Morgane Mokhtari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Morgane Mokhtari has a total of 69 co-authors. Here are the top co-authors by number of shared publications:
Eric Maire
6 shared publicationsHidemi Kato
Institute for Materials Research Tohoku University Sendai 980-8577 Japan
6 shared publications- Joël Alexis
LGP, UTTOP, University of Toulouse, 65000 Tarbes, France
6 shared publications Takeshi Wada
6 shared publicationsJannick Duchet-Rumeau
5 shared publications- Yannick Balcaen
LGP, UTTOP, University of Toulouse, 65000 Tarbes, France
5 shared publications
Latest Publications
- Open Access
Microstructure, Room and High-Temperature Mechanical Properties of As-Built PBF-LB W360 Hot Forming Steel Alloy
To produce increasingly efficient tools with optimized geometry, additive manufacturing is a suitable solution. However, tool steels, due to their high amount of carbon and hardening elements, may be unweldable and therefore difficult to produce using additive manufacturing methods that employ melting. W360 is a hot-forming alloy, and, in this study, it was produced through laser powder bed fusion (PBF-LB). The microstructure and mechanical properties were evaluated on as-built netshape PBF-LB samples. Despite the presence of many alloying elements, this alloy was not sensitive to cracks, and very good results from the defect analysis (defect surface density < 0.2%) were achieved. Microstructure and hardness are homogeneous in the sample except in the last layer due to an upskin effect. As-built netshape samples exhibit very promising mechanical properties up to 400 °C, which could be further improved by heat treatments.
Open AccessMicrostructure, Room and High-Temperature Mechanical Properties of As-Built PBF-LB W360 Hot Forming Steel Alloy
To produce increasingly efficient tools with optimized geometry, additive manufacturing is a suitable solution. However, tool steels, due to their high amount of carbon and hardening elements, may be unweldable and therefore difficult to produce using additive manufacturing methods that employ melting. W360 is a hot-forming alloy, and, in this study, it was produced through laser powder bed fusion (PBF-LB). The microstructure and mechanical properties were evaluated on as-built netshape PBF-LB samples. Despite the presence of many alloying elements, this alloy was not sensitive to cracks, and very good results from the defect analysis (defect surface density < 0.2%) were achieved. Microstructure and hardness are homogeneous in the sample except in the last layer due to an upskin effect. As-built netshape samples exhibit very promising mechanical properties up to 400 °C, which could be further improved by heat treatments.
- Open Access
- 27 February 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (3) , 84
Defects, Microstructure, and Hardness of As-Built and Heat-Treated 13 Hot Work Tool Steel and 17-4 PH Stainless Steel Obtained by Fused Filament Fabrication
Fused Filament Fabrication (FFF) is a low-cost additive manufacturing process that produces metallic parts from printing with a metal-polymer filament, followed by a debinding–sintering process. It presents an opportunity for the tooling sector to improve performance by geometrical optimization while keeping costs low. This study investigates the possibility of producing a molding core for plastic injection by FFF technology. This research aimed to characterize 17-4 PH stainless steel and H13 hot work tool steels produced through this process. Their heat treatment behavior was investigated using dilatometry, which led to the obtention of a Continuous Cooling Transformation (CCT) diagram. Results show that for as-sintered materials, martensitic steel with some residual austenite is present in 17-4 PH, and a pearlitic microstructure is observed in H13. Porosity (around 4%) falls within the reported range in the literature and can be removed by hot isostatic pressing. CCT diagrams do not show significant differences with conventional materials. The low hardness of as-sintered H13 (around 175 HV1) is improved (>500 HV1) by suitable heat treatment. Finally, both materials meet the requirements for this specific industrial application, and demonstrators were produced.
- 27 February 2026
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 10 (3) , 84
Open AccessDefects, Microstructure, and Hardness of As-Built and Heat-Treated 13 Hot Work Tool Steel and 17-4 PH Stainless Steel Obtained by Fused Filament Fabrication
Fused Filament Fabrication (FFF) is a low-cost additive manufacturing process that produces metallic parts from printing with a metal-polymer filament, followed by a debinding–sintering process. It presents an opportunity for the tooling sector to improve performance by geometrical optimization while keeping costs low. This study investigates the possibility of producing a molding core for plastic injection by FFF technology. This research aimed to characterize 17-4 PH stainless steel and H13 hot work tool steels produced through this process. Their heat treatment behavior was investigated using dilatometry, which led to the obtention of a Continuous Cooling Transformation (CCT) diagram. Results show that for as-sintered materials, martensitic steel with some residual austenite is present in 17-4 PH, and a pearlitic microstructure is observed in H13. Porosity (around 4%) falls within the reported range in the literature and can be removed by hot isostatic pressing. CCT diagrams do not show significant differences with conventional materials. The low hardness of as-sintered H13 (around 175 HV1) is improved (>500 HV1) by suitable heat treatment. Finally, both materials meet the requirements for this specific industrial application, and demonstrators were produced.
- 6 January 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (19) , 19541-19552
Impact of Heat Treatment on Hardness in Laser-Powder Bed Fusion (L-PBF) 17-4 PH Stainless Steel
- 6 January 2026
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 35 (19) , 19541-19552
Impact of Heat Treatment on Hardness in Laser-Powder Bed Fusion (L-PBF) 17-4 PH Stainless Steel
- Open Access
- 10 March 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (5) , 1690-1705
Near-Equilibrium Transformation Sequence of NiCrBSi Self-Fluxing Nickel Alloy
NiCrBSi alloys are widely used as wear-resistant deposits. However, despite several studies, there are still some remaining questions concerning their microstructure and the transformation sequence during solidification. This study investigates a gas-atomized powder's non-equilibrium microstructure and a cast sample's near-equilibrium microstructure by synchrotron XRD coupled with SEM observations. NiCrBSi alloys consist of a nickel-rich matrix with CrB, Cr7C3, Ni3B, Ni31Si12 crystals and γ′ Ni3Si β1 precipitates. The transformation sequence is studied by in situ XRD analyses using a synchrotron source. Melting and solidification of Ni31Si12 and Ni3B and solid-state transformations of Ni31Si12 and Ni3Si β1 are depicted. Finally, the nickel-rich γ (Ni) matrix, CrB and Cr7C3, are likely to remain solid at high temperatures up to 1200 °C.
- 10 March 2025
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 56 (5) , 1690-1705
Open AccessNear-Equilibrium Transformation Sequence of NiCrBSi Self-Fluxing Nickel Alloy
NiCrBSi alloys are widely used as wear-resistant deposits. However, despite several studies, there are still some remaining questions concerning their microstructure and the transformation sequence during solidification. This study investigates a gas-atomized powder's non-equilibrium microstructure and a cast sample's near-equilibrium microstructure by synchrotron XRD coupled with SEM observations. NiCrBSi alloys consist of a nickel-rich matrix with CrB, Cr7C3, Ni3B, Ni31Si12 crystals and γ′ Ni3Si β1 precipitates. The transformation sequence is studied by in situ XRD analyses using a synchrotron source. Melting and solidification of Ni31Si12 and Ni3B and solid-state transformations of Ni31Si12 and Ni3Si β1 are depicted. Finally, the nickel-rich γ (Ni) matrix, CrB and Cr7C3, are likely to remain solid at high temperatures up to 1200 °C.
- Open Access
Material Health of NiCrBSi Alloy Parts Produced via the Laser Powder Bed Fusion Process
Laser powder bed fusion (L-PBF) is a novel process representing a possible solution for producing resistant parts using NiCrBSi hard-facing nickel alloys with complex geometry. Process parameters for more common alloys are explored with a standard Renishaw AM400 device (Renishaw, Wotton-under-Edge, UK) and an SLM Solution 250 device (SLM Solutions Group AG, Lübeck, Germany) modified with a baseplate preheated at high temperatures (300 °C and 500 °C). Laser remelting is also investigated in hopes of further improving material health. The origin of the main defects is studied. A lack of fusion is likely to be generated by spatters ejected from the melting pool while cracks are induced by the alloy’s lack of toughness. Using image analyses, those defects are quantified and correlated with processing parameters. Lack of fusion and total crack length decrease with an increase in baseplate’s preheating temperature. However, crack width increases with preheating temperature. Therefore, via a careful optimization of process parameters, samples with a surface density of 99% and narrow cracks are obtained.
Open AccessMaterial Health of NiCrBSi Alloy Parts Produced via the Laser Powder Bed Fusion Process
Laser powder bed fusion (L-PBF) is a novel process representing a possible solution for producing resistant parts using NiCrBSi hard-facing nickel alloys with complex geometry. Process parameters for more common alloys are explored with a standard Renishaw AM400 device (Renishaw, Wotton-under-Edge, UK) and an SLM Solution 250 device (SLM Solutions Group AG, Lübeck, Germany) modified with a baseplate preheated at high temperatures (300 °C and 500 °C). Laser remelting is also investigated in hopes of further improving material health. The origin of the main defects is studied. A lack of fusion is likely to be generated by spatters ejected from the melting pool while cracks are induced by the alloy’s lack of toughness. Using image analyses, those defects are quantified and correlated with processing parameters. Lack of fusion and total crack length decrease with an increase in baseplate’s preheating temperature. However, crack width increases with preheating temperature. Therefore, via a careful optimization of process parameters, samples with a surface density of 99% and narrow cracks are obtained.
- Open Access
- 12 July 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 25, 6644-6659
Performance evaluation of Charpy impact tests to investigate and detect process defects of a Ni-based superalloy elaborated by laser powder bed fusion
- 12 July 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 25, 6644-6659
Open AccessPerformance evaluation of Charpy impact tests to investigate and detect process defects of a Ni-based superalloy elaborated by laser powder bed fusion
- Open Access
- 14 December 2021
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 5 (4) , 136
Laser Welding of AISI 316L Stainless Steel Produced by Additive Manufacturing or by Conventional Processes
Among all the additive manufacturing techniques, Laser Powder Bed Fusion (LBPF), also called Selective Laser Melting (SLM), is the most common technique due to its high capability of building complex parts with generally improved mechanical properties. One of the main drawbacks of this technique is the sample size limitation, which depends on elaborating chamber dimensions. In this study, we investigate the viability of obtaining large parts with the laser welding of additive manufactured plates. A comparison of the microstructure and the tensile mechanical properties of SLM-welded plates and cold-rolled welded plates was performed. This paper shows the possibility of obtaining defect-free parts. Even if welding has a low impact on the microstructure of the SLM samples, fractures are located on the fusion zone, and a decrease in ductility of around 30% compared to the base metal is observed.
- 14 December 2021
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 5 (4) , 136
Open AccessLaser Welding of AISI 316L Stainless Steel Produced by Additive Manufacturing or by Conventional Processes
Among all the additive manufacturing techniques, Laser Powder Bed Fusion (LBPF), also called Selective Laser Melting (SLM), is the most common technique due to its high capability of building complex parts with generally improved mechanical properties. One of the main drawbacks of this technique is the sample size limitation, which depends on elaborating chamber dimensions. In this study, we investigate the viability of obtaining large parts with the laser welding of additive manufactured plates. A comparison of the microstructure and the tensile mechanical properties of SLM-welded plates and cold-rolled welded plates was performed. This paper shows the possibility of obtaining defect-free parts. Even if welding has a low impact on the microstructure of the SLM samples, fractures are located on the fusion zone, and a decrease in ductility of around 30% compared to the base metal is observed.
- 1 August 2021
- Published by Elsevier in Materialia
- Vol. 18
In situ observation of liquid metal dealloying and etching of porous FeCr by X-ray tomography and X-ray diffraction
- 1 August 2021
- Published by Elsevier in Materialia
- Vol. 18
In situ observation of liquid metal dealloying and etching of porous FeCr by X-ray tomography and X-ray diffraction
- 3 July 2020
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (12)
Mechanical Properties of FeCr‐Based Composite Materials Elaborated by Liquid Metal Dealloying towards Bioapplication
Liquid metal dealloying (LMD) is a new technology to create porous materials. From a (FeCr)x‐Ni1–x precursor, it is possible to get a bicontinuous structure of FeCr and Mg: a metal–metal composite. An etching step removes the Mg solid‐state solution phase to give a metal–air composite. The last step, polymer infiltration, gives metal–polymer composites. Herein, metal–metal, metal–air, and metal–polymer (rubbery or glassy polymers) with three different phase ratios are elaborated by LMD from Ni‐based precursors and their mechanical properties are analyzed. A full polymer infiltration into the pores is obtained and the epoxy polymer properties are not affected by the metallic foam presence. Concerning control of the mechanical properties, the material's second‐phase selection is a key factor. Herein, it is shown that the mechanical properties are easily designed by optimizing phase ratio, ligament size, and second‐phase type and that these materials are promising materials for biomedical applications.
- 3 July 2020
- Published by Wiley in Advanced Engineering Materials
- Vol. 22 (12)
Mechanical Properties of FeCr‐Based Composite Materials Elaborated by Liquid Metal Dealloying towards Bioapplication
Liquid metal dealloying (LMD) is a new technology to create porous materials. From a (FeCr)x‐Ni1–x precursor, it is possible to get a bicontinuous structure of FeCr and Mg: a metal–metal composite. An etching step removes the Mg solid‐state solution phase to give a metal–air composite. The last step, polymer infiltration, gives metal–polymer composites. Herein, metal–metal, metal–air, and metal–polymer (rubbery or glassy polymers) with three different phase ratios are elaborated by LMD from Ni‐based precursors and their mechanical properties are analyzed. A full polymer infiltration into the pores is obtained and the epoxy polymer properties are not affected by the metallic foam presence. Concerning control of the mechanical properties, the material's second‐phase selection is a key factor. Herein, it is shown that the mechanical properties are easily designed by optimizing phase ratio, ligament size, and second‐phase type and that these materials are promising materials for biomedical applications.