Francyelle Calegari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Francyelle Calegari has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Luiz Humberto Marcolino Junior
Laboratório de Sensores Eletroquímicos (LabSensE), Departamento de Química, Universidade Federal do Paraná (UFPR), CEP 81.531-980, Curitiba, PR, Brazil
3 shared publications - Cláudia Eliana Bruno Marino
Universidade Federal do Paraná, Brasil
2 shared publications - João Tedim
CICECO-Aveiro Institute of Materials and Department of Materials and Ceramic Engineering, University of Aveiro, 3810-193 Aveiro, Portugal
2 shared publications Márcio F. Bergamini
2 shared publications- Mário Guerreiro Silva Ferreira
Department of Materials and Ceramic Engineering, CICECO - Aveiro institute of materials, University of Aveiro, 3810-193 Aveiro, Portugal
2 shared publications - Aldo Jose Gorgatti Zarbin
Department of Chemistry, Federal University of Paraná (UFPR), Centro Politécnico, CP 19032, 81531-980, Curitiba, PR, Brazil
1 shared publication
Latest Publications
- Open Access
- 9 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 1800
Influence of the Operating Conditions on the Release of Corrosion Inhibitors from Spray-Dried Carboxymethylcellulose Microspheres
Sodium carboxymethylcellulose (CMC-Na) microparticles, containing corrosion inhibitor benzotriazole (BTA), were prepared using different spray drying processing parameters, with the purpose of future application in protective coatings for the delivery of corrosion inhibitors. The effects of the processing parameters, such as inlet temperature and spray flow rate, are discussed herein. The biopolymeric CMC-Na microparticles obtained were characterized morphologically by SEM and TEM, and their release profile studied by UV-Vis. The results show that the prepared microparticles (microspheres) were homogeneous, spherically shaped and of a matrix-type nature. Additionally, it was observed that the inlet temperature and spray flow rate significantly influenced the release profiles and process yields. From the different process parameters tested, it was found that the best conditions to achieve higher process yields, higher encapsulation efficiencies and better release properties, were an inlet temperature of 170 °C, a pump rate of 2.5 mL/min, and a drying air-flow rate of 440 L/h.
- 9 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 1800
Open AccessInfluence of the Operating Conditions on the Release of Corrosion Inhibitors from Spray-Dried Carboxymethylcellulose Microspheres
Sodium carboxymethylcellulose (CMC-Na) microparticles, containing corrosion inhibitor benzotriazole (BTA), were prepared using different spray drying processing parameters, with the purpose of future application in protective coatings for the delivery of corrosion inhibitors. The effects of the processing parameters, such as inlet temperature and spray flow rate, are discussed herein. The biopolymeric CMC-Na microparticles obtained were characterized morphologically by SEM and TEM, and their release profile studied by UV-Vis. The results show that the prepared microparticles (microspheres) were homogeneous, spherically shaped and of a matrix-type nature. Additionally, it was observed that the inlet temperature and spray flow rate significantly influenced the release profiles and process yields. From the different process parameters tested, it was found that the best conditions to achieve higher process yields, higher encapsulation efficiencies and better release properties, were an inlet temperature of 170 °C, a pump rate of 2.5 mL/min, and a drying air-flow rate of 440 L/h.
- 4 April 2019
- Published by Royal Society of Chemistry (RSC) in Analytical Methods
- Vol. 11 (18) , 2422-2427
A carbon black composite electrode for flow injection amperometric determination of hydrochlorothiazide
This work describes a composite electrode based on carbon black (CB) and poly(ethylene-co-vinyl)acetate (EVA) for development of a robust, low cost and time-saving method for the amperometric determination of hydrochlorothiazide (HCTZ) in a pharmaceutical formulation and synthetic human urine samples. This composite electrode exhibits favourable features such as mechanical resistance, low cost and simple preparation. The proposed electrode was used as an amperometric detector in flow injection analysis (FIA) based on HCTZ oxidation. The best amperometric responses were obtained by employing a composite electrode made with 75% (w/w) carbon black (CB) and 25% (w/w) poly(ethylene-co-vinyl)acetate (EVA), sample volume of 100 μL, flow rate of 5.3 mL min−1 and potential of detection of +900 mV vs. Ag/AgCl/3.0 mol L−1. Under optimized conditions, it was possible to achieve an analytical frequency of 128 injections h−1, a linear dynamic range (LDR) of 10 to 200 μmol L−1, a limit of quantification (LOQ) of 4.4 μmol L−1 and a limit of detection (LOD) of 1.3 μmol L−1 for HCTZ. The proposed method was successfully applied for determination of HCTZ in commercial tablets and synthetic human urine samples without any chemical pretreatment. The composite electrode based on EVA and carbon black is feasible and totally adaptable to portable devices for HCTZ quantification.
- 4 April 2019
- Published by Royal Society of Chemistry (RSC) in Analytical Methods
- Vol. 11 (18) , 2422-2427
A carbon black composite electrode for flow injection amperometric determination of hydrochlorothiazide
This work describes a composite electrode based on carbon black (CB) and poly(ethylene-co-vinyl)acetate (EVA) for development of a robust, low cost and time-saving method for the amperometric determination of hydrochlorothiazide (HCTZ) in a pharmaceutical formulation and synthetic human urine samples. This composite electrode exhibits favourable features such as mechanical resistance, low cost and simple preparation. The proposed electrode was used as an amperometric detector in flow injection analysis (FIA) based on HCTZ oxidation. The best amperometric responses were obtained by employing a composite electrode made with 75% (w/w) carbon black (CB) and 25% (w/w) poly(ethylene-co-vinyl)acetate (EVA), sample volume of 100 μL, flow rate of 5.3 mL min−1 and potential of detection of +900 mV vs. Ag/AgCl/3.0 mol L−1. Under optimized conditions, it was possible to achieve an analytical frequency of 128 injections h−1, a linear dynamic range (LDR) of 10 to 200 μmol L−1, a limit of quantification (LOQ) of 4.4 μmol L−1 and a limit of detection (LOD) of 1.3 μmol L−1 for HCTZ. The proposed method was successfully applied for determination of HCTZ in commercial tablets and synthetic human urine samples without any chemical pretreatment. The composite electrode based on EVA and carbon black is feasible and totally adaptable to portable devices for HCTZ quantification.
- 21 June 2011
- Published by American Chemical Society (ACS) in Journal of Agricultural and Food Chemistry
- Vol. 59 (14) , 7620-7625
Voltammetric Determination of the Antioxidant Capacity in Wine Samples Using a Carbon Nanotube Modified Electrode
A direct determination of gallic acid was achieved at a carbon paste electrode modified with carbon nanotubes under differential pulse voltammetry conditions. The values obtained for gallic acid were used to estimate the antioxidant properties of the wine sample based on gallic acid oxidation. The proposed method is based on the gallic acid oxidation process at a modified carbon paste electrode (MCPE) containing 30% (m/m) of carbon nanotubes monitored at 0.35 V versus Ag/AgCl (KCl 3 mol L–1). Using the optimized experimental conditions, the calibration curve for gallic acid was linear in the concentration range from 5.0 × 10–7 to 1.5 × 10–5 mol L–1 with a detection limit of 3.0 × 10–7 mol L–1. The MCPE was successfully applied for the determination of the antioxidant capacity for red and white wine samples without interference of glucose and ascorbic acid, and the obtained results were compared with the standard spectrophotometric method.
- 21 June 2011
- Published by American Chemical Society (ACS) in Journal of Agricultural and Food Chemistry
- Vol. 59 (14) , 7620-7625
Voltammetric Determination of the Antioxidant Capacity in Wine Samples Using a Carbon Nanotube Modified Electrode
A direct determination of gallic acid was achieved at a carbon paste electrode modified with carbon nanotubes under differential pulse voltammetry conditions. The values obtained for gallic acid were used to estimate the antioxidant properties of the wine sample based on gallic acid oxidation. The proposed method is based on the gallic acid oxidation process at a modified carbon paste electrode (MCPE) containing 30% (m/m) of carbon nanotubes monitored at 0.35 V versus Ag/AgCl (KCl 3 mol L–1). Using the optimized experimental conditions, the calibration curve for gallic acid was linear in the concentration range from 5.0 × 10–7 to 1.5 × 10–5 mol L–1 with a detection limit of 3.0 × 10–7 mol L–1. The MCPE was successfully applied for the determination of the antioxidant capacity for red and white wine samples without interference of glucose and ascorbic acid, and the obtained results were compared with the standard spectrophotometric method.