Giovanni Lacagnina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Giovanni Lacagnina has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
Phillip Joseph
7 shared publicationsJung-Hoon Kim
4 shared publicationsMohammad Omidyeganeh
4 shared publicationsSeyed Mohammad Hasheminejad
Department of Mechanical, Aerospace and Civil Engineering, Brunel University, London UB8 3PH, United Kingdom
4 shared publicationsTze Pei Chong
Brunel University London, Uxbridge, England UB8 3PH, United Kingdom
4 shared publications- Tze Pei Chong
Department of Mechanical and Aerospace Engineering, Brunel University of London, Uxbridge UB8 3PH, UK
4 shared publications
Latest Publications
- 1 April 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 60 (4) , 2342-2353
Aerodynamic and Aeroacoustic Optimization of Leading-Edge Undulation of a NACA 65(12)-10 Airfoil
Experimental studies of a NACA 65(12)-10 airfoil with a sinusoidal leading-edge undulation (LEU) were carried out to simultaneously optimize its aerodynamic and aeroacoustic performances by conside...
- 1 April 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 60 (4) , 2342-2353
Aerodynamic and Aeroacoustic Optimization of Leading-Edge Undulation of a NACA 65(12)-10 Airfoil
Experimental studies of a NACA 65(12)-10 airfoil with a sinusoidal leading-edge undulation (LEU) were carried out to simultaneously optimize its aerodynamic and aeroacoustic performances by conside...
- Open Access
- 1 February 2021
- Published by SAGE Publications in International Journal of Aeroacoustics
- Vol. 20 (1-2) , 130-156
Leading edge serrations for the reduction of aerofoil self-noise at low angle of attack, pre-stall and post-stall conditions
This paper addresses the usefulness of leading edge serrations for reducing aerofoil self-noise over a wide range of angles of attack. Different serration geometries are studied over a range of Reynolds number . Design guidelines are proposed that permit noise reductions over most angles of attack. It is shown that serration geometries reduces the noise but adversely effect the aerodynamic performance suggesting that a trade-off should be sought between these two considerations. The self-noise performance of leading edge serrations has been shown to fall into three angle of attack (AoA) regimes: low angles where the flow is mostly attached, moderate angles where the flow is partially to fully separated, and high angles of attack where the flow is fully separated. Leading edge serrations have been demonstrated to be effective in reducing noise at low and high angles of attack but ineffective at moderate angles. The noise reduction mechanisms are explored in each of three angle regimes.- 1 February 2021
- Published by SAGE Publications in International Journal of Aeroacoustics
- Vol. 20 (1-2) , 130-156
Open AccessLeading edge serrations for the reduction of aerofoil self-noise at low angle of attack, pre-stall and post-stall conditions
This paper addresses the usefulness of leading edge serrations for reducing aerofoil self-noise over a wide range of angles of attack. Different serration geometries are studied over a range of Reynolds number . Design guidelines are proposed that permit noise reductions over most angles of attack. It is shown that serration geometries reduces the noise but adversely effect the aerodynamic performance suggesting that a trade-off should be sought between these two considerations. The self-noise performance of leading edge serrations has been shown to fall into three angle of attack (AoA) regimes: low angles where the flow is mostly attached, moderate angles where the flow is partially to fully separated, and high angles of attack where the flow is fully separated. Leading edge serrations have been demonstrated to be effective in reducing noise at low and high angles of attack but ineffective at moderate angles. The noise reduction mechanisms are explored in each of three angle regimes. - Open Access
- 1 June 2020
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 147 (6) , 3932-3947
On the manipulation of flow and acoustic fields of a blunt trailing edge aerofoil by serrated leading edges
This paper employs serrated leading edges to inject streamwise vorticity to the downstream boundary layer and wake to manipulate the flow field and noise sources near the blunt trailing edge of an asymmetric aerofoil. The use of a large serration amplitude is found to be effective to suppress the first noise source—bluntness-induced vortex shedding tonal noise—through the destruction of the coherent eigenmodes in the wake. The second noise source is the instability noise, which is produced by the interaction between the boundary layer instability and separation bubble near the blunt edge. The main criterion needed to suppress this noise source is related to a small serration wavelength because, through the generation of more streamwise vortices, it would facilitate a greater level of destructive interaction with the separation bubble. If the leading edge has both a large serration amplitude and wavelength, the interaction between the counter-rotating vortices themselves would trigger a turbulent shear layer through an inviscid mechanism. The turbulent shear layer will produce strong hydrodynamic pressure fluctuations to the trailing edge, which then scatter into broadband noise and transform into a trailing edge noise mechanism. This would become the third noise source that can be identified in several serrated leading edge configurations. Overall, a leading edge with a large serration amplitude and small serration wavelength appears to be the optimum choice to suppress the first and second noise sources and, at the same time, avoid the generation of the third noise source.
- 1 June 2020
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 147 (6) , 3932-3947
Open AccessOn the manipulation of flow and acoustic fields of a blunt trailing edge aerofoil by serrated leading edges
This paper employs serrated leading edges to inject streamwise vorticity to the downstream boundary layer and wake to manipulate the flow field and noise sources near the blunt trailing edge of an asymmetric aerofoil. The use of a large serration amplitude is found to be effective to suppress the first noise source—bluntness-induced vortex shedding tonal noise—through the destruction of the coherent eigenmodes in the wake. The second noise source is the instability noise, which is produced by the interaction between the boundary layer instability and separation bubble near the blunt edge. The main criterion needed to suppress this noise source is related to a small serration wavelength because, through the generation of more streamwise vortices, it would facilitate a greater level of destructive interaction with the separation bubble. If the leading edge has both a large serration amplitude and wavelength, the interaction between the counter-rotating vortices themselves would trigger a turbulent shear layer through an inviscid mechanism. The turbulent shear layer will produce strong hydrodynamic pressure fluctuations to the trailing edge, which then scatter into broadband noise and transform into a trailing edge noise mechanism. This would become the third noise source that can be identified in several serrated leading edge configurations. Overall, a leading edge with a large serration amplitude and small serration wavelength appears to be the optimum choice to suppress the first and second noise sources and, at the same time, avoid the generation of the third noise source.
- 6 December 2019
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 4 (12) , 123902
Mechanisms of airfoil noise near stall conditions
The focus of this paper is on investigating the noise produced by an airfoil at high angles of attack over a range of Reynolds number . The objective is not modeling this source of noise but rather understanding the mechanisms of generation for surface pressure fluctuations, due to a separated boundary layer, that are then scattered by the trailing edge. To this aim, we use simultaneous noise and surface pressure measurement in addition to velocimetric measurements by means of hot wire anemometry and time-resolved particle image velocimetry. Three possible mechanisms for the so-called “separation-stall noise” have been identified in addition to a clear link between far-field noise, surface pressure, and velocity fields in the noise generation.- 6 December 2019
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 4 (12) , 123902
Mechanisms of airfoil noise near stall conditions
The focus of this paper is on investigating the noise produced by an airfoil at high angles of attack over a range of Reynolds number . The objective is not modeling this source of noise but rather understanding the mechanisms of generation for surface pressure fluctuations, due to a separated boundary layer, that are then scattered by the trailing edge. To this aim, we use simultaneous noise and surface pressure measurement in addition to velocimetric measurements by means of hot wire anemometry and time-resolved particle image velocimetry. Three possible mechanisms for the so-called “separation-stall noise” have been identified in addition to a clear link between far-field noise, surface pressure, and velocity fields in the noise generation.- Open Access
- 3 July 2018
- Published by Springer Nature in Experiments in Fluids
- Vol. 59 (8) , 123
Experimental study on the forcing design for an intermittent injection
- 3 July 2018
- Published by Springer Nature in Experiments in Fluids
- Vol. 59 (8) , 123
Open AccessExperimental study on the forcing design for an intermittent injection
- 30 March 2018
- Published by Wiley in Wind Energy
- Vol. 21 (8) , 605-617
A wind‐tunnel study of the wake development behind wind turbines over sinusoidal hills
In the present work, the wake development behind small‐scale wind turbines is studied when introducing local topography variations consisting of a series of sinusoidal hills. Additionally, wind‐tunnel tests with homogeneous and sheared turbulent inflows were performed to understand how shear and ambient turbulence influence the results. The scale of the wind‐turbine models was about 1000 times smaller than full‐size turbines, suggesting that the present results should only be qualitatively extrapolated to real‐field scenarios. Wind‐tunnel measurements were made by means of stereoscopic particle image velocimetry to characterize the flow velocity in planes perpendicular to the flow direction. Over flat terrain, the wind‐turbine wake was seen to slowly approach the ground while it propagated downstream. When introducing hilly terrain, the downward wake deflection was enhanced in response to flow variations induced by the hills, and the turbulent kinetic energy content in the wake increased because of the speed‐up seen over the hills. The combined wake observed behind 2 streamwise aligned turbines was more diffused and when introducing hills, it was more prone to deflect towards the ground compared to the wake behind an isolated turbine. Since wake interactions are common at sites with multiple turbines, this suggested that it is important to consider the local hill‐induced velocity variations when onshore wind farms are analysed. Differences in the flow fields were seen when introducing either homogeneous or sheared turbulent inflow conditions, emphasizing the importance of accounting for the prevailing turbulence conditions at a given wind‐farm site to accurately capture the downstream wake development.
- 30 March 2018
- Published by Wiley in Wind Energy
- Vol. 21 (8) , 605-617
A wind‐tunnel study of the wake development behind wind turbines over sinusoidal hills
In the present work, the wake development behind small‐scale wind turbines is studied when introducing local topography variations consisting of a series of sinusoidal hills. Additionally, wind‐tunnel tests with homogeneous and sheared turbulent inflows were performed to understand how shear and ambient turbulence influence the results. The scale of the wind‐turbine models was about 1000 times smaller than full‐size turbines, suggesting that the present results should only be qualitatively extrapolated to real‐field scenarios. Wind‐tunnel measurements were made by means of stereoscopic particle image velocimetry to characterize the flow velocity in planes perpendicular to the flow direction. Over flat terrain, the wind‐turbine wake was seen to slowly approach the ground while it propagated downstream. When introducing hilly terrain, the downward wake deflection was enhanced in response to flow variations induced by the hills, and the turbulent kinetic energy content in the wake increased because of the speed‐up seen over the hills. The combined wake observed behind 2 streamwise aligned turbines was more diffused and when introducing hills, it was more prone to deflect towards the ground compared to the wake behind an isolated turbine. Since wake interactions are common at sites with multiple turbines, this suggested that it is important to consider the local hill‐induced velocity variations when onshore wind farms are analysed. Differences in the flow fields were seen when introducing either homogeneous or sheared turbulent inflow conditions, emphasizing the importance of accounting for the prevailing turbulence conditions at a given wind‐farm site to accurately capture the downstream wake development.