Alexander Petrovich Zhigadlo
Research Subjects
Alexander Petrovich Zhigadlo has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Anatoly Yu. Shonin
The Siberian State Automobile and Highway University (SibADI)
2 shared publications - Ivan A. Eychler
The Siberian State Automobile and Highway University (SibADI)
2 shared publications - Dmitry Likhachev
State Voronezh State University of Forestry and Technologies Named After G.F. Morozov
1 shared publication - Liudmila Trofimova
Siberian State Automobile and Highway University (SibADI)
1 shared publication - Oksana Yurievna Melnikova
Омский экономический институт
1 shared publication - Pavel V. Orlov
Siberian State Automobile and Highway University (SibADI)
1 shared publication
Latest Publications
- Open Access
- 3 March 2025
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 22 (1) , 54-67
Assessment of the organization expediency of the public transport complex "Privokzal'nyi" in Omsk city
Introduction. The article considers the need for a comprehensive assessment of the quality of transport services in the field of regular passenger transportation, justified by changes in both the provisions of the legislation of the Russian Federation and the requirements of the main consumer of these services – passengers. It is proposed to consider the issues of improving safety and comfort at large transport transfer hubs. The territory near the Omsk region railway station is chosen as an example.Materials and Methods. The work uses current regulatory legal acts of the federal and regional levels in the field of public transport services, data from the sociological survey of passengers, the results of measurements at the endpoints of the current route network of the Omsk region, existing registers of inter-municipal and municipal routes. The following research methods were used: analysis, survey, formalization.Results. Based on the analysis of statistical information and field observation data, the daily number of passengers and vehicles departing from the territory located near the Omsk railway station were determined. The obtained data allowed us to conclude that the studied territory with the second largest volume of passenger flow has absolutely no infrastructure that ensures the comfort and safety of transferring from municipal transport to inter-municipal routes. Based on the approved standards, the structure and area of the public transport complex have been determined, which makes it possible to eliminate the identified shortcomings.Discussion and conclusions. The obtained results suggest the need to organize a public transport complex and the possibility of its location on the territory near the railway station.
- 3 March 2025
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 22 (1) , 54-67
Open AccessAssessment of the organization expediency of the public transport complex "Privokzal'nyi" in Omsk city
Introduction. The article considers the need for a comprehensive assessment of the quality of transport services in the field of regular passenger transportation, justified by changes in both the provisions of the legislation of the Russian Federation and the requirements of the main consumer of these services – passengers. It is proposed to consider the issues of improving safety and comfort at large transport transfer hubs. The territory near the Omsk region railway station is chosen as an example.Materials and Methods. The work uses current regulatory legal acts of the federal and regional levels in the field of public transport services, data from the sociological survey of passengers, the results of measurements at the endpoints of the current route network of the Omsk region, existing registers of inter-municipal and municipal routes. The following research methods were used: analysis, survey, formalization.Results. Based on the analysis of statistical information and field observation data, the daily number of passengers and vehicles departing from the territory located near the Omsk railway station were determined. The obtained data allowed us to conclude that the studied territory with the second largest volume of passenger flow has absolutely no infrastructure that ensures the comfort and safety of transferring from municipal transport to inter-municipal routes. Based on the approved standards, the structure and area of the public transport complex have been determined, which makes it possible to eliminate the identified shortcomings.Discussion and conclusions. The obtained results suggest the need to organize a public transport complex and the possibility of its location on the territory near the railway station.
- Open Access
- 1 January 2025
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 21 (6) , 882-899
Methodology for assessing the state of transport services for the population of the subject of the Russian Federation on the example of the Omsk region
Introduction. Within the framework of the transformation of the passenger transportation industry of the Russian Federation, the relevance of assessing the current state of the public transport service system in the subjects of the Russian Federation is determined on the basis of the parameters laid down in current and prospective regulatory legal acts.Materials and Methods. The research uses current regulatory legal acts of the federal and regional levels in the field of public transport services, data from the administrative-territorial division of the subject of the Russian Federation, current registers of inter-municipal and municipal routes, up-to-date statistical information on the population. The following research methods were used: analysis, survey, formalization.Results. The research presents a methodology developed by the authors for rapid assessment of the current state of the public transport service system in the subject of the Russian Federation, including an algorithm for its application. The methodology is based on the assessment of six criteria, which are aggregated indicators of the parameters of public transport services in the areas of accessibility, safety, reliability and comfort. The results of the testing of the technique in the Omsk region are presented.Discussion and conclusions. The results obtained allow us to identify problem areas for which it is necessary to develop and implement measures to improve the quality of public transport services in the short term. The proposed methodology is not a substitute for the methods approved by the current regulatory legal acts, and can be used at the initial stage of development and updating of transport planning documents of the subject of the Russian Federation.
- 1 January 2025
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 21 (6) , 882-899
Open AccessMethodology for assessing the state of transport services for the population of the subject of the Russian Federation on the example of the Omsk region
Introduction. Within the framework of the transformation of the passenger transportation industry of the Russian Federation, the relevance of assessing the current state of the public transport service system in the subjects of the Russian Federation is determined on the basis of the parameters laid down in current and prospective regulatory legal acts.Materials and Methods. The research uses current regulatory legal acts of the federal and regional levels in the field of public transport services, data from the administrative-territorial division of the subject of the Russian Federation, current registers of inter-municipal and municipal routes, up-to-date statistical information on the population. The following research methods were used: analysis, survey, formalization.Results. The research presents a methodology developed by the authors for rapid assessment of the current state of the public transport service system in the subject of the Russian Federation, including an algorithm for its application. The methodology is based on the assessment of six criteria, which are aggregated indicators of the parameters of public transport services in the areas of accessibility, safety, reliability and comfort. The results of the testing of the technique in the Omsk region are presented.Discussion and conclusions. The results obtained allow us to identify problem areas for which it is necessary to develop and implement measures to improve the quality of public transport services in the short term. The proposed methodology is not a substitute for the methods approved by the current regulatory legal acts, and can be used at the initial stage of development and updating of transport planning documents of the subject of the Russian Federation.
- Open Access
- 6 January 2023
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 19 (6) , 842-857
Theoretical research and maintenance of electro hydraulically controlled injectors
Introduction.Nowadays the part of the diesel engines for KamAZ-740 cars are operated with fuel equipment, in which the injectors have hydro mechanical control. Their main disadvantage is the low fuel pressure in front of the injector openings (less than 60 MPa) and the lack of fuel supply control.The use of injectors with electro hydraulic control (EHC) increases the pressure in the injector cavity up to 250 MPa and control the fuel injection process. The disadvantage of the injectors with EHC is a structural complexity of a control valve, the difficulty of its regulation and coding. The object of the study is the injectors of KamAZ-740 diesel engine with electro hydraulic control of the atomizer needle stroke.The purpose of this work is to carry out theoretical research and improve the methods of maintenance of injectors with electro hydraulic control (control valve regulation and coding), which will increase their reliability, durability and ensure a reduction in diesel fuel consumption.Research methods.The study of the nozzle control valve is theoretical and calculated. The paper proposes a calculation method and performs theoretical studies for the influence of pressure (50 – 250 MPa) on the value of the effective flow section and the diameter of the nozzle holes of the sprayer.For the injectors with EHC, the control valve regulation procedure has been clarified, which consists in the fact that at the beginning of regulation, the main force acting on the ball from the side of the maximum pressure in the control chamber (for example, 200 MPa) equal to 76 N is calculated (see Figure 4). Then the required spring force of 100 N is determined (20-40% more, see Figure 5). Next, the strength of the electromagnet is estimated at 140 N (20 – 40% more of the spring force, see Figure 6).The results of theoretical research.The results of computational (theoretical) studies for the effective flow section of the sprayer and the diameter of the nozzle holes, depending on the pressure P in front of the nozzle holes, are presented.The paper defines.1. The forces acting on the ball (57 – 105 N) depending on the pressure in the control chamber (150 – 275 MPa). 2. Spring forces (40 – 140 N) with a stiffness of 40 N /mm, depending on its compression up to 3.5 mm. 3. The forces of the electromagnet (140 – 20 N) depending on the gap between the anchor and the core (0.2 – 0.5 mm).The method of restoring the required (rated) cyclic fuel supply when it changes as a result of replacing the control valve or adjusting is considered. The calculated values of fuel supply per cycle (mm3/cycle) from the activation time are given.Conclusion.The results of the study are intended for organizations and enterprises engaged in diagnostics, restoration, adjustment and coding of injectors with electro hydraulic control for the needle stroke of sprayers. The results of computational studies can be used to refine the methodology of maintenance of fuel systems with electronic control (Common Rail).
- 6 January 2023
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 19 (6) , 842-857
Open AccessTheoretical research and maintenance of electro hydraulically controlled injectors
Introduction.Nowadays the part of the diesel engines for KamAZ-740 cars are operated with fuel equipment, in which the injectors have hydro mechanical control. Their main disadvantage is the low fuel pressure in front of the injector openings (less than 60 MPa) and the lack of fuel supply control.The use of injectors with electro hydraulic control (EHC) increases the pressure in the injector cavity up to 250 MPa and control the fuel injection process. The disadvantage of the injectors with EHC is a structural complexity of a control valve, the difficulty of its regulation and coding. The object of the study is the injectors of KamAZ-740 diesel engine with electro hydraulic control of the atomizer needle stroke.The purpose of this work is to carry out theoretical research and improve the methods of maintenance of injectors with electro hydraulic control (control valve regulation and coding), which will increase their reliability, durability and ensure a reduction in diesel fuel consumption.Research methods.The study of the nozzle control valve is theoretical and calculated. The paper proposes a calculation method and performs theoretical studies for the influence of pressure (50 – 250 MPa) on the value of the effective flow section and the diameter of the nozzle holes of the sprayer.For the injectors with EHC, the control valve regulation procedure has been clarified, which consists in the fact that at the beginning of regulation, the main force acting on the ball from the side of the maximum pressure in the control chamber (for example, 200 MPa) equal to 76 N is calculated (see Figure 4). Then the required spring force of 100 N is determined (20-40% more, see Figure 5). Next, the strength of the electromagnet is estimated at 140 N (20 – 40% more of the spring force, see Figure 6).The results of theoretical research.The results of computational (theoretical) studies for the effective flow section of the sprayer and the diameter of the nozzle holes, depending on the pressure P in front of the nozzle holes, are presented.The paper defines.1. The forces acting on the ball (57 – 105 N) depending on the pressure in the control chamber (150 – 275 MPa). 2. Spring forces (40 – 140 N) with a stiffness of 40 N /mm, depending on its compression up to 3.5 mm. 3. The forces of the electromagnet (140 – 20 N) depending on the gap between the anchor and the core (0.2 – 0.5 mm).The method of restoring the required (rated) cyclic fuel supply when it changes as a result of replacing the control valve or adjusting is considered. The calculated values of fuel supply per cycle (mm3/cycle) from the activation time are given.Conclusion.The results of the study are intended for organizations and enterprises engaged in diagnostics, restoration, adjustment and coding of injectors with electro hydraulic control for the needle stroke of sprayers. The results of computational studies can be used to refine the methodology of maintenance of fuel systems with electronic control (Common Rail).
- Open Access
- 17 March 2022
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 19 (1) , 74-83
Activities for road transport enterprises on indicators of workers and rolling stock productivity planning
Introduction. The emphasis is placed on modern requirements in the development of transport industry by improving the planning of the activities of road transport enterprises in terms of indicators that determine the productivity of workers and rolling stock, which are a function of the demand for transportation. The results of the activities of road transport enterprises depend on the labour productivity of each employee performing a specific function for the implementation of a specific contract and making a profit.Materials and methods. Planning is carried out using the conceptual provisions of the current planning of the work of a trucking company, taking into account the relationship of activities and the demand for transportation, methods of probability theory and mathematical statistics, scientific principles of education and training of workers for the transport industry.Results. The application of a new approach to planning is to combine the productivity of workers and the production of rolling stock of the Motor Transport Enterprises (MTE). This made it possible to develop a mathematical model and methodology, which takes into account that the productivity of workers must ensure the receipt of the planned income for each contract and its value will be planned within the confidence limits. When planning, probabilistic events are taken into account that occur during the development of sectors of the economy of the Russian Federation and affect the need for skilled staff. Mathematical modeling is carried out in relation to the real operating conditions of cargo transportation and specific functions of employees. The number of rolling stock and the required number of employees are determined by the development of rolling stock, by the development of a specific production function by an employee in modern conditions of contractual relations.Discussion and conclusions. The results of the study are intended for the practice of road transport enterprises at the stage of determining indicators of labor productivity of workers and rolling stock.
- 17 March 2022
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 19 (1) , 74-83
Open AccessActivities for road transport enterprises on indicators of workers and rolling stock productivity planning
Introduction. The emphasis is placed on modern requirements in the development of transport industry by improving the planning of the activities of road transport enterprises in terms of indicators that determine the productivity of workers and rolling stock, which are a function of the demand for transportation. The results of the activities of road transport enterprises depend on the labour productivity of each employee performing a specific function for the implementation of a specific contract and making a profit.Materials and methods. Planning is carried out using the conceptual provisions of the current planning of the work of a trucking company, taking into account the relationship of activities and the demand for transportation, methods of probability theory and mathematical statistics, scientific principles of education and training of workers for the transport industry.Results. The application of a new approach to planning is to combine the productivity of workers and the production of rolling stock of the Motor Transport Enterprises (MTE). This made it possible to develop a mathematical model and methodology, which takes into account that the productivity of workers must ensure the receipt of the planned income for each contract and its value will be planned within the confidence limits. When planning, probabilistic events are taken into account that occur during the development of sectors of the economy of the Russian Federation and affect the need for skilled staff. Mathematical modeling is carried out in relation to the real operating conditions of cargo transportation and specific functions of employees. The number of rolling stock and the required number of employees are determined by the development of rolling stock, by the development of a specific production function by an employee in modern conditions of contractual relations.Discussion and conclusions. The results of the study are intended for the practice of road transport enterprises at the stage of determining indicators of labor productivity of workers and rolling stock.
- 1 January 2022
- Published by FSB EIHE Omsk State Technical University in Omsk Scientific Bulletin
Selection of cam mechanisms for driving the plunger of high-pressure pump of diesel engines using Mathcad program
The purpose of the article is to select the cam profile (with equal design parameters) for driving the plunger of a high-pressure pump that provides the maximum speed and permissible acceleration of the pusher. A method of selecting a cam profile by analyzing combined graphs of changes in the path, speed, and acceleration of a cam pusher of various profiles using the Mathcad program is proposed. Calculations have been performed and combined graphs of changes in the path, speed, and acceleration of the cam pusher with tangential, convex, and concave profiles have been constructed. A comparative analysis of the combined graphs showed that the maximum speed of the cam pusher with a concave profile is 1,5 times greater than for cams with a tangential or convex profile. A cam with a concave profile is recommended for driving pump plungers of low-speed marine diesel engines (up to 250 min–1). To create ultra–high pressures (more than 120 MPa), the fuel supply system must be batterytype with a drive of small diameter plungers (4–6 mm) from an eccentric shaft with a special-shaped washer and electronically controlled injectors.
- 1 January 2022
- Published by FSB EIHE Omsk State Technical University in Omsk Scientific Bulletin
Selection of cam mechanisms for driving the plunger of high-pressure pump of diesel engines using Mathcad program
The purpose of the article is to select the cam profile (with equal design parameters) for driving the plunger of a high-pressure pump that provides the maximum speed and permissible acceleration of the pusher. A method of selecting a cam profile by analyzing combined graphs of changes in the path, speed, and acceleration of a cam pusher of various profiles using the Mathcad program is proposed. Calculations have been performed and combined graphs of changes in the path, speed, and acceleration of the cam pusher with tangential, convex, and concave profiles have been constructed. A comparative analysis of the combined graphs showed that the maximum speed of the cam pusher with a concave profile is 1,5 times greater than for cams with a tangential or convex profile. A cam with a concave profile is recommended for driving pump plungers of low-speed marine diesel engines (up to 250 min–1). To create ultra–high pressures (more than 120 MPa), the fuel supply system must be batterytype with a drive of small diameter plungers (4–6 mm) from an eccentric shaft with a special-shaped washer and electronically controlled injectors.
- Open Access
- 8 September 2019
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 16 (4) , 432-445
NEW APPROACH TO ADDITIONAL LEFT-TURN SECTIONS OF THE TRAFFIC SIGNAL REGULATION
Introduction. The paper describes methods of using the additional left-turn phase of regulation. The authors view the main foreign and domestic methods used in the specialization of the left turn in a separate phase of regulation. To propose a new approach to the specialization of the left-turn direction in a separate phase of regulation the authors investigate one of the most loaded intersections in Voronezh and determine the main characteristics of the traffic flow. Therefore, the authors suggest new parameters in choosing of the necessary method of traffic organization at controlled intersections.Methods and materials. The paper analyses the main methods, which were conditionally related to two approaches: the accident rate of the site and the characteristics of the traffic flow (speed and intensity of the left-turn flow). The authors explained that the new approach, which took into account such parameters as speed, vehicle delays and queue length, allowed effectively controlling the intersection due to the optimal choice of the necessary traffic organization method and due to the result of changes in the parameters by combining the intensity of the left-turn flow and forward flow.Results. The authors developed the approach to the additional left-turn section introduction at the controlled intersection based on a comparison of the left-turn intensity and forward flow and on the analysis of changes in the main characteristics of the traffic flow (speed, vehicle delays and queue length).Discussion and conclusions. The authors concluded that it is necessary to use the proposed approach at the stage of modeling, design and reorganization of the regulated area on the basis of changes in the main characteristics of the traffic flow.
- 8 September 2019
- Published by Siberian State Automobile and Highway University (SibADI) in The Russian Automobile and Highway Industry Journal
- Vol. 16 (4) , 432-445
Open AccessNEW APPROACH TO ADDITIONAL LEFT-TURN SECTIONS OF THE TRAFFIC SIGNAL REGULATION
Introduction. The paper describes methods of using the additional left-turn phase of regulation. The authors view the main foreign and domestic methods used in the specialization of the left turn in a separate phase of regulation. To propose a new approach to the specialization of the left-turn direction in a separate phase of regulation the authors investigate one of the most loaded intersections in Voronezh and determine the main characteristics of the traffic flow. Therefore, the authors suggest new parameters in choosing of the necessary method of traffic organization at controlled intersections.Methods and materials. The paper analyses the main methods, which were conditionally related to two approaches: the accident rate of the site and the characteristics of the traffic flow (speed and intensity of the left-turn flow). The authors explained that the new approach, which took into account such parameters as speed, vehicle delays and queue length, allowed effectively controlling the intersection due to the optimal choice of the necessary traffic organization method and due to the result of changes in the parameters by combining the intensity of the left-turn flow and forward flow.Results. The authors developed the approach to the additional left-turn section introduction at the controlled intersection based on a comparison of the left-turn intensity and forward flow and on the analysis of changes in the main characteristics of the traffic flow (speed, vehicle delays and queue length).Discussion and conclusions. The authors concluded that it is necessary to use the proposed approach at the stage of modeling, design and reorganization of the regulated area on the basis of changes in the main characteristics of the traffic flow.
- Open Access
- 28 June 2018
- Published by Novosibirsk State Pedagogical University in Novosibirsk State Pedagogical University Bulletin
- Vol. 8 (3) , 139-153
Ecological competence of bachelors of socio-economic profile in the context of the education principles for sustainable development
- 28 June 2018
- Published by Novosibirsk State Pedagogical University in Novosibirsk State Pedagogical University Bulletin
- Vol. 8 (3) , 139-153
Open AccessEcological competence of bachelors of socio-economic profile in the context of the education principles for sustainable development