ADAndrii Dreus

Andrii Dreus

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Andrii Dreus has a total of 78 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of wind turbine blade trailing edge modification on aerodynamic noise

    by Serhii Aleksieienko, Andrii Dreus, Lilia Nakashydze, Vitalii Derbaba, Serhii Zolotarenko

    This study investigates acoustic processes that occur during the flow of air around the blade segment of a wind turbine. The issue of aerodynamic noise generated by wind turbines is one of the factors that hinders the widespread implementation of wind turbines. Noise reduction is possible by changing the design of the turbine blade to influence the aerodynamic processes during the flow of air around it. This paper reports an experimental study on the possibility of reducing the aerodynamic noise of wind turbines by modifying the trailing edge of the blade. An original methodology of acoustic experiments in an anechoic chamber is described; the results of experimental studies are given. Two different modifications of serrated trailing edges of the blade with the NACA0012 aerodynamic profile have been considered: a flat serrated edge and a three-dimensional serrated edge. The results from aerodynamic noise measurements of the prototypes of the blade segments were compared with the noise from the basic original sample. Acoustic measurements were carried out in the range of flow speeds: 7.5–20 m/s and angles of attack 0–15°. The results demonstrated that both configurations of the serrated trailing edge make it possible to reduce the level of aerodynamic noise compared to the base segment. It was found that the noise reduction occurs at relatively small angles of attack (0–5°) and moderate flow speeds (up to 15 m/s). In the specified range of parameters, the reduction of aerodynamic noise occurred due to a decrease in the sound pressure level in a certain frequency range by up to 4 dB. The segment with flat serrations turned out to be somewhat more effective in terms of noise reduction in the low-frequency range. Results of this work could be used when designing new generation wind energy systems with reduced noise levels, as well as other aerodynamic devices.

  • Methodology of the acoustic experiment for studying the aerodynamic noise of wind turbine blade segments

    by S. V Aleksieienko, A. Yu Dreus, L. V Nakashydze, V. A Derbaba, S. A Zolotarenko

    Purpose. This work focuses on developing and implementing the methodology for studying the aerodynamic noise generated by the rotor of a wind turbine. The acoustic characteristics of this noise are analyzed using a blade segment with NACA0012 airfoil. The study addresses the ongoing challenge of reducing wind turbine noise in renewable energy systems. Methodology. The aerodynamic noise of a wind turbine blade segment was experimentally investigated under laboratory conditions in an anechoic chamber. The measurement procedure complies with the national standard DSTU GOST ISO 5725-1:2005. Findings. The paper provides a brief overview of existing approaches to studying aerodynamic noise from wind turbines and presents a custom-designed experimental setup for studying acoustic noise characteristics of blade segments in an anechoic chamber. A method is proposed for analyzing both the acoustic signals of interest and the background noise components. Sound pressure levels were measured, and spectral characteristics of the noise generated by the blade segment with NACA0012 airfoil were analyzed in the presence of background noise. The method demonstrated effective operability for laboratory-based acoustic studies. Originality. The proposed method represents an original approach that differs from the traditional ones, in which test sections are integrated into an anechoic acoustic environment. Unlike conventional methods that assume a stationary model position and reversed flow conditions, this setup simulates the rotational motion of the blade airfoil. This enables a more realistic replication of operational rotor conditions and yields experimental data that better reflect actual aerodynamic noise behavior. Practical value. The developed methodology and experimental setup are applicable to parametric studies of various blade profiles to identify noise-reducing blade modifications. The results are also valuable for validating numerical models of aerodynamic noise prediction for turbine blades.


  • Open Access

    Estimating the degree of disposal of a launch vehicle casing made from polyolefins in the earth’s atmosphere

    by Mykola Dron, Erik Lapkhanov, Aleksandr Golubek, Andrii Dreus, Olena Kositsyna, Ludmila Dubovik

    The object of this study is the process of disposing of the upper stage body of a launch vehicle made of polyolefins by burning in the dense layers of the Earth’s atmosphere during removal from Earth orbit. The task addressed was to determine the possibility of disposal of the upper stage bodies of launch vehicles made of polyolefins during deorbiting. The mathematical model built makes it possible to take into account the effect of ballistic and aerothermodynamic aspects at the same time. The application of this model makes it possible to estimate the degree of disposal of the upper stage bodies of launch vehicles made of polyolefins in the Earth’s atmosphere at the stage of scientific research. In turn, this makes it possible to rationally choose the design parameters of materials for launch vehicle bodies, taking into account the disposal phase in the dense layers of the atmosphere, as well as rationally select the initial parameters for deorbiting orbits. This makes it possible to maximize the level of disposal and minimize the probability of debris falling on uninhabited areas of the Earth. The results of the study showed that launch vehicle bodies made of polymer materials such as polyethylene and polypropylene could burn up in the atmospheric part of the trajectory by 90–100 %, depending on the mass-dimensional characteristics and the type of orbit. In turn, increasing the ellipticity of the orbit makes it possible to increase the steepness of the entry of the upper body of the launch vehicle into the dense layers of the atmosphere, and hence, to increase the heat flows that contribute to the combustion of the body. With this in mind, methodological recommendations have been compiled for choosing orbits of the necessary ellipticity, taking into account the place of fall of fragments of the upper bodies of carrier rockets that did not burn up in the atmosphere


  • Open Access

    Prospects for the creation of small-sized high-speed unmanned aerial vehicles based on WIG-craft

    by Andrii Dreus, Sergey Alekseyenko, Oleksii Kulyk, Valeriі Nekrasov

    WIG-craft are high-speed vehicles that use the dynamic principle of support above the ground. Today, the current examples and projects of such vessels concern, mainly, only large-sized or medium-sized manned vehicles, for which it is possible to ensure stable aerodynamic characteristics during flight. At the same time, modern trends in the development of vehicles indicate a growing interest in small unmanned vehicles. Currently, the issue of creating small manned and unmanned WIG-crafts has become relevant. In the presented work, based on the von Karman–Gabrielli methodology, the efficiency of transport WIG-craft among other types of vehicles was evaluated. The possibility of using such small-sized devices as unmanned devices is considered. The productivity of a WIG-craft is depends on its aerodynamic characteristics. Scale factor is very important for WIG-craft, because the aerodynamics is depended on wings size. The design of a small-sized WIG-craft based on the aerodynamic scheme of an airplane is proposed. The aerodynamic characteristics of the proposed device were evaluated using CFD modeling. Outcomes indicates that the aerodynamic properties of a ship are greatly affected by clearance and velocity. Ground effect is allowed to increase the aerodynamic quality up to 1.5 times, provide the transport of payloads at velocities as high as 250 km/h with a take-off weight of 2.7 tons. The analysis of computation results shows that the proposed project of an unmanned WIG-craft is fully operational and promising for solving the problems of high-speed delivery of small payloads. According to the computation results of the aerodynamic characteristics, the specific power of the device was determined, which indicates the high theoretical efficiency of the proposed means.


  • Open Access

    Analysis of the acoustic emission of a modified segment of a wind turbine blade with a NACA 0012 airfoil

    by Andrii Dreus, Vitalii Derbaba, Dmytro Harkavenko, Serhii Aleksieienko

    The relevance of the study is due to the need to reduce the noise pollution that occurs during the operation of wind power plants, in particular, in densely populated or environmentally sensitive regions. One of the promising approaches to reducing the acoustic radiation of wind turbine blades is the modification of their geometry to control turbulent flow structures. This paper presents the methodology and results of an experimental study of aerodynamic noise generated by a NACA0012 blade profile. The effect of periodic notches on the trailing edge on the acoustic characteristics of the profile is studied. The aim of the work is to assess the effectiveness of the notched trailing edge in reducing the level of aerodynamic noise. The study was conducted in an anechoic chamber using physical models of the profile manufactured by 3D printing, and acoustic measurements were performed using a sound level meter with subsequent data processing using the Fast Fourier Transform (FFT) method. The experiments covered different incident flow velocities (from 10 to 20 m/s) and angles of attack (0° and 5°), and the results are presented in the form of sound pressure spectra. It was found that the modified profile provides a reduction in the sound pressure level of up to 7 dB compared to the standard profile. The effect is especially pronounced in the frequency range up to 8 kHz, typical of vortex noise sources at relatively low flow velocities. The proposed approach demonstrates high efficiency and can be applied to optimize the designs of wind turbines, as well as other rotating elements, such as UAV propellers or fans.

  • Open Access

    Identification of heat loads on space objects re-entering thee Earth's atmosphere using machine learning methods

    by Volodymyr Strembovskyi, Andrii Dreus

    The article is devoted to the problem of predicting thermal loads on space objects during reentry.The intensive development of near-Earth space leads to a steady increase in the number of artificial non-functional space objects in Earth orbit, which requires the search for effective methods of space debris removal.Some active and combined methods of space debris removal provide for the possibility of controlling the parameters of re-entry and the impact on the thermal regime of the object.Predicting the amount of heat is important for determining the effectiveness of thermal destruction of an object.The purpose of this work is to assess the possibility of using modern artificial intelligence methods to determine the amount of heat received by a space object while moving in the atmosphere.To solve this task, three popular machine learning algorithms were applied:Support Vector Regression (SVR), Multilayer Perceptron (MLP) and Decision Tree Regression (DTR).Based on a dataset that includes information on entry time, altitude, speed, and air density, machine learning models were trained and compared.Metrics were used to evaluate the prediction accuracy: , mean absolute percentage error, and root mean square error.The results of the study showed that MLP and DTR algorithms demonstrated high forecasting accuracy.MLP and DTR models can be effectively used to predict thermal loads on space objects.In the future, the results obtained can be the basis for creating an effective tool for predicting head load on a space object.

  • Open Access

    Rationale for choosing the airfoil of a UAV wing using a dynamic ground effect principle

    by Andrii Dreus, Olena Kravets

    Vehicles that use the principle of dynamic ground effect principle are innovative vehicles that have prospects for use as high-speed unmanned vehicles. It is known that when an aircraft moves near the ground, the phenomenon of increasing lift occurs, which allows for contactless movement at high speeds. However, the effectiveness of this ground effect depends on the airfoil shape. The object of this study is the aerodynamic processes that occur during the movement of an unmanned aerial vehicle near the ground. The influence of the effect of approaching the ground on the aerodynamic characteristics of four airfoil of different shapes has been considered: Clark YH-12, NACA-M6, USA-35B, TsAGI-721, which are used in subsonic high-speed aircraft, including unmanned aerial vehicles. The aim of the work is to evaluate the performance of these aerodynamic airfoils in near-surface operation and to determine the most promising shape for use in small unmanned WIGs. CFD modeling methods were used as a research tool. The pressure and velocity fields around the wing airfoils were determined and the influence of the distance to the ground and the angle of attack on the aerodynamic characteristics was established. It was found that the best aerodynamic quality for all airfoils is achieved at angles of attack of 4–6°. It is not recommended to use airfoils with angles of attack close to 0° as the ground may have a negative effect on lift. The USA-35B airfoil demonstrated the greatest increase in aerodynamic quality when approaching the surface, with a maximum increase of 67 %. This makes it possible to recommend USA-35B as small unmanned aerial vehicles with a dynamic ground effect principle


  • Open Access

    Determining the aerodynamic performance of a high-speed unmanned marine wig craft

    by Andrii Dreus, Serhii Aleksieienko, Valerii Nekrasov

    The study object of this paper is the aerodynamic processes during the movement of an unmanned aerial vehicle flying low over the underlying surface. The ground effect is known to enhance the aerodynamic performance of low-flying aircraft, particularly larger ones. However, this effect is most noticeable for large objects. Unmanned vehicles are typically characterized by their relatively compact geometry. This study explores the aerodynamic processes involved in the flight of a small-sized vehicle using the principle of dynamic support over a surface. The particular prototype of the unmanned aerial vehicle suggested by the authors has been examined herein. The aim of the study is to evaluate the aerodynamic forces affecting a small-sized unmanned high-speed vehicle that employs the dynamic principle of support over the surface (WIG craft) by using CFD modeling. In contrast to most available studies on the ground effect, a 3D problem statement was used in this work. Computational experiments have visualized the physical fields surrounding an aircraft in flight over the ground. This study determines how the distance from the surface affects the aerodynamic properties of a small-sized aircraft, as well as the height of the effective zone where ground effect influences the small-sized WIG craft within . It has been shown that approaching the surface leads to a shift in the center of pressure of the vehicle, which leads to a change in aerodynamic momentum. This phenomenon must be taken into account when designing a control system to provide a stable flight. The study's findings are directly relevant for the development of a type of unmanned vehicles that use the dynamic principle of support over the surface.


  • Open Access

    Assessing the possibility of using a variable-length launch vehicle with a polymer body for orbiting payload

    by Aleksandr Golubek, Serhii Aleksieienko, Mykola Dron, Andrii Dreus

    The object of this study was the motion of an ultralight class variable-length launch vehicle made of a polymer body along the active phase of the trajectory. The work considers the solution to the problem of designing low-cost means of delivery to orbit, namely to the assessment of the possibility of removing the payload by a carrier rocket with a polymer body of variable length beyond the dense atmosphere of the Earth. For this purpose, ballistic projection of the trajectory of the launch vehicle was carried out taking into account overloading; its aerodynamic characteristics and peculiarities of aerothermodynamic processes occurring during flight in the atmospheric phase of the trajectory were determined. The closeness (up to 10 %) of the obtained results with known experimental data is shown. The influence of the aerodynamic force on the parameters of the launch vehicle motion was studied. A flight simulation was conducted, the results of which showed the fundamental possibility of launching a CubeSat 24U class payload using a launch vehicle with a polymer body of variable length to a suborbital trajectory with an altitude of about 300 km. At the same time, the effective longitudinal overload on the body of the launch vehicle does not exceed 4 units, and the temperature on the surface of the body does not exceed 300 K. A feature of the research is the use of a multidisciplinary approach, which implies taking into account the interrelationship of aerodynamic, thermodynamic, and ballistic processes. The established motion parameters, aerodynamic characteristics, and the surface heating temperature of the launch vehicle body are key values for further research on the design and analysis of a launch vehicle with a polymer body of variable length. These data could be used to calculate the mechanical and thermal loads acting on the structure of the launch vehicle during flight