DADmytro Abraimov

Dmytro Abraimov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dmytro Abraimov has a total of 108 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Simulation of self-arresting screening current stress damage in a > 900 MPa REBCO coil using detailed conductor models

    by Jeseok Bang, Jonathan Lee, Garfield Murphy, Kwangmin Kim, Griffin Bradford, Jan Jaroszynski, Dmytro Abraimov, Najib Cheggour, Fumitake Kametani, David Larbalestier

    Screening current in REBCO-coated conductors amplifies the Lorentz force. In high fields, screening current stress (SCS) can cause excessive magnetic stress and subsequent plastic deformation of the conductor. This is recognized as a key issue in the high-field, high-stress REBCO magnet technology at present, since such plastic damage degrades local superconductivity and eventually affects the coil performance. Although the importance of SCS has been widely recognized and extensively investigated, relevant studies are mostly limited to the calculation of peak stress and strain, rarely focusing on the damage initiation and propagation mechanism. Additionally, simulation studies of REBCO coils consider key conductor properties by referring to measured results in the literature, but rarely employ measurements obtained from the conductor used in the tested coil. We therefore performed an integrated conductor-to-coil study. First, we selected one of our previous high-field REBCO coil experiments, where the coil did not experience quench damage, although SCS-initiated wavy plastic damage and subsequent coil performance degradation were observed during the test. The conductor used in the coil was parameterized and formulated in detail based on measured electromagnetic and mechanical properties. Then, simulation work was performed to investigate plastic damage initiation and propagation, demonstrating that SCS caused local plastic damage, degrading local J c and reducing global I c , changing the effective current path, and shifting the electric field center towards the undamaged region from the physical center. One key finding is that plastic damage propagation becomes self-arresting and remains confined to a limited region of the conductor width because local J c degradation redistributes the screening current and consequently alters the stress distribution. This paper presents a detailed conductor model and SCS simulations and discusses their agreement with experimental observations.

  • Machine learning-based characterization of surface defects in REBCO tapes

    by Nandana Menon, Jean-Francois Croteau, Dmytro Abraimov, Hannah Matos-Pimentel, Yavuz Oz, Ian Pong, Carina Zha, Nicole Bishop, Jozef Kvitkovic, Jun Lu, et al.

    REBCO coated conductors are of significant interest for high-field superconducting applications owing to their exceptional critical current retention under high magnetic fields. However, depending on the fabrication route, microstructural inhomogeneities such as porosity, Cu x O precipitates, and a -axis oriented grains can emerge at various length scales, disrupting current transport and limiting the critical current density. This study investigates and characterizes such defects in commercial REBCO conductors of varying specifications. Top-view scanning electron microscope (SEM) images of the REBCO layer were acquired following chemical etching of Cu and Ag layers to expose the microstructure for analysis. Conventional image analysis and segmentation techniques prove insufficient for reliably quantifying these defects, while manual identification remains prohibitively labor-intensive. To overcome these limitations, a machine learning approach is explored to enable rapid, automated, and accurate defect detection. Specifically, an open-source computer vision model, Mask region-based convolutional neural network, is fine-tuned on domain-specific SEM image data. The fine-tuned model achieved a validation mean average precision of 45.23% and enabled quantitative defect analysis across 63 tapes. Partial correlation analysis, controlling for confounding between defect types, revealed independent associations with critical current density that varied in strength and sign across defect types and measurement conditions. These findings motivate further targeted characterization to establish the microstructural origins of these relationships and inform conductor optimization.

  • Open Access

    Variation in supercurrent connectivity and vortex pinning of state-of-the-art pulsed laser deposited RE Ba 2 Cu 3 O 7-x coated conductors

    by Aixia Xu, Yan Xin, Hayden Kinstler, Nonoko Kametani, Cade Watson, Dmytro Abraimov, Jan Jaroszynski, Chiara Tarantini, Fumitake Kametani, David C Larbalestier

    RE Ba 2 Cu 3 O 7-x ( RE BCO, RE : rare earth) coated conductors suffer from great critical current I c differences between different manufacturers, I c variations within individual manufacturers, and often significant lengthwise fluctuations. The understanding of such variations is complicated by the lack of a direct correlation between I c and the critical current density J c . In fact, although J c is the fundamental property determined by the local vortex pinning landscape, I c is often limited by variable current blocking mechanisms. An important practical complexity is commercial practices of performing J c and I c evaluations based on I c at 77 K and self-field (sf), where connectivity variation dominates over vortex pinning variations. However, at higher fields and lower temperatures, vortex pinning becomes more complex and highly variable, making predictions of I c and J c at arbitrary temperature, magnetic field, and field orientation quite uncertain. To address some aspects of this problem, we conducted detailed spool-to-spool performance characterization on recently manufactured RE BCO coated conductors. Despite J c (77 K, sf) varies by only ~11%, J c (77 K, 1 T) of its minimum and maximum (for H // ab -plane) show variations of ~21% and ~32%, respectively. This emphasizes the shortcoming in using J c (77 K, sf) as parameter for evaluating even the low field performance. An even more remarkable spool-to-spool J c variation of ~68% was observed at 20 K and 15 T for H // ab -plane. To identify the origin of such lack of reproducibility we performed microstructural characterizations, which revealed, within the REBCO layer, large variation in the density of copper oxide (CuO x ) particles ranging from 0.1 to 2 μm in size. We believe that they play a decisive role in reducing the effective cross-section of the RE BCO layer by not simply blocking current themselves, but also by nucleating off-axis RE BCO grains, whose misoriented grain boundaries adversely impact RE BCO grain-to-grain connectivity. The RE BCO growth associated with high density CuO x particles also leads to the more disordered spatial arrangement of degrade the orientation of BaHfO 3 precipitate arrays, which, self-aligning along the ab -planes, generate strong pinning enhancing J c ( H // ab ) at all temperatures. In this way, we established that variations of both connectivity and vortex pinning are thus directly coupled. Our results also explain why the so-called "lift-factor", typically defined by the ratio between I c ( T , H ) and I c (77 K, sf), frequently turns out to be unreliable.

  • Screening Current-Induced Stress and Strain Analysis Considering a Non-uniform Thickness Profile of REBCO Tapes

    by Yu Suetomi, Shannon Griffin, Hongyu Bai, Mark Bird, Dmytro Abraimov, Adonay Almanza-Enriquez, Noah Gavin, Jun Lu, Iain R. Dixon

    Winding compressibility (WCP) is a significant reduction in the effective radial Young's modulus of REBCO pancake coils compared with the sum of the various macroscopic components, due to microscopic asperities on the tape surface and/or a non-uniform tape profile. For pancakes that are impregnated either not at all or with something soft like paraffin, this has a substantial impact on the screening current induced stress (SCIS) calculation. In this study, we propose a modeling technique called Penalty Function with Gap Offset (PGO) that incorporates non-uniform tape profiles as a gap offset distribution within contact boundaries. We also evaluate the effectiveness of reinforcement options—co-winding (CW), over-banding (OB), and outer ring (OR)— by considering winding compressibility.


  • Fabrication and Test of C3a: A Six-Layer Subscale Canted $\cos \theta$ Dipole Magnet Using High-Temperature Superconducting corc Wires

    by Dmytro Abraimov, Diego Arbelaez, Lucas Brouwer, Helen Feng, Paolo Ferracin, William B. Ghiorso, Hugh C. Higley, Mariusz Juchno, Andy Lin, Thomas Lipton, et al.

    rebco coated conductors have a strong potential for high-field magnet applications. The rebco technology, however, is still in its infancy for accelerator magnet applications. As part of the U.S. Magnet Development Program, we developed a six-layer canted $\cos \theta$ dipole magnet, C3a, using corc wires developed by Advanced Conductor Technologies LLC. All the layers were wound using a semiautomated winding machine. Three layers of the magnet used corc wires containing the SuperPower “AP” rebco tapes and the remaining layers used the wires containing the “HM” tapes. At 77 K, both kinds of corc wires showed 5% to 10% degradation, after bending to a minimum bend radius of 30 or 35 mm, with respect to the self-field critical current measured before winding. At 4.2 K, the magnet reached 9.5 kA at a ramp rate of 9 A s$^{-1}$ and generated a dipole field of 1.4 T. The critical current of one layer degraded by 4% after a current transient up to 10.5 kA ramped in an averaged rate of 175 kA s$^{-1}$ or 20 T s$^{-1}$. We confirmed the HM corc wire can carry a higher current than the AP corc wire at 4.2 K. The test results of the C3a magnet showed that the fabrication and assembly procedure can be used for the upcoming full-scale C3 magnet.


  • Optimization of Transport Critical Currents at 4.2 K – 20 K at Magnetic Fields Up to 31 T for MOCVD REBCO Conductors With Variable Zr and Growth Conditions

    by D. Abraimov, J. Gillman, C. Zha, Y. Oz, H. Pimentel, S. Mao, J. Kvitkovic, G. Bradford, J. Lee, J. Jaroszynski, et al.

    The critical current, $I_{\mathrm{c}}$, of REBCO full-width 4 mm short samples made by metal-organic chemical vapor deposition (MOCVD), optimized for high-field applications, were measured at magnetic fields perpendicular to sample plane up to 31.2 T in resistive magnets and temperature range ${\text{4.2}}\,{\text{K}}$–55 K. Dependencies of $I_{\mathrm{c}}$, critical current density ($J_{\mathrm{c}}$), and pinning force density ($F_{\mathrm{p}}$) on Zr doping and REBCO growth conditions were studied. SEM images of cross-section and top view of the REBCO layers for tapes with 15%, 20%, and 25% Zr doping show dense REBCO layers without secondary phases or porosity. REBCO tapes with 20% and 25% Zr doping perform better in transport $I_{\mathrm{c}}$(T,$\mu _{o}H$) tests at 20 K and 20 T conditions than tapes with lower Zr doping and can be promising candidates for applications focusing on magnetic plasma confinement.


  • A Comprehensive Characterization of Commercial Pulsed Laser Deposited Coated Conductors

    by Aixia Xu, Yan Xin, Dmytro Abraimov, Jin Gyu Park, Jan Jaroszynski, Fumitake Kametani, David C. Larbalestier

    Comprehensive understanding is needed in order for the commercial pulsed laser deposited REBa2Cu3O7-δ (RE: rare earth) coated conductors to be effectively used in the magnet and cable designs. Here we demonstrate the superconducting property characterization and microstructural analysis to show how different or similar the 3 commercial REBCO coated conductors are at present. Our work shows that the ab-plane of REBCO tilts from the coated conductor tape plane, leading to the offset of critical current density peak from the tape plane. In particular, the offset angle varies from less than 0.5° for one coated conductor to close to 5° for another. RE2O3 nanoparticles are dominant pins at 20 K and 15 T. The weak pinning introduced by RE2O3 particles and cation disorders contribute to critical current density at 20 K as well.


  • Lengthwise Characterizations of Crystallographic Tilt in Contemporary REBCO Coated Conductors

    by Jonathan Lee, Jeseok Bang, Griffin Bradford, Dmytro Abraimov, Ernesto Bosque, David Larbalestier

    Simulations may fail to accurately replicate the stresses experienced by no-insulation (NI) REBCO coils during operation and the resulting damage patterns observed postmortem in the coated conductor (CC). These simulations often assume that the REBCO layer's ab-planes are parallel to the CC tape plane, but in reality, the planes may deviate by several degrees. Since the nominal field angle lies close to the sharp ab-plane peak in the angular Ic of REBCO tapes, this small crystallographic tilt produces large discrepancies between expected and actual Ic, resulting in large inaccuracies for screening current stress (SCS) calculations. In this study, we use nondestructive XRD rocking curves to explore lengthwise variations in the ab-plane tilt angle in CCs from three anonymized manufacturers. We find that in two of the CCs, the tilt angles remain consistent along the length, but in the third CC, the tilt fluctuates on short length scales and wanders on long length scales. The tilt consistency loosely correlates with Ic homogeneity assessed using 77 K reel-to-reel remnant magnetization scans, though we do not find direct correlations between short-scale tilt fluctuations and Ic fluctuations. Our findings suggest that nondestructive lengthwise XRD ab-plane tilt measurements should be incorporated, when possible, into the conductor selection process when designing NI magnets.


  • CORC® wires allowing bending to 20 mm radius with 97.5% retention in critical current and having an engineering current density of 530 A mm−2 at 20 T

    by Danko van der Laan, Jeremy Weiss, Kyle Radcliff, Dmytro Abraimov

    Low-inductance, high-field insert solenoid magnets and 20 T dipole magnets for particle accelerators require flexible cables, wound from high-temperature superconductors (HTS) such as RE-Ba2Cu3O7− δ (REBCO) coated conductors, that allow bending to a 20 mm radius without significant degradation in performance. They require an operating current of at least 5 kA and a high engineering current density (J e) exceeding 500 A mm−2 at 20 T. HTS cable technologies that target such demanding magnet applications so far have not been able to meet the combination of these requirements. Here we present the development of the next generation of Conductor on Round Core (CORC®) wires that are produced with an optimized manufacturing process that improves their bending flexibility by factor of more than 2 compared to previous generation CORC® wires. CORC® wires now allow for a bending radius of 20 mm with only 2%–3% performance degradation. They allow bending to a radius of 15 mm with a performance retention of 83.5%. The performance of 30-tape CORC® wires wound from 2 mm wide REBCO tapes from SuperPower Inc, SuperOx and shanghai superconductor technologies was measured at magnetic fields up to 12 T. The overall performance at high magnetic fields of the next generation of CORC® wires improved by a factor of 1.5–1.8, depending on the REBCO tape manufacturer. CORC® wires wound from production REBCO tapes achieved a new record J e of 751 A mm−2 at a current of 8.3 kA at 12 T, and a J e of 530 A mm−2 at a current of 5.8 kA when extrapolated to 20 T. The next generation of CORC® wires present the first HTS cable technology that simultaneously meet the requirements on bending flexibility, engineering current density and critical current at 20 T for use in low-inductance, high-field particle accelerator magnets. They now enable a more expedited development of prototype low-inductance solenoid magnets that target fields exceeding 25 T and of accelerator magnets that generate a dipole field exceeding 20 T.


  • The Effect of Field-Dependent $n$-Value on Screening Current, Voltage, and Magnetic Field of REBCO Coil

    by Jeseok Bang, Kwangmin Kim, Griffin Bradford, Jonathan Lee, Dmytro Abraimov, Mato Takanobu, So Noguchi, Seungyong Hahn, David Larbalestier

    Here we report the effect of field-dependent index value $n(B,\theta)$ on screening current and consequential NI REBCO coil behavior. Through the ‘Little Big Coil (LBC)’ framework, an unexpected voltage behavior has been observed at the top and bottom coils in the fourth mini magnet LBC4 during the self-field operation at 77 K. The measurement demonstrates that the top/bottom coil voltage is temporarily decreased and then increased. However, this anomaly cannot be reproduced if the conventional simulation model uses the power-law $E\!-\!J$ model with a constant $n$ -value. Hence, we have revisited a property of the REBCO-coated conductor and, as a result, found that the field dependency of $n$ is necessary to elucidate the behavior. This paper will provide the 77 K self-field operation results, e.g., module coil voltages and the central magnetic field. A numerical simulation considering the field dependency investigates unexpected coil voltage behavior. The comparison between simulation results if the dependency is included and if not will be discussed.