Rosa Maria Miranda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rosa Maria Miranda has a total of 136 co-authors. Here are the top co-authors by number of shared publications:
- Luisa Quintino
Universidade de Lisboa
38 shared publications - Telmo Gomes Santos
UNIDEMI, Department of Mechanical and Industrial Engineering, NOVA School of Science and Technology, Universidade NOVA de Lisboa, Caparica, Portugal
28 shared publications - Joao Pedro Oliveira
CENIMAT/I3N, Department of Materials Science, NOVA School of Science and Technology, Universidade NOVA de Lisboa, Caparica, Portugal
20 shared publications - Pedro Vilaça
Department of Energy and Mechanical Engineering, School of Engineering, Aalto University, 02150 Espoo, Finland
20 shared publications - Francisco Manuel Braz Fernandes
CENIMAT/I3N, Department of Materials Science, NOVA School of Science and Technology, Universidade NOVA de Lisboa, 2829-516 Caparica, Portugal
18 shared publications - João Fernando Pereira Gomes
Departamento de Engenharia Química, Instituto Superior de Engenharia de Lisboa (ISEL), Instituto Politécnico de Lisboa, R. Conselheiro Emídio Navarro 1, 1959-007 Lisboa, Portugal
11 shared publications
Latest Publications
- Open Access
Multisensor Inspection of Laser-Brazed Joints in the Automotive Industry
Automobile laser brazing remains a complex process whose results are affected by several process variables that may result in nonacceptable welds. A multisensory customized inspection system is proposed, with two distinct non-destructive techniques: the potential drop method and eddy current testing. New probes were designed, simulated, produced, and experimentally validated in automobile’s laser-brazed weld beads with artificially introduced defects. The numerical simulations allowed the development of a new four-point probe configuration in a non-conventional orthogonal shape demonstrating a superior performance in both simulation and experimental validation. The dedicated inspection system allowed the detection of porosities, cracks, and lack of bonding defects, demonstrating the redundancy and complementarity these two techniques provide.
Open AccessMultisensor Inspection of Laser-Brazed Joints in the Automotive Industry
Automobile laser brazing remains a complex process whose results are affected by several process variables that may result in nonacceptable welds. A multisensory customized inspection system is proposed, with two distinct non-destructive techniques: the potential drop method and eddy current testing. New probes were designed, simulated, produced, and experimentally validated in automobile’s laser-brazed weld beads with artificially introduced defects. The numerical simulations allowed the development of a new four-point probe configuration in a non-conventional orthogonal shape demonstrating a superior performance in both simulation and experimental validation. The dedicated inspection system allowed the detection of porosities, cracks, and lack of bonding defects, demonstrating the redundancy and complementarity these two techniques provide.
- Open Access
- 14 September 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (3-4) , 1183-1195
New directions for inline inspection of automobile laser welds using non-destructive testing
An innovative pilot installation and eddy current testing (ECT) inspection system for laser-brazed joints is presented. The proposed system detects both surface and sub-surface welding defects operating autonomously and integrated with a robotized arm. Customized eddy current probes were designed and experimentally validated detecting pore defects with 0.13 mm diameter and sub-surface defects buried 1 mm deep. The integration of the system and the manufacturing process towards an Industry 4.0 quality control paradigm is also discussed.
- 14 September 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (3-4) , 1183-1195
Open AccessNew directions for inline inspection of automobile laser welds using non-destructive testing
An innovative pilot installation and eddy current testing (ECT) inspection system for laser-brazed joints is presented. The proposed system detects both surface and sub-surface welding defects operating autonomously and integrated with a robotized arm. Customized eddy current probes were designed and experimentally validated detecting pore defects with 0.13 mm diameter and sub-surface defects buried 1 mm deep. The integration of the system and the manufacturing process towards an Industry 4.0 quality control paradigm is also discussed.
- Top Cited PapersOpen Access
Current Status and Perspectives on Wire and Arc Additive Manufacturing (WAAM)
Additive manufacturing has revolutionized the manufacturing paradigm in recent years due to the possibility of creating complex shaped three-dimensional parts which can be difficult or impossible to obtain by conventional manufacturing processes. Among the different additive manufacturing techniques, wire and arc additive manufacturing (WAAM) is suitable to produce large metallic parts owing to the high deposition rates achieved, which are significantly larger than powder-bed techniques, for example. The interest in WAAM is steadily increasing, and consequently, significant research efforts are underway. This review paper aims to provide an overview of the most significant achievements in WAAM, highlighting process developments and variants to control the microstructure, mechanical properties, and defect generation in the as-built parts; the most relevant engineering materials used; the main deposition strategies adopted to minimize residual stresses and the effect of post-processing heat treatments to improve the mechanical properties of the parts. An important aspect that still hinders this technology is certification and nondestructive testing of the parts, and this is discussed. Finally, a general perspective of future advancements is presented.
Top Cited PapersOpen AccessCurrent Status and Perspectives on Wire and Arc Additive Manufacturing (WAAM)
Additive manufacturing has revolutionized the manufacturing paradigm in recent years due to the possibility of creating complex shaped three-dimensional parts which can be difficult or impossible to obtain by conventional manufacturing processes. Among the different additive manufacturing techniques, wire and arc additive manufacturing (WAAM) is suitable to produce large metallic parts owing to the high deposition rates achieved, which are significantly larger than powder-bed techniques, for example. The interest in WAAM is steadily increasing, and consequently, significant research efforts are underway. This review paper aims to provide an overview of the most significant achievements in WAAM, highlighting process developments and variants to control the microstructure, mechanical properties, and defect generation in the as-built parts; the most relevant engineering materials used; the main deposition strategies adopted to minimize residual stresses and the effect of post-processing heat treatments to improve the mechanical properties of the parts. An important aspect that still hinders this technology is certification and nondestructive testing of the parts, and this is discussed. Finally, a general perspective of future advancements is presented.
- 23 February 2019
- Published by Taylor & Francis in Inhalation Toxicology
- Vol. 31 (3) , 125-130
Evaluation of the amount of nanoparticles emitted in LASER additive manufacture/welding
Objectives: The objective of this study was the evaluation of the professional exposure to nanoparticles during tasks performed in workstations for production of metallic parts by laser welding additive manufacturing. Materials and methods: The study was developed in an installed additive manufacturing machine, having controlled temperature and humidity in an industrial unit where metal parts were being produced using stainless steel powders of granulometry of 10 to 35 μm. Results and discussion: Monitoring of airborne nanoparticles emission was made using adequate equipment, which showed considerable number of nanoparticles over the baseline, having the same composition as the steel powder used. Conclusion: It is concluded that the values of professional exposure to nanoparticles are high in these workstations and that the nanoparticles to which the workers are exposed are small in size (around 15 nm), thus having a strong capacity for alveolar penetration and, consequently, with a strong possibility of passing to the bloodstream, accumulating in the body.
- 23 February 2019
- Published by Taylor & Francis in Inhalation Toxicology
- Vol. 31 (3) , 125-130
Evaluation of the amount of nanoparticles emitted in LASER additive manufacture/welding
Objectives: The objective of this study was the evaluation of the professional exposure to nanoparticles during tasks performed in workstations for production of metallic parts by laser welding additive manufacturing. Materials and methods: The study was developed in an installed additive manufacturing machine, having controlled temperature and humidity in an industrial unit where metal parts were being produced using stainless steel powders of granulometry of 10 to 35 μm. Results and discussion: Monitoring of airborne nanoparticles emission was made using adequate equipment, which showed considerable number of nanoparticles over the baseline, having the same composition as the steel powder used. Conclusion: It is concluded that the values of professional exposure to nanoparticles are high in these workstations and that the nanoparticles to which the workers are exposed are small in size (around 15 nm), thus having a strong capacity for alveolar penetration and, consequently, with a strong possibility of passing to the bloodstream, accumulating in the body.
- 1 July 2018
- Published by Elsevier in Scripta Materialia
- Vol. 152, 122-126
Effects of laser processing on the transformation characteristics of NiTi: A contribute to additive manufacturing
- 1 July 2018
- Published by Elsevier in Scripta Materialia
- Vol. 152, 122-126
Effects of laser processing on the transformation characteristics of NiTi: A contribute to additive manufacturing
- 1 June 2018
- Published by Elsevier in Materials & Design
- Vol. 148, 145-152
Laser welding of Cu-Al-Be shape memory alloys: Microstructure and mechanical properties
- 1 June 2018
- Published by Elsevier in Materials & Design
- Vol. 148, 145-152
Laser welding of Cu-Al-Be shape memory alloys: Microstructure and mechanical properties
- 1 August 2017
- Published by Elsevier in Materials & Design
- Vol. 128, 166-175
Dissimilar laser welding of superelastic NiTi and CuAlMn shape memory alloys
- 1 August 2017
- Published by Elsevier in Materials & Design
- Vol. 128, 166-175
Dissimilar laser welding of superelastic NiTi and CuAlMn shape memory alloys
- 31 July 2017
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 23 (2) , 172-179
Magnetic pulse welding: machine optimisation for aluminium tubular joints production
Magnetic pulse welding (MPW) has recently been increasingly investigated for specific dissimilar material joining applications since this is a solid state clean process, with good energy efficiency that almost does not produce thermal degradation effects in the joint. This paper presents developments performed on a MPW machine to produce tubular joints in AA6063-T6 with lower energy than commercial machines. The welds were structural and mechanically characterised and fracture was always observed at ultimate tensile strengths above those of the base materials and outside the welded zone. An energy balance is also presented to verify the machine optimisation and the energy used compared to that reported for commercially available machines.
- 31 July 2017
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 23 (2) , 172-179
Magnetic pulse welding: machine optimisation for aluminium tubular joints production
Magnetic pulse welding (MPW) has recently been increasingly investigated for specific dissimilar material joining applications since this is a solid state clean process, with good energy efficiency that almost does not produce thermal degradation effects in the joint. This paper presents developments performed on a MPW machine to produce tubular joints in AA6063-T6 with lower energy than commercial machines. The welds were structural and mechanically characterised and fracture was always observed at ultimate tensile strengths above those of the base materials and outside the welded zone. An energy balance is also presented to verify the machine optimisation and the energy used compared to that reported for commercially available machines.
- Open Access
Using Biotechnology to Solve Engineering Problems: Non-Destructive Testing of Microfabrication Components
In an increasingly miniaturised technological world, non-destructive testing (NDT) methodologies able to detect defects at the micro scale are necessary to prevent failures. Although several existing methods allow the detection of defects at that scale, their application may be hindered by the small size of the samples to examine. In this study, the application of bacterial cells to help the detection of fissures, cracks, and voids on the surface of metals is proposed. The application of magnetic and electric fields after deposition of the cells ensured the distribution of the cells over the entire surfaces and helped the penetration of the cells inside the defects. The use of fluorophores to stain the cells allowed their visualisation and the identification of the defects. Furthermore, the size and zeta potential of the cells and their production of siderophores and biosurfactants could be influenced to detect smaller defects. Micro and nano surface defects made in aluminium, steel, and copper alloys could be readily identified by two Staphylococcus strains and Rhodococcus erythropolis cells.
Open AccessUsing Biotechnology to Solve Engineering Problems: Non-Destructive Testing of Microfabrication Components
In an increasingly miniaturised technological world, non-destructive testing (NDT) methodologies able to detect defects at the micro scale are necessary to prevent failures. Although several existing methods allow the detection of defects at that scale, their application may be hindered by the small size of the samples to examine. In this study, the application of bacterial cells to help the detection of fissures, cracks, and voids on the surface of metals is proposed. The application of magnetic and electric fields after deposition of the cells ensured the distribution of the cells over the entire surfaces and helped the penetration of the cells inside the defects. The use of fluorophores to stain the cells allowed their visualisation and the identification of the defects. Furthermore, the size and zeta potential of the cells and their production of siderophores and biosurfactants could be influenced to detect smaller defects. Micro and nano surface defects made in aluminium, steel, and copper alloys could be readily identified by two Staphylococcus strains and Rhodococcus erythropolis cells.
- Top Cited Papers
- 1 July 2017
- Published by Elsevier in Progress in Materials Science
- Vol. 88, 412-466
Welding and Joining of NiTi Shape Memory Alloys: A Review
- 1 July 2017
- Published by Elsevier in Progress in Materials Science
- Vol. 88, 412-466
Top Cited PapersWelding and Joining of NiTi Shape Memory Alloys: A Review