Kean Boon Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Kean Boon Lee has a total of 103 co-authors. Here are the top co-authors by number of shared publications:
Joseph Pinchbeck
Department of Electronic and Electrical Engineering, The University of Sheffield, Sheffield, U.K.
3 shared publications- Michael J. Uren
H. H. Wills Physics Laboratory, Center for Device Thermography and Reliability, University of Bristol, Bristol, U.K.
3 shared publications Sheng Jiang
The University of Sheffield, Sheffield, Sheffield, UNITED KINGDOM OF GREAT BRITAIN AND NORTHERN IRELAND
3 shared publicationsF. Ranalli
University of Sheffield 1 Department of Electronic and Electrical Engineering Sheffield S1 3JD, United Kingdom
2 shared publications- Jie Bai
Department of Electronic and Electrical Engineering, The University of Sheffield, Sheffield S1 3JD, United Kingdom
2 shared publications - Martin Kuball
University of Bristol
2 shared publications
Latest Publications
- 1 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (10) , 1641-1644
Fabrication of Semi-Polar (11-22) GaN V-Groove MOSFET Using Wet Etching Trench Opening Technique
In this letter, we report the fabrication of an enhancement-mode V-groove metal oxide semiconductor field-effect transistor on semi-polar (11-22) GaN platform. A wet crystallographic hydroxide-based etching approach to achieve a vertical inversion trench sidewall is utilized. This novel fabrication method enables the formation of the vertical trench sidewall channel conduction without the need for a conventional chlorine-based dry etching. The fabricated VMOSFET exhibit a threshold voltage of 9.49 V, a current ON/OFF ratio of >107, an ON-state resistance of 8.0 $\text{m}\Omega $ .cm2, and an output current of 516 A/cm2.
- 1 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (10) , 1641-1644
Fabrication of Semi-Polar (11-22) GaN V-Groove MOSFET Using Wet Etching Trench Opening Technique
In this letter, we report the fabrication of an enhancement-mode V-groove metal oxide semiconductor field-effect transistor on semi-polar (11-22) GaN platform. A wet crystallographic hydroxide-based etching approach to achieve a vertical inversion trench sidewall is utilized. This novel fabrication method enables the formation of the vertical trench sidewall channel conduction without the need for a conventional chlorine-based dry etching. The fabricated VMOSFET exhibit a threshold voltage of 9.49 V, a current ON/OFF ratio of >107, an ON-state resistance of 8.0 $\text{m}\Omega $ .cm2, and an output current of 516 A/cm2.
- 16 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (4) , 533-536
High-Performance Enhancement-Mode p-Channel GaN MISFETs With Steep Subthreshold Swing
We report an enhancement-mode (E-mode)${p}$ -channel GaN heterojunction field-effect transistor with a metal-insulator-semiconductor gate structure. A 60 mV/dec subthreshold swing is experimentally achieved in the E-mode GaN${p}$ -channel transistors on an unintentionally doped GaN interlayer for the first time by using a low-power plasma gate recessing etch and gate dielectric deposition pre-treatment. The fabricated${p}$ -channel transistors exhibit excellent E-mode performance with a threshold voltage of −1.53 V, an effective on-resistance of 1.0$\text{k}\Omega $ .mm, a peak transconductance of 1.0 mS/mm, and a high$\text{I}_{ \mathrm{\scriptscriptstyle ON}}/\text{I}_{ \mathrm{\scriptscriptstyle OFF}}$ ratio > 10 7 . Bi-directional gate sweep measurements on the p-channel devices show a threshold voltage shift of 0.12 V and an increased subthreshold swing of 107 mV/dec. In addition, the dual-channel conduction mechanism in the${p}$ -channel GaN transistors is presented and discussed.- 16 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (4) , 533-536
High-Performance Enhancement-Mode p-Channel GaN MISFETs With Steep Subthreshold Swing
We report an enhancement-mode (E-mode)${p}$ -channel GaN heterojunction field-effect transistor with a metal-insulator-semiconductor gate structure. A 60 mV/dec subthreshold swing is experimentally achieved in the E-mode GaN${p}$ -channel transistors on an unintentionally doped GaN interlayer for the first time by using a low-power plasma gate recessing etch and gate dielectric deposition pre-treatment. The fabricated${p}$ -channel transistors exhibit excellent E-mode performance with a threshold voltage of −1.53 V, an effective on-resistance of 1.0$\text{k}\Omega $ .mm, a peak transconductance of 1.0 mS/mm, and a high$\text{I}_{ \mathrm{\scriptscriptstyle ON}}/\text{I}_{ \mathrm{\scriptscriptstyle OFF}}$ ratio > 10 7 . Bi-directional gate sweep measurements on the p-channel devices show a threshold voltage shift of 0.12 V and an increased subthreshold swing of 107 mV/dec. In addition, the dual-channel conduction mechanism in the${p}$ -channel GaN transistors is presented and discussed.- 13 December 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (24) , 243502
Vertical field inhomogeneity associated with threading dislocations in GaN high electron mobility transistor epitaxial stacks
A measurement technique combining Kelvin-probe force microscopy with substrate bias is developed and demonstrated on AlGaN/GaN-on-Si device structures under conditions relevant to the effect of off-state drain bias stress in transistors. For a high substrate bias, the measurements show a significantly lowered surface potential surrounding a small proportion of dislocations imaged with atomic force microscopy (AFM), laterally extending on a scale of up to a micrometer. Both the density and the size of those features increase with substrate bias; however, conductive AFM measurements under the same bias conditions showed no leakage reaching the surface associated with those features. Our model considers localized conductive paths that end a certain distance below the 2D electron gas electrically “thinning” the epitaxy and, therefore, deforming the potential and increasing the electric field under off-state stress bias. The conclusion is that the vertical electric field in the buffer is laterally highly non-uniform with an enhanced vertical field in the vicinity of those dislocations. This non-uniformity redirects the substrate bias stress from the buffer to the channel with potential consequences for breakdown.
- 13 December 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (24) , 243502
Vertical field inhomogeneity associated with threading dislocations in GaN high electron mobility transistor epitaxial stacks
A measurement technique combining Kelvin-probe force microscopy with substrate bias is developed and demonstrated on AlGaN/GaN-on-Si device structures under conditions relevant to the effect of off-state drain bias stress in transistors. For a high substrate bias, the measurements show a significantly lowered surface potential surrounding a small proportion of dislocations imaged with atomic force microscopy (AFM), laterally extending on a scale of up to a micrometer. Both the density and the size of those features increase with substrate bias; however, conductive AFM measurements under the same bias conditions showed no leakage reaching the surface associated with those features. Our model considers localized conductive paths that end a certain distance below the 2D electron gas electrically “thinning” the epitaxy and, therefore, deforming the potential and increasing the electric field under off-state stress bias. The conclusion is that the vertical electric field in the buffer is laterally highly non-uniform with an enhanced vertical field in the vicinity of those dislocations. This non-uniformity redirects the substrate bias stress from the buffer to the channel with potential consequences for breakdown.
- Open Access
- 22 December 2020
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (10) , 105104
Dual metal gate AlGaN/GaN high electron mobility transistors with improved transconductance and reduced short channel effects
AlGaN/GaN high electron mobility transistors with a range of dual metal gate (DMG) lengths have been fabricated and studied. An improvement in transconductance up to 9% has been measured in the DMG devices in comparison to the conventional single metal gate devices. This is attributed to the distribution of the electric field under the gate region as a result of two gate metals. The drain induced barrier lowering is also suppressed using the sub-µm DMG devices, with a drain induced barrier lowering decrease of around 50% due to a potential shielding effect in the two-dimensional electron gas channel.
- 22 December 2020
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (10) , 105104
Open AccessDual metal gate AlGaN/GaN high electron mobility transistors with improved transconductance and reduced short channel effects
AlGaN/GaN high electron mobility transistors with a range of dual metal gate (DMG) lengths have been fabricated and studied. An improvement in transconductance up to 9% has been measured in the DMG devices in comparison to the conventional single metal gate devices. This is attributed to the distribution of the electric field under the gate region as a result of two gate metals. The drain induced barrier lowering is also suppressed using the sub-µm DMG devices, with a drain induced barrier lowering decrease of around 50% due to a potential shielding effect in the two-dimensional electron gas channel.
- 11 February 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (7)
A 624 V 5 A All‐GaN Integrated Cascode for Power‐Switching Applications
An all‐GaN integrated cascode device with an output current of 5 A, threshold voltage of +0.65 V and breakdown voltage of 624 V is demonstrated. Compared with the commercial 600 V hybrid GaN plus Si cascode device (TPH3202), the integrated cascode exhibits a significantly reduced delay time when switched at 200 V and 2.7 A. This is attributed to the absence of a Si metal–oxide–semiconductor field‐effect transistor (MOSFET) driver, leading to a much smaller input capacitance as indicated by the high voltage capacitance measurements. In addition, the integrated cascode device shows a reduced ringing effect due to monolithic integration. When compared with commercial 600 V standalone GaN devices (GS66502B and GS‐065‐004), a reduced Miller effect is observed for the integrated cascode when switched under low gate‐driving current conditions. The results demonstrate the advantages of the cascode device to switch with low gate‐driving current using cheaper, faster, and more efficient gate drivers.
- 11 February 2020
- Published by Wiley in Physica Status Solidi (a)
- Vol. 217 (7)
A 624 V 5 A All‐GaN Integrated Cascode for Power‐Switching Applications
An all‐GaN integrated cascode device with an output current of 5 A, threshold voltage of +0.65 V and breakdown voltage of 624 V is demonstrated. Compared with the commercial 600 V hybrid GaN plus Si cascode device (TPH3202), the integrated cascode exhibits a significantly reduced delay time when switched at 200 V and 2.7 A. This is attributed to the absence of a Si metal–oxide–semiconductor field‐effect transistor (MOSFET) driver, leading to a much smaller input capacitance as indicated by the high voltage capacitance measurements. In addition, the integrated cascode device shows a reduced ringing effect due to monolithic integration. When compared with commercial 600 V standalone GaN devices (GS66502B and GS‐065‐004), a reduced Miller effect is observed for the integrated cascode when switched under low gate‐driving current conditions. The results demonstrate the advantages of the cascode device to switch with low gate‐driving current using cheaper, faster, and more efficient gate drivers.
- 31 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (7) , 2495-2504
Analysis of Gain Variation With Changing Supply Voltages in GaN HEMTs for Envelope Tracking Power Amplifiers
Envelope tracking (ET) is a promising power amplifier (PA) architecture for current and future communications systems, which uses dynamic modulation of the supply voltage to provide high efficiency and potentially very wide bandwidth over a large dynamic range of output power. However, the dynamic nature of the supply voltage can lead to a problematic variation in transistor gain, particularly in GaN HEMTs. This paper describes and analyzes this behavior and the detrimental effect it can have on ET PAs. Contributing factors and origins of gain variation are described in detail along with how, for the first time, meaningful comparisons can be made between different devices. Using these guidelines, gain variation is shown to be a widespread issue effecting most GaN HEMTs presented in literature. To allow an analysis of the intrinsic device behavior, an extended transistor model is developed that takes the effect of gate and source field plates into account. This model is refined using measurement data and used to demonstrate the fact that the parasitic gate-drain capacitance (C GD ) is the main contributor to the small-signal gain variation-a significant part of the overall gain variation. Based on this knowledge, possible strategies to reduce gain variation at the transistor technology level are proposed, allowing the optimization of GaN HEMTs specifically for ET PAs. One identified strategy involves reducing the length of the gate field plate and is shown to be a viable approach to reduce the gain variation in GaN HEMTs, albeit at an increased RF/dc dispersion.
- 31 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 67 (7) , 2495-2504
Analysis of Gain Variation With Changing Supply Voltages in GaN HEMTs for Envelope Tracking Power Amplifiers
Envelope tracking (ET) is a promising power amplifier (PA) architecture for current and future communications systems, which uses dynamic modulation of the supply voltage to provide high efficiency and potentially very wide bandwidth over a large dynamic range of output power. However, the dynamic nature of the supply voltage can lead to a problematic variation in transistor gain, particularly in GaN HEMTs. This paper describes and analyzes this behavior and the detrimental effect it can have on ET PAs. Contributing factors and origins of gain variation are described in detail along with how, for the first time, meaningful comparisons can be made between different devices. Using these guidelines, gain variation is shown to be a widespread issue effecting most GaN HEMTs presented in literature. To allow an analysis of the intrinsic device behavior, an extended transistor model is developed that takes the effect of gate and source field plates into account. This model is refined using measurement data and used to demonstrate the fact that the parasitic gate-drain capacitance (C GD ) is the main contributor to the small-signal gain variation-a significant part of the overall gain variation. Based on this knowledge, possible strategies to reduce gain variation at the transistor technology level are proposed, allowing the optimization of GaN HEMTs specifically for ET PAs. One identified strategy involves reducing the length of the gate field plate and is shown to be a viable approach to reduce the gain variation in GaN HEMTs, albeit at an increased RF/dc dispersion.
- Open Access
- 29 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (5) , 1-7
Controllable Uniform Green Light Emitters Enabled by Circular HEMT-LED Devices
This paper reports a monolithic integration of GaN high-electron-mobility transistor (HEMT) and green light-emitting diode (LED), where the circular HEMT is surrounded by a ring-shaped LED and two devices are seamlessly interconnected by the LED's n-GaN layer and the HEMT's two-dimensional electron gas (2DEG) channel. By adopting such a novel circular layout design, the green HEMT-LED shows a controllable and uniform green light emission at 507 nm by simply tuning its gate voltage. This enables a uniform, controllable green LED light source, serving as an essential element in the red-green-blue (RGB) LED solution for a wide range of applications, such as tunable-spectrum white LED illumination, multichannel visible light communication with wavelength division multiplexing, RGB-based full-color LED displays, and optogenetics.
- 29 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (5) , 1-7
Open AccessControllable Uniform Green Light Emitters Enabled by Circular HEMT-LED Devices
This paper reports a monolithic integration of GaN high-electron-mobility transistor (HEMT) and green light-emitting diode (LED), where the circular HEMT is surrounded by a ring-shaped LED and two devices are seamlessly interconnected by the LED's n-GaN layer and the HEMT's two-dimensional electron gas (2DEG) channel. By adopting such a novel circular layout design, the green HEMT-LED shows a controllable and uniform green light emission at 507 nm by simply tuning its gate voltage. This enables a uniform, controllable green LED light source, serving as an essential element in the red-green-blue (RGB) LED solution for a wide range of applications, such as tunable-spectrum white LED illumination, multichannel visible light communication with wavelength division multiplexing, RGB-based full-color LED displays, and optogenetics.
- Open Access
- 26 March 2018
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 51 (16) , 163001
The 2018 GaN power electronics roadmap
- 26 March 2018
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 51 (16) , 163001
Open AccessThe 2018 GaN power electronics roadmap
- 1 January 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2003 (21593523) , 115-118
The temperature dependent TCAD and SPICE modeling of AlGaN/GaN HEMTs
In this work, the temperature dependent TCAD and SPICE modeling platform of AlGaN/GaN HEMTs has been established by using Sentaurus TCAD and Silvaco UTMOST IV. Typically, the temperature co-efficient of series resistance, trans-conductance, sub-threshold swing and gate/buffer leakage has been extracted from the TCAD simulation. Based on that, the compact SPICE device model of HEMTs has been built up, which can be used for DC/transient SPICE simulation and power electronics circuit demonstration. The SPICE modeling results agree well with our TCAD simulation, indicating good revealing of the physical mechanisms of the AlGaN/GaN HEMTs' operation.
- 1 January 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2003 (21593523) , 115-118
The temperature dependent TCAD and SPICE modeling of AlGaN/GaN HEMTs
In this work, the temperature dependent TCAD and SPICE modeling platform of AlGaN/GaN HEMTs has been established by using Sentaurus TCAD and Silvaco UTMOST IV. Typically, the temperature co-efficient of series resistance, trans-conductance, sub-threshold swing and gate/buffer leakage has been extracted from the TCAD simulation. Based on that, the compact SPICE device model of HEMTs has been built up, which can be used for DC/transient SPICE simulation and power electronics circuit demonstration. The SPICE modeling results agree well with our TCAD simulation, indicating good revealing of the physical mechanisms of the AlGaN/GaN HEMTs' operation.
- 1 July 2010
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 108 (1) , 013711
Characterization of gate recessed GaN/AlGaN/GaN high electron mobility transistors fabricated using a SiCl4/SF6 dry etch recipe
Incorporating GaN capping layers in conjunction with recessing has been identified as a means to maximize the high frequency performance of AlGaN/GaN high electron mobility transistors (HEMTs). Doping the cap heavily n-type is required in order to ensure minimal loss of carriers from the channel. Using a dry etch plasma recipe, 250 nm gate length HEMTs with recess lengths varying from 300 nm to are fabricated. Heavily doped caps enabled contact resistances of to be achieved. Recessing using a recipe does not introduce significant numbers of bulk traps. Gate recessing in conjunction with passivation reduces rf dispersion to negligible levels.- 1 July 2010
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 108 (1) , 013711
Characterization of gate recessed GaN/AlGaN/GaN high electron mobility transistors fabricated using a SiCl4/SF6 dry etch recipe
Incorporating GaN capping layers in conjunction with recessing has been identified as a means to maximize the high frequency performance of AlGaN/GaN high electron mobility transistors (HEMTs). Doping the cap heavily n-type is required in order to ensure minimal loss of carriers from the channel. Using a dry etch plasma recipe, 250 nm gate length HEMTs with recess lengths varying from 300 nm to are fabricated. Heavily doped caps enabled contact resistances of to be achieved. Recessing using a recipe does not introduce significant numbers of bulk traps. Gate recessing in conjunction with passivation reduces rf dispersion to negligible levels.