Alison M. Engwall
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alison M. Engwall has a total of 117 co-authors. Here are the top co-authors by number of shared publications:
- Seok Joon Shin
Lawrence Livermore National Laboratory
14 shared publications - Leonardus Bimo Bayu Aji
Lawrence Livermore National Laboratory , Livermore, California 94550
11 shared publications - John H. Bae
General Atomics 2 , San Diego, California 92186
9 shared publications - Alexander A. Baker
Materials Science Division, Lawrence Livermore National Laboratory, Livermore, CA 94550, USA
8 shared publications S. O. Kucheyev
Lawrence Livermore National Laboratory 1 , Livermore, California 94550
8 shared publications- John D. Moody
Lawrence Livermore National Laboratory , Livermore, California 94550
7 shared publications
Latest Publications
- Open Access
- 30 May 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (4)
Boron carbide films with reduced nodular defect density deposited by full-face erosion radio-frequency magnetron sputtering
Boron carbide coatings deposited by sputtering with conventional planar magnetrons exhibit nodular growth defects. Here, we demonstrate that the density of nodular defects in B4C films can be greatly reduced by using a full-face-erosion magnetron source that achieves a more uniform target erosion by sweeping the confining magnetic field over the target surface. We systematically study properties of B4C films deposited on substrates with different tilt angles and demonstrate deposition of ultrathick films with compressive residual stress below 200 MPa.
- 30 May 2024
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 42 (4)
Open AccessBoron carbide films with reduced nodular defect density deposited by full-face erosion radio-frequency magnetron sputtering
Boron carbide coatings deposited by sputtering with conventional planar magnetrons exhibit nodular growth defects. Here, we demonstrate that the density of nodular defects in B4C films can be greatly reduced by using a full-face-erosion magnetron source that achieves a more uniform target erosion by sweeping the confining magnetic field over the target surface. We systematically study properties of B4C films deposited on substrates with different tilt angles and demonstrate deposition of ultrathick films with compressive residual stress below 200 MPa.
- Open Access
- 28 February 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (8)
Magnetron sputter deposition of boron carbide in Ne and Ar plasmas
Conventional magnetron sputter deposition of B4C uses Ar as the working gas. Here, we explore the magnetron sputter deposition of B4C with a Ne plasma, which is expected to exhibit larger sputtering yields than Ar. We study properties of films deposited with different substrate tilt angles with the magnetron source operated in either direct-current (DC) or radio-frequency (RF) mode in an Ar or Ne plasma. Results show that the B4C film properties are determined by a combination of sputtering ballistics and effects of the working gas on the plasma discharge and gas phase scattering of depositing species flux. At constant discharge power, deposition rates for Ar and Ne plasmas are similar, which is attributed to balancing effects of a higher ballistic sputtering yield of Ne and lower ion flux to the target. Both depositing B and C neutral species and bombarding ions have higher energies for the case of Ne plasmas. Films deposited with the RF-driven Ne plasma exhibit a uniform non-columnar structure, lowest oxygen impurity content, and highest mass density and mechanical properties at a cost of Ne incorporation and larger compressive residual stress.
- 28 February 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (8)
Open AccessMagnetron sputter deposition of boron carbide in Ne and Ar plasmas
Conventional magnetron sputter deposition of B4C uses Ar as the working gas. Here, we explore the magnetron sputter deposition of B4C with a Ne plasma, which is expected to exhibit larger sputtering yields than Ar. We study properties of films deposited with different substrate tilt angles with the magnetron source operated in either direct-current (DC) or radio-frequency (RF) mode in an Ar or Ne plasma. Results show that the B4C film properties are determined by a combination of sputtering ballistics and effects of the working gas on the plasma discharge and gas phase scattering of depositing species flux. At constant discharge power, deposition rates for Ar and Ne plasmas are similar, which is attributed to balancing effects of a higher ballistic sputtering yield of Ne and lower ion flux to the target. Both depositing B and C neutral species and bombarding ions have higher energies for the case of Ne plasmas. Films deposited with the RF-driven Ne plasma exhibit a uniform non-columnar structure, lowest oxygen impurity content, and highest mass density and mechanical properties at a cost of Ne incorporation and larger compressive residual stress.
- Open Access
- 17 January 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (3)
Deposition of ultrathick heavy-metal alloys on rotating substrates by high-power impulse magnetron sputtering: Target erosion effects
Sputter deposition of ultrathick (≈20μm) Au–Ta alloy coatings on sphero-cylindrical substrates is key for the fabrication of hohlraums for magnetically assisted inertial confinement fusion. Here, we study the deposition of AuTa4 alloy coatings onto rotating substrates. We use high-power impulse magnetron sputtering (HiPIMS) in a constant peak target voltage mode. Results show that the target erosion state has a strong impact on the dominant crystallographic phase, microstructure, surface morphology, and electrical resistivity of AuTa4 films. This is due to effects of changes in the confining magnetic field with target erosion on the HiPIMS discharge characteristics and the sputter source output. We quantify these effects via plasma diagnostics and discuss the optimization of HiPIMS deposition of ultrathick films for cases when target erosion effects dominate film properties.
- 17 January 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (3)
Open AccessDeposition of ultrathick heavy-metal alloys on rotating substrates by high-power impulse magnetron sputtering: Target erosion effects
Sputter deposition of ultrathick (≈20μm) Au–Ta alloy coatings on sphero-cylindrical substrates is key for the fabrication of hohlraums for magnetically assisted inertial confinement fusion. Here, we study the deposition of AuTa4 alloy coatings onto rotating substrates. We use high-power impulse magnetron sputtering (HiPIMS) in a constant peak target voltage mode. Results show that the target erosion state has a strong impact on the dominant crystallographic phase, microstructure, surface morphology, and electrical resistivity of AuTa4 films. This is due to effects of changes in the confining magnetic field with target erosion on the HiPIMS discharge characteristics and the sputter source output. We quantify these effects via plasma diagnostics and discuss the optimization of HiPIMS deposition of ultrathick films for cases when target erosion effects dominate film properties.
- Open Access
- 1 July 2023
- Published by AIP Publishing in Physics of Plasmas
- Vol. 30 (7)
Performance scaling with an applied magnetic field in indirect-drive inertial confinement fusion implosions
Magnetizing a cryogenic deuterium–tritium (DT)-layered inertial confinement fusion (ICF) implosion can improve performance by reducing thermal conduction and improving DT-alpha confinement in the hot spot. A room-temperature, magnetized indirect-drive ICF platform at the National Ignition Facility has been developed, using a high-Z, high-resistivity AuTa4 alloy as the hohlraum wall material. Experiments show a 2.5× increase in deuterium–deuterium (DD) neutron yield and a 0.8-keV increase in hot-spot temperature with the application of a 12-T B-field. For an initial 26-T B-field, we observed a 2.9× yield increase and a 1.1-keV temperature increase, with the inferred burn-averaged B-field in the compressed hot spot estimated to be 7.1 ± 1.8 kT using measured primary DD-n and secondary DT-n neutron yields.
- 1 July 2023
- Published by AIP Publishing in Physics of Plasmas
- Vol. 30 (7)
Open AccessPerformance scaling with an applied magnetic field in indirect-drive inertial confinement fusion implosions
Magnetizing a cryogenic deuterium–tritium (DT)-layered inertial confinement fusion (ICF) implosion can improve performance by reducing thermal conduction and improving DT-alpha confinement in the hot spot. A room-temperature, magnetized indirect-drive ICF platform at the National Ignition Facility has been developed, using a high-Z, high-resistivity AuTa4 alloy as the hohlraum wall material. Experiments show a 2.5× increase in deuterium–deuterium (DD) neutron yield and a 0.8-keV increase in hot-spot temperature with the application of a 12-T B-field. For an initial 26-T B-field, we observed a 2.9× yield increase and a 1.1-keV temperature increase, with the inferred burn-averaged B-field in the compressed hot spot estimated to be 7.1 ± 1.8 kT using measured primary DD-n and secondary DT-n neutron yields.
- Open Access
- 23 February 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (2)
Radio-frequency magnetron sputter deposition of ultrathick boron carbide films
The deposition of thick B4C films with low residual stress by conventional direct-current magnetron sputtering is accompanied by the formation of dust particulates contaminating the target, chamber, and substrates and leading to the formation of nodular defects in films. Here, we demonstrate that the formation of particulates is greatly reduced during radio-frequency magnetron sputtering (RFMS). We systematically study properties of B4C films deposited by RFMS with a substrate temperature of 330 °C, a target-to-substrate distance of 10 cm, Ar working gas pressure in the range of 4.5–12.0 mTorr (0.6–1.6 Pa), and substrate tilt angles of 0°–80°. All films are x-ray amorphous. A columnar structure develops with increasing either Ar pressure or substrate tilt. For columnar films, the column tilt angle decreases with increasing Ar pressure, which we attribute to a corresponding increase in the width of the distribution of impact angles of deposition flux. In contrast to the Keller–Simmons rule, the deposition rate increases with increasing Ar pressure, which suggests a better coupling of the RF energy to the plasma processes that lead to target sputtering at higher pressures. There is a critical substrate tilt angle above which the total residual stress is close to zero. This critical substrate tilt angle is ∼0° for an Ar pressure of 12 mTorr (1.6 Pa). The lower residual stress state, necessary for depositing ultrathick films, is characterized by a larger concentration of nanoscale inhomogeneities and decreased mechanical properties. Based on these results, RFMS deposition of 60-μm-thick B4C films is demonstrated.
- 23 February 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 41 (2)
Open AccessRadio-frequency magnetron sputter deposition of ultrathick boron carbide films
The deposition of thick B4C films with low residual stress by conventional direct-current magnetron sputtering is accompanied by the formation of dust particulates contaminating the target, chamber, and substrates and leading to the formation of nodular defects in films. Here, we demonstrate that the formation of particulates is greatly reduced during radio-frequency magnetron sputtering (RFMS). We systematically study properties of B4C films deposited by RFMS with a substrate temperature of 330 °C, a target-to-substrate distance of 10 cm, Ar working gas pressure in the range of 4.5–12.0 mTorr (0.6–1.6 Pa), and substrate tilt angles of 0°–80°. All films are x-ray amorphous. A columnar structure develops with increasing either Ar pressure or substrate tilt. For columnar films, the column tilt angle decreases with increasing Ar pressure, which we attribute to a corresponding increase in the width of the distribution of impact angles of deposition flux. In contrast to the Keller–Simmons rule, the deposition rate increases with increasing Ar pressure, which suggests a better coupling of the RF energy to the plasma processes that lead to target sputtering at higher pressures. There is a critical substrate tilt angle above which the total residual stress is close to zero. This critical substrate tilt angle is ∼0° for an Ar pressure of 12 mTorr (1.6 Pa). The lower residual stress state, necessary for depositing ultrathick films, is characterized by a larger concentration of nanoscale inhomogeneities and decreased mechanical properties. Based on these results, RFMS deposition of 60-μm-thick B4C films is demonstrated.
- 10 October 2022
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 55 (48) , 485302
Combinatorial sputter deposition of ultrathick Au-Bi alloy films
Gold-bismuth alloys are of interest as catalysts and catalytic sensing systems, electrochemical sensors, superconductors, and hohlraums for magnetically assisted inertial confinement fusion implosions. Radiation-hydrodynamics simulations with the Lasnex code of laser-driven hohlraums predict higher x-ray drive from Au-Bi alloys compared with cases of Au-Ta or pure Au and Bi hohlraums. Here, we use direct current magnetron sputtering in Ar gas, with co-sputtering from two elemental targets, to deposit Au-Bi alloys with Bi content of 9–77 at.% and thicknesses up to ∼20 µm. Films are characterized by a combination of x-ray diffraction, Rutherford backscattering, scanning electron microscopy, substrate-curvature-based residual stress, and electronic transport measurements. Experiments are complemented by Monte Carlo simulations of ballistic sputtering and gas phase transport of depositing species and Ar gas atoms. Results show that all films are polycrystalline, with three distinct compositional regimes dominated by Au, Au2Bi, and Bi crystallographic phases. A metallic behavior of the temperature dependence of electrical resistivity is observed for all the films. Films with Bi content above ∼30 at.% exhibit porosity, which is tolerable to hohlraum x-ray drive based on Lasnex simulations.
- 10 October 2022
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 55 (48) , 485302
Combinatorial sputter deposition of ultrathick Au-Bi alloy films
Gold-bismuth alloys are of interest as catalysts and catalytic sensing systems, electrochemical sensors, superconductors, and hohlraums for magnetically assisted inertial confinement fusion implosions. Radiation-hydrodynamics simulations with the Lasnex code of laser-driven hohlraums predict higher x-ray drive from Au-Bi alloys compared with cases of Au-Ta or pure Au and Bi hohlraums. Here, we use direct current magnetron sputtering in Ar gas, with co-sputtering from two elemental targets, to deposit Au-Bi alloys with Bi content of 9–77 at.% and thicknesses up to ∼20 µm. Films are characterized by a combination of x-ray diffraction, Rutherford backscattering, scanning electron microscopy, substrate-curvature-based residual stress, and electronic transport measurements. Experiments are complemented by Monte Carlo simulations of ballistic sputtering and gas phase transport of depositing species and Ar gas atoms. Results show that all films are polycrystalline, with three distinct compositional regimes dominated by Au, Au2Bi, and Bi crystallographic phases. A metallic behavior of the temperature dependence of electrical resistivity is observed for all the films. Films with Bi content above ∼30 at.% exhibit porosity, which is tolerable to hohlraum x-ray drive based on Lasnex simulations.
- 3 October 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (14)
Reactive co-sputtering of ternary Au–Ta–O films with tunable electrical resistivity
Heavy-metal-based films with high electrical resistivity are needed for hohlraums for magnetically assisted inertial confinement fusion. Here, we study ternary Au–Ta–O films deposited by reactive direct-current magnetron co-sputtering from elemental Au and Ta targets in an oxygen containing atmosphere. By varying the O content, the electrical resistivity of films can be tuned in a wide range of ∼100–40 000 μΩ cm. With increasing O content, a drastic increase in resistivity occurs at ∼45 at. % of O, separating regimes with two different dominant conduction mechanisms attributed to metallic conduction through the Au–Ta alloy matrix (for ≲45 at. % of O) and tunneling across insulating Ta2O5 layers separating conducting islands (for ≳45 at. % of O). Post-deposition annealing at 300 °C leads to the segregation of Au into ∼50-nm islands, sharply decreasing the resistivity for films with ≳45 at. % of O but not for the metal-like films with lower O content.
- 3 October 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (14)
Reactive co-sputtering of ternary Au–Ta–O films with tunable electrical resistivity
Heavy-metal-based films with high electrical resistivity are needed for hohlraums for magnetically assisted inertial confinement fusion. Here, we study ternary Au–Ta–O films deposited by reactive direct-current magnetron co-sputtering from elemental Au and Ta targets in an oxygen containing atmosphere. By varying the O content, the electrical resistivity of films can be tuned in a wide range of ∼100–40 000 μΩ cm. With increasing O content, a drastic increase in resistivity occurs at ∼45 at. % of O, separating regimes with two different dominant conduction mechanisms attributed to metallic conduction through the Au–Ta alloy matrix (for ≲45 at. % of O) and tunneling across insulating Ta2O5 layers separating conducting islands (for ≳45 at. % of O). Post-deposition annealing at 300 °C leads to the segregation of Au into ∼50-nm islands, sharply decreasing the resistivity for films with ≳45 at. % of O but not for the metal-like films with lower O content.
- 26 July 2022
- Published by Elsevier in Thin Solid Films
- Vol. 758
Sputter deposition of high electrical resistivity Au-Ta alloy coatings on rotating substrates
- 26 July 2022
- Published by Elsevier in Thin Solid Films
- Vol. 758
Sputter deposition of high electrical resistivity Au-Ta alloy coatings on rotating substrates
- Open Access
Tantalum Suboxide Films with Tunable Composition and Electrical Resistivity Deposited by Reactive Magnetron Sputtering
Tantalum-based films with tailored composition, density, and electrical resistivity are of interest for next generation hohlraums for magnetized indirect-drive inertial confinement fusion. Here, we use reactive direct-current magnetron sputtering to deposit tantalum suboxide films with O content in the range of 46–71 at.%. In contrast to a common approach involving varying reactive gas contents, compositional control is achieved kinetically by changing the total chamber pressure and the deposition rate, while keeping the working gas mix of Ar-5%O constant. The resultant films are X-ray amorphous with electrical resistivity varying by over seven orders of magnitude. The dominant conduction mechanism changes from metallic to activated tunneling above ∼55 at.% of O, which is characterized by a sharp increase in resistivity and a decrease in the carrier density at low temperatures.Open AccessTantalum Suboxide Films with Tunable Composition and Electrical Resistivity Deposited by Reactive Magnetron Sputtering
Tantalum-based films with tailored composition, density, and electrical resistivity are of interest for next generation hohlraums for magnetized indirect-drive inertial confinement fusion. Here, we use reactive direct-current magnetron sputtering to deposit tantalum suboxide films with O content in the range of 46–71 at.%. In contrast to a common approach involving varying reactive gas contents, compositional control is achieved kinetically by changing the total chamber pressure and the deposition rate, while keeping the working gas mix of Ar-5%O constant. The resultant films are X-ray amorphous with electrical resistivity varying by over seven orders of magnitude. The dominant conduction mechanism changes from metallic to activated tunneling above ∼55 at.% of O, which is characterized by a sharp increase in resistivity and a decrease in the carrier density at low temperatures. - 16 February 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (7) , 075304
Effect of substrate temperature on sputter-deposited boron carbide films
Sputter deposition of films with tailored physical properties remains a challenge. Here, we systematically study how substrate temperature influences the properties of films deposited by direct current magnetron sputtering onto planar substrates held at temperatures in the range of . Results show that all films are amorphous stoichiometric , with low O content of at. %. Films deposited onto substrates at exhibit high compressive residual stress and decreased mechanical properties. For elevated substrate temperatures in the range of , film mass density, surface roughness, Young’s modulus, and hardness are weakly dependent on substrate temperature. However, in this temperature range, an increase in substrate temperature leads to larger residual compressive stress accompanied by a corresponding reduction in the concentration of nanoscale inhomogeneities. At least for the landing atom ballistics conditions studied here, a substrate temperature range of is optimum for growing films with near-zero intrinsic residual stress. The overall weak substrate temperature dependence of film properties revealed in this work is favorable for the development of a robust deposition process, particularly for the case of deposition onto non-planar substrates where temperature control is often challenging.- 16 February 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (7) , 075304
Effect of substrate temperature on sputter-deposited boron carbide films
Sputter deposition of films with tailored physical properties remains a challenge. Here, we systematically study how substrate temperature influences the properties of films deposited by direct current magnetron sputtering onto planar substrates held at temperatures in the range of . Results show that all films are amorphous stoichiometric , with low O content of at. %. Films deposited onto substrates at exhibit high compressive residual stress and decreased mechanical properties. For elevated substrate temperatures in the range of , film mass density, surface roughness, Young’s modulus, and hardness are weakly dependent on substrate temperature. However, in this temperature range, an increase in substrate temperature leads to larger residual compressive stress accompanied by a corresponding reduction in the concentration of nanoscale inhomogeneities. At least for the landing atom ballistics conditions studied here, a substrate temperature range of is optimum for growing films with near-zero intrinsic residual stress. The overall weak substrate temperature dependence of film properties revealed in this work is favorable for the development of a robust deposition process, particularly for the case of deposition onto non-planar substrates where temperature control is often challenging.