Mahfodzah Md Padzi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Mahfodzah Md Padzi has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Shahrum Abdullah
Universiti Kebangsaan Malaysia, UKM
7 shared publications Mohd Zaki Nuawi
Universiti Kebangsaan Malaysia
6 shared publicationsShahrum Abdullah
Selangor, Malaysia
5 shared publicationsM. Z. Nuawi
Universiti Kebangsaan Malaysia
2 shared publicationsA. Arifin
1 shared publicationA. K. Ariffin
1 shared publication
Latest Publications
- 10 July 2025
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 24 (2) , 210-219
Experiment and simulation to investigate fatigue life of R260 of LRT
- 10 July 2025
- Published by Taylor & Francis in Australian Journal of Mechanical Engineering
- Vol. 24 (2) , 210-219
Experiment and simulation to investigate fatigue life of R260 of LRT
- Open Access
- 22 September 2022
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 16 (62) , 271-278
Evaluation on fatigue behaviour of spot-welded joint under low blow impact treatment
Welding is used widely in modern industries to combine parts needed complete a product. In this paper, we investigated the effect of post-weld impact treatment (PWIT) on spot-weld joints and evaluate the tensile and fatigue properties of the specimens. Currently, there is no simple failure criterion capable of predicting the strength of a spot weld under different loading conditions. The reliability of spot-welded structures treated with PWIT in terms of fatigue integrity could be understood more by the end of this research. The result showed that not only the tensile properties of PWIT specimens give an improvement, but there was also a significant increase in the fatigue life of the treated specimens.
- 22 September 2022
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 16 (62) , 271-278
Open AccessEvaluation on fatigue behaviour of spot-welded joint under low blow impact treatment
Welding is used widely in modern industries to combine parts needed complete a product. In this paper, we investigated the effect of post-weld impact treatment (PWIT) on spot-weld joints and evaluate the tensile and fatigue properties of the specimens. Currently, there is no simple failure criterion capable of predicting the strength of a spot weld under different loading conditions. The reliability of spot-welded structures treated with PWIT in terms of fatigue integrity could be understood more by the end of this research. The result showed that not only the tensile properties of PWIT specimens give an improvement, but there was also a significant increase in the fatigue life of the treated specimens.
- 1 January 2022
- Published by Springer Nature
- p. 185-194
Mechanical Characteristics of Fly Ash-Based Geopolymer Bricks
- 1 January 2022
- Published by Springer Nature
- p. 185-194
Mechanical Characteristics of Fly Ash-Based Geopolymer Bricks
- Open Access
- 29 November 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 269 (1) , 012060
Fatigue Characteristics of 3D Printed Acrylonitrile Butadiene Styrene (ABS)
Recently, the use of 3D printer technology has become significant to industries, especially when involving the new product development. 3D printing is a technology, which produces the 3D product or prototype using a layer-by-layer technique. However, there becomes less research on the mechanical performance of the 3D printed component. In the present work, fatigue characteristics of 3D printed specimen have been studied. Acrylonitrile butadiene styrene (ABS) has been chosen as a material research due to its wide applications. Two types of specimen used, which is the 3D printing and moulding specimens. Fused deposition modelling (FDM) technique was used to produce the specimens. The dog bone shape part was produced based on ASTM D638 standard and the tensile test has been carried out to get the mechanical properties. Fatigue test was carried out at 40%, 60% and 80% of the tensile strength. The moulded part shows higher fatigue cycles compared to 3D printed part for all loading percentages. Fatigue lives for 40%, 60% and 80%, were 911, 2645 and 26948 cycles, respectively. The results indicated that 3D printed part has a lower fatigue life, which may not suitable for industrial applications. However, the 3D printed part could be improved by using various parameters and may be introduced in low strength application.
- 29 November 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 269 (1) , 012060
Open AccessFatigue Characteristics of 3D Printed Acrylonitrile Butadiene Styrene (ABS)
Recently, the use of 3D printer technology has become significant to industries, especially when involving the new product development. 3D printing is a technology, which produces the 3D product or prototype using a layer-by-layer technique. However, there becomes less research on the mechanical performance of the 3D printed component. In the present work, fatigue characteristics of 3D printed specimen have been studied. Acrylonitrile butadiene styrene (ABS) has been chosen as a material research due to its wide applications. Two types of specimen used, which is the 3D printing and moulding specimens. Fused deposition modelling (FDM) technique was used to produce the specimens. The dog bone shape part was produced based on ASTM D638 standard and the tensile test has been carried out to get the mechanical properties. Fatigue test was carried out at 40%, 60% and 80% of the tensile strength. The moulded part shows higher fatigue cycles compared to 3D printed part for all loading percentages. Fatigue lives for 40%, 60% and 80%, were 911, 2645 and 26948 cycles, respectively. The results indicated that 3D printed part has a lower fatigue life, which may not suitable for industrial applications. However, the 3D printed part could be improved by using various parameters and may be introduced in low strength application.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1901, 050004
Effect of post weld impact treatment (PWIT) on mechanical properties of spot-welded joint
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1901, 050004
Effect of post weld impact treatment (PWIT) on mechanical properties of spot-welded joint
- Open Access
- 1 June 2016
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in International Journal of Automotive and Mechanical Engineering
- Vol. 13 (1) , 3262-3277
Characterization of the biaxial fatigue behaviour on medium carbon steel using the strain-life approach
This study aims to investigate the fatigue behaviour and determine the fatigue life prediction under biaxial loading. Fatigue tests were performed according to ASTM 2207-02 and the values of tensile stresses are selected from the ultimate tensile strength which is 0.5 Su, 0.6 Su, 0.7 Su, 0.8 Su and 0.9 Su, while the torsion angle representing the shear stresses acting was set at 15 degrees. The biaxial fatigue test was conducted using a combination of two types of stresses acting on the same frequency, namely 1 Hz, on smooth specimens made from medium carbon steel. The biaxial fatigue lives of the specimens are recorded when the specimen has completely fractured. The results indicate that the observed fatigue lives are in good agreement with the predicted lives by using the Coffin–Manson, Morrow, and Smith–Watson–Topper strain-based models. Mohr’s circle approach was used to determine the maximum shear stress and principal normal stress. The maximum shear stress increased from 457 MPa to 486 MPa with the increment of principal normal stress from 612 MPa to 767 MPa. The principal stresses, maximum shear stresses, and energy dissipated were used to explain and describe the behaviour of biaxial fatigue. Both stresses are inversely proportional to the fatigue life. Meanwhile, the energy is linearly proportional to the stress applied, where the values increase in the range 500 kJ/m3 to 605 kJ/m3 . Thus, the basic understanding of the material behaviour may be used in the processes of declaring component service lives and the fatigue life prediction of a particular automotive component. Therefore, the cost incurred can be reduced for the development process in material engineering.
- 1 June 2016
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in International Journal of Automotive and Mechanical Engineering
- Vol. 13 (1) , 3262-3277
Open AccessCharacterization of the biaxial fatigue behaviour on medium carbon steel using the strain-life approach
This study aims to investigate the fatigue behaviour and determine the fatigue life prediction under biaxial loading. Fatigue tests were performed according to ASTM 2207-02 and the values of tensile stresses are selected from the ultimate tensile strength which is 0.5 Su, 0.6 Su, 0.7 Su, 0.8 Su and 0.9 Su, while the torsion angle representing the shear stresses acting was set at 15 degrees. The biaxial fatigue test was conducted using a combination of two types of stresses acting on the same frequency, namely 1 Hz, on smooth specimens made from medium carbon steel. The biaxial fatigue lives of the specimens are recorded when the specimen has completely fractured. The results indicate that the observed fatigue lives are in good agreement with the predicted lives by using the Coffin–Manson, Morrow, and Smith–Watson–Topper strain-based models. Mohr’s circle approach was used to determine the maximum shear stress and principal normal stress. The maximum shear stress increased from 457 MPa to 486 MPa with the increment of principal normal stress from 612 MPa to 767 MPa. The principal stresses, maximum shear stresses, and energy dissipated were used to explain and describe the behaviour of biaxial fatigue. Both stresses are inversely proportional to the fatigue life. Meanwhile, the energy is linearly proportional to the stress applied, where the values increase in the range 500 kJ/m3 to 605 kJ/m3 . Thus, the basic understanding of the material behaviour may be used in the processes of declaring component service lives and the fatigue life prediction of a particular automotive component. Therefore, the cost incurred can be reduced for the development process in material engineering.
- 4 January 2014
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 57, 405-415
On the need to decompose fatigue strain signals associated to fatigue life assessment of the AISI 1045 carbon steel
- 4 January 2014
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 57, 405-415
On the need to decompose fatigue strain signals associated to fatigue life assessment of the AISI 1045 carbon steel
- 1 January 2014
- Published by Springer Nature in Journal of Central South University
- Vol. 21 (1) , 232-241
Evaluating ultrasound signals of carbon steel fatigue testing using signal analysis approaches
- 1 January 2014
- Published by Springer Nature in Journal of Central South University
- Vol. 21 (1) , 232-241
Evaluating ultrasound signals of carbon steel fatigue testing using signal analysis approaches
- 1 December 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 471, 235-240
Fatigue Damage Assessment Correlating with I-Kaz Coefficient
This paper describes the correlation between fatigue life with the I-kaz coefficients. Fatigue tests were performed according to the ASTM E466-96 standard with a strain gauge attached to the specimen being tested. AISI 1045 carbon steel was used as the material for this test due to its wide applications in the automotive and machinery industry. Fatigue tests were carried out at several constant loading stresses of 610 MPa, 650 MPa and 690 MPa at the sampling frequency of 8 Hz. A set of data acquisition system was used to collect the fatigue strain signals. The integrated Kurtosis-based algorithm for Z-filter (I-kaz) technique had been used to find the I-kaz coefficient. The I-kaz coefficient is found to have a good correlation with fatigue life, other than can represent fatigue damage.
- 1 December 2013
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 471, 235-240
Fatigue Damage Assessment Correlating with I-Kaz Coefficient
This paper describes the correlation between fatigue life with the I-kaz coefficients. Fatigue tests were performed according to the ASTM E466-96 standard with a strain gauge attached to the specimen being tested. AISI 1045 carbon steel was used as the material for this test due to its wide applications in the automotive and machinery industry. Fatigue tests were carried out at several constant loading stresses of 610 MPa, 650 MPa and 690 MPa at the sampling frequency of 8 Hz. A set of data acquisition system was used to collect the fatigue strain signals. The integrated Kurtosis-based algorithm for Z-filter (I-kaz) technique had been used to find the I-kaz coefficient. The I-kaz coefficient is found to have a good correlation with fatigue life, other than can represent fatigue damage.
- 25 October 2013
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 65 (1)
Ultrasound Signals Response Associated to Fatigue Failure Behaviour using Statistical Analysis
In this paper, ultrasound signals had been analysed using a statistical-based approach to evaluate and predict fatigue failure of carbon steel AISI 1045. Fatigue tests were performed according to the ASTM E466-96 standard with the attachment of an ultrasound sensor to the tested specimen. The material used in this test was the AISI 1045 carbon steel due to its extensive application in automotive and machinery industry. Fatigue test was carried out at a constant loading stress at the sampling frequency of 8 Hz. A set of data acquisition system was used to collect those fatigue ultrasound signals. All obtained data were analysed using specific software. Ultrasound signals were collected during fatigue test in order to detect any structural changes occurs during the test. Fatigue damage characteristics were observed based on the ultrasound signals characteristics and a further analysis was performed using statistical approach. The results of signals distribution, r.m.s value and energy content of the signals were discussed to correlate fatigue failure behaviour and ultrasound signals.
- 25 October 2013
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 65 (1)
Ultrasound Signals Response Associated to Fatigue Failure Behaviour using Statistical Analysis
In this paper, ultrasound signals had been analysed using a statistical-based approach to evaluate and predict fatigue failure of carbon steel AISI 1045. Fatigue tests were performed according to the ASTM E466-96 standard with the attachment of an ultrasound sensor to the tested specimen. The material used in this test was the AISI 1045 carbon steel due to its extensive application in automotive and machinery industry. Fatigue test was carried out at a constant loading stress at the sampling frequency of 8 Hz. A set of data acquisition system was used to collect those fatigue ultrasound signals. All obtained data were analysed using specific software. Ultrasound signals were collected during fatigue test in order to detect any structural changes occurs during the test. Fatigue damage characteristics were observed based on the ultrasound signals characteristics and a further analysis was performed using statistical approach. The results of signals distribution, r.m.s value and energy content of the signals were discussed to correlate fatigue failure behaviour and ultrasound signals.