VBVlastimil Bohac

Vlastimil Bohac

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Vlastimil Bohac has a total of 62 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Investigation of thermophysical parameters of historical fir wood using hot disk method under room ambience

    by Rupali Tiwari, Richard Hrčka, Vlastimil Boháč, Roman Réh, Valentina Lo Giudice, Luigi Todaro, Lubos Kristak

    The study aims were to investigate the Thermophysical properties of fir wood (Abies alba Mill.) using the Hot Disk transient method under standard room conditio


  • Open Access

    The influence of the flatness of the particleboard composite samples on the accuracy of the measurement of thermal properties by pulse transient method

    by Vlastimil Boháč, Rupali Tiwari, Lubos Kristak, Roman Réh, Ján Hudec, Vladimír Štofanik, Valentina Lo Giudice, Luigi Todaro

    Recently, new composite materials based on natural wood-based materials have been increasingly used in modern construction of houses because of their good physical, mechanical and thermal insulation properties. This raises the need to characterize their Thermophysical properties. As part of our project ’Research of selected properties of sustainable insulating materials with the potential for use in wooden buildings’, we measured samples of High and Middle density particleboards made from chips of Turkey oak wood (Turkish oak HDPB, Turkish oak MDPB) and samples made from mixture of Turkey Oak wood and Orange wood (OOPB). A cuboid model for the pulse transient method was used to estimate the parameters. The model takes into account the cuboid geometry of the sample with a square base, the heat losses from the free surface of the sample to the surroundings using the coefficient of heat transfer from the surface of the sample to the surroundings in the lateral direction, as well as the infinitely large heat capacity of the heat exchangers between which the sample is placed. The heat transfer coefficient between the heat source and the sample is infinitely large. The surface of the particleboard is usually rough and porous due to the size and nature of its particles. In addition, the interfaces of the three parts of the sample set are hand-polished, so that the edges and corners are not perfectly flush with the central area of the surface. As a result of manual polishing, the interfaces at the corners and edges of the sample parts usually have air-filled gaps. Free gaps cause additional thermal resistance to heat flow from the heat source to the body of the sample. Then, the coefficient of heat transfer from the heat source to the sample is not infinitely large and does not correspond to the conditions of the cuboid model. While the Turkey Oak HDPB had a perfectly flat surface, the Orange-Oak PB suffered from loose gaps at the interfaces. Therefore, we filled them with silicone glue as a thermal contact agent and measured them again. The consequence of flatness differences for all results was discussed within the theoretical analysis based on sensitivity coefficients, uncertainty calculations, as well as the assumption of a thermally dependent heat transfer coefficient between the heat source, air gap and the sample. The criterion for the quality of the fitting of the thermal responses by the cuboid model was the residual graph within the thermal noise of the thermocouple ± 0.005 K.

  • Open Access

    Thermal properties of Oak high density board measured by the pulse transient method for different heat pulse energy

    by Vlastimil Boháč, Rupali Tiwari, Luboš Krišťák, Luigi Todaro, Valentina Lo Giudice, Viliam Vretenár

    The energy efficiency of buildings is assessed on the base of thermal insulation properties that can help to save energy costs as well as environment. The wooden materials are widely used as they become significantly recyclable and nature-friendly. Their thermal insulation properties have to be known for construction purposes. The modern experimental methods for the Thermophysical measurements are highly desired in this field. The methodology for the experimental measurement setup has to be optimized and possible disturbing effects at measurements have to be taking into account. The first more sophisticated method is to include disturbing effect into the model or to use the second one by arrangement of the sample set geometry as close as possible to the ideal state. The pulse transient method is relatively fast in comparison with stationary methods. It is simple for experimental arrangement and reliable for large scale of materials. Measurement reliability in this paper was tested by increasing the heat pulse energy, as the estimated Thermophysical parameters have to be independent on used power. The data scattering found for all measurements was found below 2% for all Thermophysical parameters.


  • The transient method measurements of thermophysical properties of non-solid clay loam

    by Vlastimil Boháč, Peter Dieška, Viliam Vretenár, Ján Hudec, Vladimír Lukáč

    The In the frame of extending the renewable energy systems, the use of the shallow geological bedrock below the houses is used for the seasonal heat storage purposes. Thus, the knowledge of the thermophysical properties of the soft clay loam materials present in the bedrock is important. On the basis of the known thermal diffusivity, thermal conductivity and specific heat of the materials around the energetic needle, one can calculate the time dependency of the heat dissipated and transferred into the surrounding. This allows calculating the temperature maps that can specify in more detail the heat penetration depth during the seasonal storage and pumping out of the heat accumulated during the year seasons. The aim is to optimize the efficiency of the system. The clay loams in the free nature contain high level of the moisture and thus have high values of specific heat. The pulse transient method was used to get the thermophysical parameters of these materials. Specimens were drilled out from the bedrock at depths 50, 150 and 250cm from the surface. The measured values of equilibrium sorption moisture show that obtained materials are very different. In the paper we show the possible influence of the redistribution of water content during the shooting of the heat pulse. The water redistribution deforms the temperature response. This effect was avoided by lowering the heat pulse power to minimal values that still allows the evaluation of the measurement.

  • New way of measurement of thermophysical properties of clay loam materials by transient methods

    by Vlastimil Boháč, Peter Dieška, Viliam Vretenár, Vladimír Lukáč

    The problem of the measurement of clay loam materials in plastic consistency is more or less difficult as they can change the shape during the long time measurements. The specimen thickness is expected as the constant during all the experiment measured by transient pulse method. In a case of plastic clay loam, it can change the form during the measurement because of the squeeze of the material even under the gravity condition. Thus the specimen surface wall should be reinforced by special dimensionally well-defined thin wall container. In this paper the special container in a form of thin tube rings bounded by central annular ring was constructed and used for the measurements. The heat source was inserted into the tube rings through the nozzle in the middle part and the thermocouple was inserted through the drilled openings at defined distance from the heat source. System clamped the heat source together with the rings at desired distance from the thermocouple. This distance represents the thickness of tested specimen. The soft plastic material fill the inner space of tube rings in such a way to fulfill the geometry conditions for this method. The need of soft clay loam material measurement is to test its thermal properties because of the interest to use it as the heat storage material below the buildings. The measured clay loam containing some moisture has quite high values of specific heat and thus the use of it as the heat storage material is promising.


  • New Planar Disc Transient Method for the Measurement of Thermal Properties of Materials

    by Vlastimil Bohac, Peter Dieška, Viliam Vretenár, Danica Opatt-Fidríková, Vladimír Štofanik, Marian Markovič

    Recently the physical model for the temperature field generated by thermophysical single-probe sensor in a shape of planar disc has been derived. The model accounts cylindrical sample having final radius and infinite length. The prototype of measuring electronics RTA was build that operates with auto balancing bridge. For the measurements the single-transition method is used. While the measurement error of the temperature response measured by thermocouple was 1% at the height of temperature response 1°C, the sensitivity of the measurement with the automatically balanced bridge is better and the signal to noise ratio is improved about 10 times. The measuring electronics was tested for measuring the temperature response using a single-sensor. This sensor generates the heat pulse and sense the temperature response in the same time. The next advantage is that the temperature response to the generated step-wise pulse is much smaller and it can be reduced to the level of 1-8° C compared to stationary method like guarded hot plate method. The effect of the temperature field generated by the probe is much smaller, which in the case of measurement of porous materials at the presence of moisture is beneficial, as the resulting redistribution of moisture under the created temperature gradient is negligible. There were derived basic models for the evaluation of this type of experiment. The probe should be in form of full cylinder or an annulus. The derived temperature function counts the outer and inner diameter of annulus. Putting the inner radius to zero we get the solution for full circle probe, so the model is universal. The model counts also the heat losses from the outer surface of the sample, when the time of measurement exceed the time when the penetration depth of generated heat pulse rich the outer radius of sample. The estimated output parameters from single measurement are the thermal conductivity, thermal diffusivity and specific heat. The heat transfer coefficient is additional parameter fitted as free parameter of the model.


  • Open Access

    Erratum to: Thermophysical Properties of Heterogeneous Structures Measured by Pulse Transient Method

    by L’. Kubičár, V. Bohač, V. Vretenár, Š. Barta, G. Neuer, R. Brandt


  • Hot-Ball Method for Measuring Thermal Conductivity

    by L’udovít Kubičár, Viliam Vretenár, Vladimír Štofanik, Vlastimil Boháč


  • Study of Phase Transitions by Transient Methods

    by L. Kubičár, V. Vretenár, V. Boháč

    The present paper deals with the application of the transient techniques for thermophysical analysis of the structural changes in materials. The technique has been applied for study of equilibrium transitions as well as for kinetic transitions. A special methodology has been developed to study kinetic transitions like crystallization, melting, etc. in a “pseudo-equilibrium states” by the help of porous structures. The paper includes three different issues: the transient methods for measuring thermodynamic and transport parameters, data analysis and application of the pulse transient method for measurements of materials in thermodynamic equilibrium, pseudoequilibrium and in non-equilibrium (quasi-equilibrium) states. Equilibrium transitions in CsPbCl3 and CsPbBr3 single crystals, kinetic transitions of freezing and thawing water in porous stones and non-equilibriums states in E-glass and Al2O3 ceramics during sintering have been studied.