Lyly Nyl Ismail
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lyly Nyl Ismail has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
M. Rusop
Universiti Teknologi MARA
12 shared publicationsZ. Habibah
NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM) Shah Alam, Selangor, Malaysia
7 shared publications- Mohamad Hafiz Mamat
NANO-SciTech Centre (NST), Institute of Science (IOS), Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor, Malaysia
5 shared publications Mohamad Rusop Mahmood
Universiti Teknologi MARA (UiTM)
5 shared publications- Sukreen Hana Herman
Universiti Teknologi MARA
5 shared publications - Mohamad Hafiz Mohd Wahid
Universiti Teknologi MARA
4 shared publications
Latest Publications
- 31 August 2013
- Published by Elsevier in Microelectronic Engineering
- Vol. 108, 138-144
Novel encapsulated ITO/arc-ZnO:TiO2 antireflective passivating layer for TCO conducting substrate prepared by simultaneous radio frequency-magnetron sputtering
- 31 August 2013
- Published by Elsevier in Microelectronic Engineering
- Vol. 108, 138-144
Novel encapsulated ITO/arc-ZnO:TiO2 antireflective passivating layer for TCO conducting substrate prepared by simultaneous radio frequency-magnetron sputtering
- 29 November 2012
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 229-231, 228-232
Effect of Milling Time on the Structural Properties of Titanium Dioxide Nanopowder
This paper report the effect of milling time on the structural properties of TiO2 nanopowder prepared from sol-gel milling process. The synthesized TiO2 nanopowders have been characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and Fourier transform infrared (FTIR). XRD result reveals that the TiO2 nanopowder in anatase phase is detected. The morphology of the TiO2 nanopowder change obviously with the increase of the milling time. Further, FTIR results found the sharp peaks of Ti-O-Ti and Ti-O bonding at below 600 cm-1 for all TiO2 nanopowder.
- 29 November 2012
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 229-231, 228-232
Effect of Milling Time on the Structural Properties of Titanium Dioxide Nanopowder
This paper report the effect of milling time on the structural properties of TiO2 nanopowder prepared from sol-gel milling process. The synthesized TiO2 nanopowders have been characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM) and Fourier transform infrared (FTIR). XRD result reveals that the TiO2 nanopowder in anatase phase is detected. The morphology of the TiO2 nanopowder change obviously with the increase of the milling time. Further, FTIR results found the sharp peaks of Ti-O-Ti and Ti-O bonding at below 600 cm-1 for all TiO2 nanopowder.
- 8 October 2012
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 576, 582-585
Dielectric Properties of PVDF-TrFE/PMMA: TiO2 Multilayer Dielectric Thin Films
This paper reports on the dielectric properties of multilayer PVDF-TrFE/PMMA:TiO2 thin film. Two samples were fabricated on ITO substrates; one with PVDF-TrFE only and another PMMA:TiO2 on PVDF-TrFE on (PVDF-TrFE/PMMA:TiO2). Both samples were produced by spin coating method. Dielectric properties were characterized using impedance spectroscopic. Dielectric constant, k, capacitance and dielectric loss, tan δ values of PMMA:TiO2/PVDF-TrFE were measured in the frequency range 0 – 50 kHz. The result for dielectric loss did not show any significant different between the samples with and without nanocomposite PVDF-TrFE layer. However, the dielectric constant are affected when depositing a nanocomposite PVDF-TrFE layer on PMMA:TiO2. The dielectric constant is decreased by 0.3 from 7.9 to 7.6.
- 8 October 2012
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 576, 582-585
Dielectric Properties of PVDF-TrFE/PMMA: TiO2 Multilayer Dielectric Thin Films
This paper reports on the dielectric properties of multilayer PVDF-TrFE/PMMA:TiO2 thin film. Two samples were fabricated on ITO substrates; one with PVDF-TrFE only and another PMMA:TiO2 on PVDF-TrFE on (PVDF-TrFE/PMMA:TiO2). Both samples were produced by spin coating method. Dielectric properties were characterized using impedance spectroscopic. Dielectric constant, k, capacitance and dielectric loss, tan δ values of PMMA:TiO2/PVDF-TrFE were measured in the frequency range 0 – 50 kHz. The result for dielectric loss did not show any significant different between the samples with and without nanocomposite PVDF-TrFE layer. However, the dielectric constant are affected when depositing a nanocomposite PVDF-TrFE layer on PMMA:TiO2. The dielectric constant is decreased by 0.3 from 7.9 to 7.6.
- 8 October 2012
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 576, 417-420
Effect of TiO2 Nanofiller on Nanocomposited PMMA/TiO2 Thin Film
In this study, PMMA/TiO2 nanocomposite thin films were prepared by using sonication spin coating technique. The PMMA and TiO2 solution were mixed together and sonicated for 1h to confirm the homogeneity of the sample. The thin films obtained were then measured using atomic force microscopy (AFM), field emission scanning electron microscopy (FESEM) and Fourier transform infrared (FTIR). FESEM micrograph reveals that the uniformity increases with the increase of TiO2 weight percentage.
- 8 October 2012
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 576, 417-420
Effect of TiO2 Nanofiller on Nanocomposited PMMA/TiO2 Thin Film
In this study, PMMA/TiO2 nanocomposite thin films were prepared by using sonication spin coating technique. The PMMA and TiO2 solution were mixed together and sonicated for 1h to confirm the homogeneity of the sample. The thin films obtained were then measured using atomic force microscopy (AFM), field emission scanning electron microscopy (FESEM) and Fourier transform infrared (FTIR). FESEM micrograph reveals that the uniformity increases with the increase of TiO2 weight percentage.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 65-68
Effects of PMMA concentration on PMMA-based organic capacitor behavior
This paper reports the behavior of poly (methyl methacrylate) (PMMA) as insulator films. The PMMA concentrations were from 0.3, 0.6, 0.9 to 1.2 g. The electrical and dielectric properties results showed that PMMA concentration influenced the insulator behavior in the capacitor. The resistivity increased and the leakage current reduced from 10-2 A/cm2 to 10-7 A/cm2 when the PMMA concentrations were increased.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 65-68
Effects of PMMA concentration on PMMA-based organic capacitor behavior
This paper reports the behavior of poly (methyl methacrylate) (PMMA) as insulator films. The PMMA concentrations were from 0.3, 0.6, 0.9 to 1.2 g. The electrical and dielectric properties results showed that PMMA concentration influenced the insulator behavior in the capacitor. The resistivity increased and the leakage current reduced from 10-2 A/cm2 to 10-7 A/cm2 when the PMMA concentrations were increased.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 9, 18-22
Dielectric constant of PVDF/MgO nanocomposites thin films
This study investigates the effect of varying loading percentage of MgO on the dielectric constant of Poly (vinylideneflouride)/Magnesium Oxide (PVDF/MgO) nanocomposite thin films. PVDF/MgO nanocomposite spin coated thin films were successfully fabricated and characterized. PVDF and nanocomposites solutions with loading percentage of MgO at 3, 5, 7, 9, and 11% were spin coated on Al-glass substrates at 1500rpm. The optimum percentage of PVDF/MgO thin film obtained from the dielectric measurement was 7%. The dielectric constant of PVDF/Mg(7%) nanocomposite at frequency 10 3 Hz was 21, with low dielectric loss and absence of visible film defects, as evident by FE-SEM images. In FTIR, broad bonding peaks at 840 and 880 cm -1 can be observed. Both bonding represented the -CH 2 and -CF 2 groups of PVDF, which indicated high β-phase content that attributed to the increment in the dielectric constant of PVDF/MgO(7%) nanocomposite. The PVDF/MgO(7%) nanocomposite is favorable for low frequency electronic application such as capacitor.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 9, 18-22
Dielectric constant of PVDF/MgO nanocomposites thin films
This study investigates the effect of varying loading percentage of MgO on the dielectric constant of Poly (vinylideneflouride)/Magnesium Oxide (PVDF/MgO) nanocomposite thin films. PVDF/MgO nanocomposite spin coated thin films were successfully fabricated and characterized. PVDF and nanocomposites solutions with loading percentage of MgO at 3, 5, 7, 9, and 11% were spin coated on Al-glass substrates at 1500rpm. The optimum percentage of PVDF/MgO thin film obtained from the dielectric measurement was 7%. The dielectric constant of PVDF/Mg(7%) nanocomposite at frequency 10 3 Hz was 21, with low dielectric loss and absence of visible film defects, as evident by FE-SEM images. In FTIR, broad bonding peaks at 840 and 880 cm -1 can be observed. Both bonding represented the -CH 2 and -CF 2 groups of PVDF, which indicated high β-phase content that attributed to the increment in the dielectric constant of PVDF/MgO(7%) nanocomposite. The PVDF/MgO(7%) nanocomposite is favorable for low frequency electronic application such as capacitor.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 182-185
Modulus and thermal properties of free standing PMMA/TiO2 nanocomposite films
TiO 2 nanopowder (0-20 w%) has been introduced in the PMMA matrix using the single step of sonication method to produce the PMMA/TiO 2 nanocomposite films in the free standing form. The PMMA and TiO 2 solution were mixed in the sonication bath. The effects on Tg, thermal degradation and also modulus of the PMMA/TiO 2 nanocomposites films were investigated. The properties of the nanocomposite films were depending on the dispersion of TiO 2 nanopowder in the PMMA matrix. The results of differential scanning calorimetry (DSC), thermo gravimetric analysis (TGA), and dynamic mechanical analysis (DMTA) were discussed in this paper.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 182-185
Modulus and thermal properties of free standing PMMA/TiO2 nanocomposite films
TiO 2 nanopowder (0-20 w%) has been introduced in the PMMA matrix using the single step of sonication method to produce the PMMA/TiO 2 nanocomposite films in the free standing form. The PMMA and TiO 2 solution were mixed in the sonication bath. The effects on Tg, thermal degradation and also modulus of the PMMA/TiO 2 nanocomposites films were investigated. The properties of the nanocomposite films were depending on the dispersion of TiO 2 nanopowder in the PMMA matrix. The results of differential scanning calorimetry (DSC), thermo gravimetric analysis (TGA), and dynamic mechanical analysis (DMTA) were discussed in this paper.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 96, 709-713
The surface morphology and bonding properties of free standing PMMA/TiO2 nanocomposite films
PMMA/TiO 2 nanocomposite films in free standing form were prepared at different amount of TiO 2 nanoparticles by using sonication method. The PMMA powder and TiO 2 nanopowder were dissolved into the toluene solution and sonicated for 1 h to confirm the homogeneity of the mixture. The FESEM micrographs reveal that PMMA/TiO 2 nanocomposite contain 4 wt% TiO 2 nanoparticles can produced the homogenous mixture with only little crack observed in the sample compared to other samples. Even the agglomerations were observed in other samples, all the TiO 2 nanoparticles were fully dispersed in the PMMA matrix. The EDX results reveal the existence of the titanium and oxygen element in the nanocomposite films and FTIR results reveal the bonding properties between these two materials. Raman spectra of the PMMA/TiO 2 nanocomposite films also were discussed in this paper.
- 1 September 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 96, 709-713
The surface morphology and bonding properties of free standing PMMA/TiO2 nanocomposite films
PMMA/TiO 2 nanocomposite films in free standing form were prepared at different amount of TiO 2 nanoparticles by using sonication method. The PMMA powder and TiO 2 nanopowder were dissolved into the toluene solution and sonicated for 1 h to confirm the homogeneity of the mixture. The FESEM micrographs reveal that PMMA/TiO 2 nanocomposite contain 4 wt% TiO 2 nanoparticles can produced the homogenous mixture with only little crack observed in the sample compared to other samples. Even the agglomerations were observed in other samples, all the TiO 2 nanoparticles were fully dispersed in the PMMA matrix. The EDX results reveal the existence of the titanium and oxygen element in the nanocomposite films and FTIR results reveal the bonding properties between these two materials. Raman spectra of the PMMA/TiO 2 nanocomposite films also were discussed in this paper.
- 1 June 2012
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 51 (6S) , 06FG09
Effect of Solvent on the Dielectric Properties of Nanocomposite Poly(methyl methacrylate)-Doped Titanium Dioxide Dielectric Films
A poly(methyl methacrylate)-doped titanium dioxide (PMMA:TiO2) nanocomposite film was obtained by spin coating the nanocomposite solution onto a silicon substrate. The nanocomposite solutions were prepared by dissolving the PMMA and TiO2nanopowder in three different types of organic solvent, namely, toluene, tetrahydrofuran (THF), and acetone. We found that the dielectric properties of the PMMA:TiO2nanocomposite are dependent on the type of solvent used. The dielectric properties measured at a frequency of 1 kHz showed that acetone gives the highest dielectric constant and capacitance compared with toluene and THF. Toluene gives the lowest dielectric loss among the three. The topography and roughness of the PMMA:TiO2nanocomposite indicate that a particular solvent results in a different kind of surface morphology.
- 1 June 2012
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 51 (6S) , 06FG09
Effect of Solvent on the Dielectric Properties of Nanocomposite Poly(methyl methacrylate)-Doped Titanium Dioxide Dielectric Films
A poly(methyl methacrylate)-doped titanium dioxide (PMMA:TiO2) nanocomposite film was obtained by spin coating the nanocomposite solution onto a silicon substrate. The nanocomposite solutions were prepared by dissolving the PMMA and TiO2nanopowder in three different types of organic solvent, namely, toluene, tetrahydrofuran (THF), and acetone. We found that the dielectric properties of the PMMA:TiO2nanocomposite are dependent on the type of solvent used. The dielectric properties measured at a frequency of 1 kHz showed that acetone gives the highest dielectric constant and capacitance compared with toluene and THF. Toluene gives the lowest dielectric loss among the three. The topography and roughness of the PMMA:TiO2nanocomposite indicate that a particular solvent results in a different kind of surface morphology.