Fei Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Fei Li has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
Deyan He
2 shared publicationsFalun Song
2 shared publicationsHongwei Yue
2 shared publicationsXiao Jin
2 shared publicationsYanli Qin
2 shared publicationsZhibo Yang
2 shared publications
Latest Publications
- 10 August 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (6)
Influence of pre-existing negative surface charges on secondary electron emission avalanche evolution in vacuum surface flashover of spacecraft
Surface charging of dielectric materials is commonly observed in spacecraft under complex space environments. The accumulated charges on dielectric surfaces can modify the local electric-field distribution and subsequently affect secondary electron emission avalanche (SEEA), which plays a critical role in vacuum surface flashover. However, the influence mechanism of pre-existing surface charges formed before discharge initiation on the subsequent SEEA evolution remains insufficiently understood. In this work, a 2-spatial- and 3-velocity-dimensional particle-in-cell model is employed to investigate the effect of pre-existing negative surface charges near the cathode on vacuum surface flashover development. Different levels of localized negative surface charge densities are introduced as initial charging states, and their effects on electron emission, avalanche evolution, surface charge accumulation, and electric-field redistribution are systematically analyzed. The results demonstrate that the pre-existing charge of dielectric surfaces can strongly regulate subsequent vacuum flashover behavior, providing new insights into the coupling mechanism between surface charging and SEEA development in spacecraft and vacuum insulation systems.
- 10 August 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (6)
Influence of pre-existing negative surface charges on secondary electron emission avalanche evolution in vacuum surface flashover of spacecraft
Surface charging of dielectric materials is commonly observed in spacecraft under complex space environments. The accumulated charges on dielectric surfaces can modify the local electric-field distribution and subsequently affect secondary electron emission avalanche (SEEA), which plays a critical role in vacuum surface flashover. However, the influence mechanism of pre-existing surface charges formed before discharge initiation on the subsequent SEEA evolution remains insufficiently understood. In this work, a 2-spatial- and 3-velocity-dimensional particle-in-cell model is employed to investigate the effect of pre-existing negative surface charges near the cathode on vacuum surface flashover development. Different levels of localized negative surface charge densities are introduced as initial charging states, and their effects on electron emission, avalanche evolution, surface charge accumulation, and electric-field redistribution are systematically analyzed. The results demonstrate that the pre-existing charge of dielectric surfaces can strongly regulate subsequent vacuum flashover behavior, providing new insights into the coupling mechanism between surface charging and SEEA development in spacecraft and vacuum insulation systems.
- Open Access
- 25 March 2020
- Published by Georg Thieme Verlag KG in Synlett
- Vol. 31 (07)
Linked PDF of Table of Contents
- 25 March 2020
- Published by Georg Thieme Verlag KG in Synlett
- Vol. 31 (07)
Open AccessLinked PDF of Table of Contents
- 1 October 2018
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 89 (10) , 104706
A compact high-voltage pulse forming module with hundreds of nanoseconds quasi-squared output pulse
A pulse forming module (PFM) with a multifunction of energy storage and a quasi-squared pulse output is developed to meet the challenge of a compact design and square output waveform in a high-power Marx generator. A simplified pulse forming circuit comprising only 2 parallel connected LC sections, in which every section contains an inductor and a capacitor in series, has been proposed and investigated carefully to obtain a quasi-squared waveform. Influences of inductance values in the circuit on its output waveform to a resistive load are investigated. PFMs are designed and fabricated based on the 2 LC section circuit, in which series folded film capacitors are employed to achieve a high energy density of 0.04 J/cm3 at a charging voltage of 120 kV. The as-designed module can output a quasi-squared waveform with FWHM of about 180 ns and the flattop duration greater than 90 ns. It can work at a repetition rate as high as 50 Hz, while the output waveforms show small differences. This research has developed a PFM with a quasi-squared output waveform based on a simplified 2 LC section circuit, which shows potential to reduce the size of the high power generator system that is based on it.
- 1 October 2018
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 89 (10) , 104706
A compact high-voltage pulse forming module with hundreds of nanoseconds quasi-squared output pulse
A pulse forming module (PFM) with a multifunction of energy storage and a quasi-squared pulse output is developed to meet the challenge of a compact design and square output waveform in a high-power Marx generator. A simplified pulse forming circuit comprising only 2 parallel connected LC sections, in which every section contains an inductor and a capacitor in series, has been proposed and investigated carefully to obtain a quasi-squared waveform. Influences of inductance values in the circuit on its output waveform to a resistive load are investigated. PFMs are designed and fabricated based on the 2 LC section circuit, in which series folded film capacitors are employed to achieve a high energy density of 0.04 J/cm3 at a charging voltage of 120 kV. The as-designed module can output a quasi-squared waveform with FWHM of about 180 ns and the flattop duration greater than 90 ns. It can work at a repetition rate as high as 50 Hz, while the output waveforms show small differences. This research has developed a PFM with a quasi-squared output waveform based on a simplified 2 LC section circuit, which shows potential to reduce the size of the high power generator system that is based on it.
- 1 August 2014
- Published by Elsevier in Materials Letters
- Vol. 128, 132-135
Flexible free-standing graphene foam supported silicon films as high capacity anodes for lithium ion batteries
- 1 August 2014
- Published by Elsevier in Materials Letters
- Vol. 128, 132-135
Flexible free-standing graphene foam supported silicon films as high capacity anodes for lithium ion batteries
- 12 July 2013
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 15 (36) , 7298-7306
Synthesis of core–shell architectures of silicon coated on controllable grown Ni-silicide nanostructures and their lithium-ion battery application
Crystalline Ni3Si2 nanostructures were grown on nickel foams via a simple and high-yield chemical vapor deposition (CVD). The morphologies were found to be dependent on the growth pressure. The obtained nanostructures have good crystallinity and uniform distribution. After coating amorphous silicon (a-Si) layers onto the obtained Ni3Si2 nanostructures by an inductively coupled plasma CVD, the architectures were assembled as anodes for lithium-ion batteries. High initial reversible specific capacity of 3733 mA h g−1 is obtained for the prepared a-Si coated Ni3Si2 nanowire electrode at a current density of 2.1 A g−1. After 50 cycles, the specific capacity still stays at above 2000 mA h g−1. When the current density is as high as 8.4 A g−1, the specific capacity maintains at about 1500 mA h g−1. For such core–shell configuration electrodes, the inactive and metallic Ni3Si2 core conducts electrons and provides a mechanically stable anchoring basis for the a-Si layers, resulting in improved electrochemical performance.
- 12 July 2013
- Published by Royal Society of Chemistry (RSC) in CrystEngComm
- Vol. 15 (36) , 7298-7306
Synthesis of core–shell architectures of silicon coated on controllable grown Ni-silicide nanostructures and their lithium-ion battery application
Crystalline Ni3Si2 nanostructures were grown on nickel foams via a simple and high-yield chemical vapor deposition (CVD). The morphologies were found to be dependent on the growth pressure. The obtained nanostructures have good crystallinity and uniform distribution. After coating amorphous silicon (a-Si) layers onto the obtained Ni3Si2 nanostructures by an inductively coupled plasma CVD, the architectures were assembled as anodes for lithium-ion batteries. High initial reversible specific capacity of 3733 mA h g−1 is obtained for the prepared a-Si coated Ni3Si2 nanowire electrode at a current density of 2.1 A g−1. After 50 cycles, the specific capacity still stays at above 2000 mA h g−1. When the current density is as high as 8.4 A g−1, the specific capacity maintains at about 1500 mA h g−1. For such core–shell configuration electrodes, the inactive and metallic Ni3Si2 core conducts electrons and provides a mechanically stable anchoring basis for the a-Si layers, resulting in improved electrochemical performance.
- 1 December 2010
- Published by Elsevier in Applied Surface Science
- Vol. 257 (4) , 1342-1346
Effect of Ar in the source gas on the microstructure and optoelectronic properties of microcrystalline silicon films deposited by plasma-enhanced CVD
- 1 December 2010
- Published by Elsevier in Applied Surface Science
- Vol. 257 (4) , 1342-1346
Effect of Ar in the source gas on the microstructure and optoelectronic properties of microcrystalline silicon films deposited by plasma-enhanced CVD