermogravimetric analysis was conducted at three different heating rates of 10, 20, and 30°C/min for the PJ and LDPE blend (1:1 wt.%), and SCP catalyst to feedstock (PJ & LDPE) blend (1:2 wt.%). Further, kinetic and thermodynamic investigations were conducted through the thermogravimetric analysis (TGA) data, using the Kissinger–Akahira–Sunose (KAS), Ozawa–Flynn–Wall (OFW), and Starink methods. The catalytic effect of SCP greatly reduced the required activation energy, and the values for PJ + LDPE_SCP feedstock were 134.00, 129.09, and 129.47 kJ/mol using OFW, KAS, and Starink methods. For the catalytic process, Δ H ranged from 17.60 to 111.48 kJ/mol as the conversion level changed from 0.1 to 0.9. The average Δ G was 208.37 kJ/mol, and the average Δ S was −0.1126 kJ/mol/K. GC–MS and FTIR analysis revealed a marked reduction in oxygenated compounds in the bio‐oil from catalytic runs compared to non‐catalytic. The artificial neural network (ANN) model demonstrated high reliability with regression coefficient close to 0.99. The findings achieve the goal of efficiently dealing with the problem of plastic and electronic waste while producing value added fuels.
- 20 August 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
Spent Red Mud-Catalyzed Copyrolysis of Waste Pods of Prosopis juliflora and Low-Density Polyethylene Waste: Thermal and Kinetic Insights and Predictive Modeling Using Artificial Neural Network Approach
In the present study, catalytic copyrolysis of Prosopis juliflora pods (PJ) with waste low-density polyethylene (LDPE) was investigated using a spent red mud-derived catalyst (RMC) through thermogravimetric analysis. The analysis was conducted at three heating rates of 10, 20, and 30 °C/min for the PJ and LDPE blend (1:1), and the blend of feedstock (PJ & LDPE) with RMC catalyst (1:1). Further, kinetic and thermodynamic analyses were conducted, and the reaction mechanism was elucidated through Criado’s Z-master plot method. Kinetic parameters were assessed using four different iso-conversional models, and subsequently thermodynamic parameters were estimated. The results from the present study showed that the average activation energy was reduced by 9–10% in all models with the incorporation of spent red mud-derived catalyst (RMC) in copyrolysis. Furthermore, an artificial neural network (ANN) model was applied to predict the catalytic copyrolysis behavior of PJ and LDPE waste. A high regression coefficient (R ≈ 0.99) and a low mean squared error (MSE ≈ 10–5) were observed, which suggests the accuracy of the prediction model for copyrolytic degradation of PJ and LDPE waste. Hence, the study confirms the potential for copyrolytic conversion of PJ and LDPE waste using a spent red mud-derived catalyst into fuels and chemicals via a cost-effective and sustainable process.
- 20 August 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
Spent Red Mud-Catalyzed Copyrolysis of Waste Pods of Prosopis juliflora and Low-Density Polyethylene Waste: Thermal and Kinetic Insights and Predictive Modeling Using Artificial Neural Network Approach
In the present study, catalytic copyrolysis of Prosopis juliflora pods (PJ) with waste low-density polyethylene (LDPE) was investigated using a spent red mud-derived catalyst (RMC) through thermogravimetric analysis. The analysis was conducted at three heating rates of 10, 20, and 30 °C/min for the PJ and LDPE blend (1:1), and the blend of feedstock (PJ & LDPE) with RMC catalyst (1:1). Further, kinetic and thermodynamic analyses were conducted, and the reaction mechanism was elucidated through Criado’s Z-master plot method. Kinetic parameters were assessed using four different iso-conversional models, and subsequently thermodynamic parameters were estimated. The results from the present study showed that the average activation energy was reduced by 9–10% in all models with the incorporation of spent red mud-derived catalyst (RMC) in copyrolysis. Furthermore, an artificial neural network (ANN) model was applied to predict the catalytic copyrolysis behavior of PJ and LDPE waste. A high regression coefficient (R ≈ 0.99) and a low mean squared error (MSE ≈ 10–5) were observed, which suggests the accuracy of the prediction model for copyrolytic degradation of PJ and LDPE waste. Hence, the study confirms the potential for copyrolytic conversion of PJ and LDPE waste using a spent red mud-derived catalyst into fuels and chemicals via a cost-effective and sustainable process.
- 3 August 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (31) , 16698-16717
Synergistic Production of Fuel-Grade Bio-Oil and Carbon Rich Biochar from Co-Pyrolysis of Spent Coffee Grounds and HDPE: Process Optimization Using Response Surface Methodology and Machine Learning
This study investigates the modeling and optimization of copyrolysis of Spent Coffee Grounds and HDPE for sustainable biofuel production, emphasizing the influence of key process parameters, including heating rate, temperature and inert flow rate. A framework coupling Response Surface Methodology (RSM) and XGBoost algorithm achieved high predictive accuracy with minimal error. Interpretation via explainable artificial intelligence (XAI) identified temperature as the most influential parameter, followed by heating rate. At optimized conditions (A heating rate of 48.12 °C/min, temperature of 544.45 °C and inert flow rate of 183.59 mL/min.), the actual yield of bio-oil was 53.11 wt %, consistent with RSM (52.12 wt %) and XGBoost (53.04 wt %) predictions, reflecting absolute errors within 0–1 wt %. GC–MS analysis confirmed that the bio-oil contained hydrocarbons exceeding 80%. Comprehensive physicochemical analysis of the noncondensable gases (NCGs) and solid residue confirms their viability as energy vectors and highlights their prospective utilization in various industrial and environmental applications. This study demonstrates the efficacy of the copyrolysis process for the production of biofuels from SCG and HDPE. Further research is necessary to optimize process parameters, conduct a comprehensive life-cycle assessment, and evaluate the techno-economic viability of scaling up the process.
- 3 August 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (31) , 16698-16717
Synergistic Production of Fuel-Grade Bio-Oil and Carbon Rich Biochar from Co-Pyrolysis of Spent Coffee Grounds and HDPE: Process Optimization Using Response Surface Methodology and Machine Learning
This study investigates the modeling and optimization of copyrolysis of Spent Coffee Grounds and HDPE for sustainable biofuel production, emphasizing the influence of key process parameters, including heating rate, temperature and inert flow rate. A framework coupling Response Surface Methodology (RSM) and XGBoost algorithm achieved high predictive accuracy with minimal error. Interpretation via explainable artificial intelligence (XAI) identified temperature as the most influential parameter, followed by heating rate. At optimized conditions (A heating rate of 48.12 °C/min, temperature of 544.45 °C and inert flow rate of 183.59 mL/min.), the actual yield of bio-oil was 53.11 wt %, consistent with RSM (52.12 wt %) and XGBoost (53.04 wt %) predictions, reflecting absolute errors within 0–1 wt %. GC–MS analysis confirmed that the bio-oil contained hydrocarbons exceeding 80%. Comprehensive physicochemical analysis of the noncondensable gases (NCGs) and solid residue confirms their viability as energy vectors and highlights their prospective utilization in various industrial and environmental applications. This study demonstrates the efficacy of the copyrolysis process for the production of biofuels from SCG and HDPE. Further research is necessary to optimize process parameters, conduct a comprehensive life-cycle assessment, and evaluate the techno-economic viability of scaling up the process.
- 9 June 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (12) , 9441-9452
Engineering a PANI/MWCNT/V 2 O 5 Ternary Composite for Hybrid Supercapacitors
- 9 June 2026
- Published by American Chemical Society (ACS) in ACS Applied Polymer Materials
- Vol. 8 (12) , 9441-9452
Engineering a PANI/MWCNT/V 2 O 5 Ternary Composite for Hybrid Supercapacitors
- 25 May 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (22) , 11224-11237
Integrated Optimization and Life Cycle Assessments of Co-Hydrothermal Liquefaction of Microalgae and Spent Coffee Grounds in a Methanol–Water System for Sustainable Production of Biocrude
- 25 May 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (22) , 11224-11237
Integrated Optimization and Life Cycle Assessments of Co-Hydrothermal Liquefaction of Microalgae and Spent Coffee Grounds in a Methanol–Water System for Sustainable Production of Biocrude
- 5 March 2026
- Published by Springer Nature in Mine Water and the Environment
- Vol. 45 (1) , 52-64
Bioremediation of Acid Mine Drainage with Bacillus cereus: A Sustainable Solution for Multi-metal Contamination in Affected Mining Regions
- 5 March 2026
- Published by Springer Nature in Mine Water and the Environment
- Vol. 45 (1) , 52-64
Bioremediation of Acid Mine Drainage with Bacillus cereus: A Sustainable Solution for Multi-metal Contamination in Affected Mining Regions
- 15 January 2026
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 12 (1) , 211-226
Techno-economic and life cycle assessment of an integrated electrocoagulation process for sustainable treatment of arsenic and fluoride contaminated groundwater
The present study evaluated the environmental and economic sustainability of an electrocoagulation-based system for arsenic and fluoride removal through life cycle analysis (LCA) and techno-economic assessment (TEA).
- 15 January 2026
- Published by Royal Society of Chemistry (RSC) in Environmental Science: Water Research & Technology
- Vol. 12 (1) , 211-226
Techno-economic and life cycle assessment of an integrated electrocoagulation process for sustainable treatment of arsenic and fluoride contaminated groundwater
The present study evaluated the environmental and economic sustainability of an electrocoagulation-based system for arsenic and fluoride removal through life cycle analysis (LCA) and techno-economic assessment (TEA).
- 4 December 2025
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 11 (3) , 674-690
Recovery of lithium from spent lithium-ion batteries using carbothermal reduction with spent coffee grounds: a parametric optimization using a combined approach of response surface methodology and machine learning
Spent coffee grounds enabled selective lithium recovery as Li 2 CO 3 from spent LIBs. Process optimization using RSM and machine learning offers a green and sustainable recycling strategy.
- 4 December 2025
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 11 (3) , 674-690
Recovery of lithium from spent lithium-ion batteries using carbothermal reduction with spent coffee grounds: a parametric optimization using a combined approach of response surface methodology and machine learning
Spent coffee grounds enabled selective lithium recovery as Li 2 CO 3 from spent LIBs. Process optimization using RSM and machine learning offers a green and sustainable recycling strategy.
- 26 November 2025
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 237 (3) , 189
Optimization and Modeling of Adsorptive Greywater Treatment System using RSM and ANN
- 26 November 2025
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 237 (3) , 189
Optimization and Modeling of Adsorptive Greywater Treatment System using RSM and ANN
- 30 June 2025
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 23 (7) , 791-801
Thermodynamic equilibrium modeling of gasification for syngas production from carbonaceous feed containing the sulfur impurity
The present study deals with modeling and simulating the gasification process for syngas production. Equilibrium modeling was done to study the product gas composition by changing the process parameters, viz., reaction temperature, equivalence ratio, and moisture content. Coal, wood waste, eucalyptus, pine, and oak were gasification feedstocks. System model equations have been solved using MATLAB software. The model is studied for the range of temperature (800–1400 K), moisture content (7–40 %), and equivalence ratio (0–1). The results of the simulation study were compared with the values in the literature. The results show that the model is entirely satisfactory for the equivalence ratio range of 0.15–0.35. The variation in operating conditions, i.e., equivalence ratio, temperature, moisture content, and the characteristics of carbonaceous feed material, greatly influences the exit gas composition. A carbonaceous feed with almost the same syngas composition can be used for the same gasification process without changing the parameters. Further, coal-derived syngas has different characteristics from the wood waste of oak, pine, and eucalyptus feedstocks. Under optimal conditions, H 2 and CO concentrations reached 38 and 35 %, respectively. Increasing sulfur content by 2 % led to a 6 % reduction in CO yield, confirming its inhibitory effect on gasification efficiency.
- 30 June 2025
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 23 (7) , 791-801
Thermodynamic equilibrium modeling of gasification for syngas production from carbonaceous feed containing the sulfur impurity
The present study deals with modeling and simulating the gasification process for syngas production. Equilibrium modeling was done to study the product gas composition by changing the process parameters, viz., reaction temperature, equivalence ratio, and moisture content. Coal, wood waste, eucalyptus, pine, and oak were gasification feedstocks. System model equations have been solved using MATLAB software. The model is studied for the range of temperature (800–1400 K), moisture content (7–40 %), and equivalence ratio (0–1). The results of the simulation study were compared with the values in the literature. The results show that the model is entirely satisfactory for the equivalence ratio range of 0.15–0.35. The variation in operating conditions, i.e., equivalence ratio, temperature, moisture content, and the characteristics of carbonaceous feed material, greatly influences the exit gas composition. A carbonaceous feed with almost the same syngas composition can be used for the same gasification process without changing the parameters. Further, coal-derived syngas has different characteristics from the wood waste of oak, pine, and eucalyptus feedstocks. Under optimal conditions, H 2 and CO concentrations reached 38 and 35 %, respectively. Increasing sulfur content by 2 % led to a 6 % reduction in CO yield, confirming its inhibitory effect on gasification efficiency.